Mitsubishi Projector Xd2000u User Manual

EN-11
ENGLISH
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit de-
signed for this projector. Ask a specialist for installation. 
For details, consult your dealer.
•  The warranty on this projector does not cover any 
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location. 
•  When using the projector mounted on the ceiling, 
set IMAGE REVERSE in the INSTALLATION menu to 
MIRROR INVERT. See...

EN-12
Screen size and projection distance
Refer to the following table to determine the screen size. 
When the aspect ratio of the screen is 4:3
 Screen size  Projected distance (L)  Lens movable range
 4:3  Diagonal size   Height (H)   Width (W)  Min.   Max.   (H1)   (H2)   width (W1)
 inch  cm inch  cm inch  cm inch  m  inch  m  inch  cm inch  cm inch  cm
•  The above fi gures are approximate and may be slightly different from the actual measurements.
•  The lens movable range shows distances from the...

EN-13
ENGLISH
2 1
AUDIO OUTAUDIO IN
2 1
2 1
Viewing computer images
A. Connecting the projector to a computer
Preparation: 
•  Make sure that the power of the projector and that of the computer are turned off. 
•  When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor. 
For analog connection: 
(For using the COMPUTER/COMPONENT VIDEO IN-1 
terminal.)
1.  Connect one end of the supplied RGB cable to the 
COMPUTER IN/COMPONENT VIDEO IN-1 terminal of...

EN-14
2 1
1.  Plug the attached power cord into the power cord inlet of 
this projector.
2.  Plug the other end of the power cord into a power outlet.
•  The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
country. 
•  This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power 
plug. If the power plug doesn’t fi t your wall outlet, ask an electrician to change the wall outlet. 
•  The provided...

EN-15
ENGLISHPOWER
MENUENTERS TAT U S
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.)...

EN-16
POWER
MENUENTERSTATUS
AUTO POSITION
COMPUTER
ZOOM/FOCUS LENS SHIFT
KEYSTONE
VIDEO
VOLUME
Viewing computer images (continued)
To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes...

EN-17
ENGLISHConnecting to a video player, etc.
1.  Connect one end (yellow) of the supplied audio/video cable 
to the VIDEO IN terminal of the projector. 
2.  Connect one end (white and red) of the supplied audio/
video cable to the audio input terminals (L/MONO, R) of the 
projector. 
3.  Connect the other end (yellow) of the audio/video cable to 
the video output terminal of the video equipment. 
4.  Connect the other end (white and red) of the audio/video 
cable to the audio output terminals (L, R)...

EN-18
CB(PB) Y CR(PR) 
B  G R 
AUDIO IN-2
BNC cable (Option)
DVD player or HDTV decoderBNC - RCA connector (option)COMPUTER IN/COMPONENT VIDEO IN-2
Connecting to video equipment having a DVI-D terminal
You can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a 
DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data 
that are output from DVD players. 
•  Use DVI cable for connection.
•...

EN-19
ENGLISH
C. Projecting images
Preparation:
•  Remove the lens cap.
1.  Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
•  If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating 
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator. 
2....

EN-20 To stop projecting:
13. Press the POWER button. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press any button except the POWER button. 
14. Press the POWER button again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
15. Wait about 2 minutes for the STATUS indicator to be turned off. 
•  During this period of 2 minutes in the standby mode, the intake fan and...