Mitsubishi Hd8000u Projector User Manual

EN-31
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
W button is pressed, the image moves to...

EN-32
Set the background color
(Set the background color only when you set the im-
age size to x1 or x4.)
6.  Select BACK COLOR by pressing the 
S or 
T but-
ton.
7.  Select your desired color for the background (GRAY, 
RED, GREEN, BLUE, BLACK, WHITE, RED50%, 
GREEN50%, or BLUE50%) by pressing the 
W or X 
button. 
Set the image size
8.  Select SIZE by pressing the 
S or 
T button.
9.  Select x1, x4, or FULL by pressing the 
W or X but-
ton. 
Capture the image
10. 
 Select CAPTURE by pressing the 
S or...

EN-33
MENU ACCESSFEATURE
opt.
LOCK
UNLOCKOK
OK
PASSWORD
CONFIRM
1
32 4
O K : ENTER CANCEL : MENU
MENU ACCESSFEATURE
opt.
LOCK
UNLOCKOK
OK
PASSWORD
1
32 4
O K : ENTER CANCEL : MENU
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specifi ed users. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen (or splash screen) will ap-
pear and stay on the...

EN-34
Split
You can split the screen in two and display a computer 
image on the left screen and a video image on the right 
screen. 
Left screen Right screen
To use the split mode:
1.  Press the SPLIT button on the remote control. 
•  The screen is split in two and the left and right 
screens display the following images:
- Left screen:  Image supplied to the last se-
lected input source, COMPU-
TER1, COMPUTER2, or DVI
- 
Right screen:   Image supplied to the last 
selected input source, VIDEO 
or...

EN-35
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote 
control. 
Projector + computer with USB connector
Operation
•  You can use the mouse remote control function with a computer supporting USB only. 
•  When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case, 
restart the computer.
•  The mouse doesn’t function for a while after the power is turned on. 
•  When a...

EN-36
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network. 
•  To supervise and control the projector, install the software “Projector-Control Device Installer *” contained in the 
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control 
Utility” contained in the attached CD-ROM. 
 *) Functions
•  Setting of the projector’s IP address
•  Setting of password, display...

EN-37
Indicators
POWER 
Steady
green 
or
Steady red 
Steady red 
Steady
green 
Steady red 
Steady red 
Blinking
green/red 
Blinking
green/red 
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red 
Steady red 
Off
Steady
or
Blinking
CONDITION 
Abnormal temperature
•  The ventilation grilles are clogged with dust or dirt.
•  The room temperature is high.
•  The filter is dirty.
The protection circuit is working or the lamp is in an 
abnormal condition.
  
The lamp or cover isn’t closed....

EN-38
This projector includes a terminal cover with Anti-Theft 
Alarm device. Once the terminal cover is installed, its 
Anti-Theft Alarm device will detect vibration caused by 
the projector being moved and emit an alarm. 
•  Mitsubishi assumes no responsibility or liability for 
theft or other damages. 
Procedure for setting the anti-theft alarm 
device
Inserting the batteries into the theft warning device
1.  Open the battery cover of the theft warning device. 
2.  Check the (+) and (-) ends of the...

EN-39
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. 
Spare lamp  VLT-XL6600LP
Warning:
•  Be careful not to drop the lamp fi xing screws into the inside of the projector. Don’t put...

EN-40
(a)
(b)
(c)
(c)
Replacing the lamp (continued)
To replace the lamp: 
1.  Turn off the main power switch and unplug the power cord. 
2.  Reverse the projector gently.
3.  Loosen the screw (a) using a Phillips screwdriver (+), and 
remove the lamp cover (b).
4.  Loosen the screws (c) using a Phillips screwdriver (+).
5.  Pull up the handle. 
6.  Pull out the lamp box by the handle while holding the 
projector.
 Pull the lamp box out of the projector slowly. If it is 
pulled out quickly, the lamp may...