Mitsubishi Hd8000u Projector User Manual

							EN-31
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
W button is pressed, the image moves to the right. Every time 
the 
X button is pressed, the image moves to the left. 
The projected image is displaced vertically....................Adjust VERT.POSITION in the SIGNAL menu. Every time the 
W 
button is pressed, the image moves down. Every time the 
X 
button is pressed, the image moves up. 
The top part of the image fl ags. .....................................Change the setting of HOLD in the SIGNAL menu. Select ON , 
press the ENTER button, and adjust BEGIN or END to minimize 
the fl agging.
A solid black or solid white appears in the image.  ........ Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - 
USER menu.
The motion doesn’t run smoothly. ..................................Adjust VERT. SYNC in the SIGNAL - USER menu. Select 
AUTO for normal use. 
Noise appears on the right or left half of the image.
 ......Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL - USER 
menu.
Noise appears on the top or bottom part of the image.
 .......Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER 
menu.
1. Display the SIGNALmenu. 
2. Press the 
S or 
T button to select an item to adjust. 
3.  Adjust the selected item by pressing the 
W or 
X button. 
To cancel the menu:
4.  Press the MENU button. 
•  Do not change the settings of the SIGNAL menu in normal use. 
Simple method to adjust the image position
To adjust the horizontal position: 
1.  Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the 
right edge of the image with the right side of the screen by adjusting TRACKING. 
2.  Repeat step 1 above to complete the adjustment of the horizontal position. 
To adjust the vertical position: 
3.  Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION. 
LPF (Progressive fi lter) 
You can select whether or not to enable the LPF. 
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or 
game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected 
images become softened slightly. 
Adjusting projected images  (continued) 
						

							EN-32
Set the background color
(Set the background color only when you set the im-
age size to x1 or x4.)
6.  Select BACK COLOR by pressing the 
S or 
T but-
ton.
7.  Select your desired color for the background (GRAY, 
RED, GREEN, BLUE, BLACK, WHITE, RED50%, 
GREEN50%, or BLUE50%) by pressing the 
W or X 
button. 
Set the image size
8.  Select SIZE by pressing the 
S or 
T button.
9.  Select x1, x4, or FULL by pressing the 
W or X but-
ton. 
Capture the image
10. 
 Select CAPTURE by pressing the 
S or 
T button.
11.Press the ENTER button.
• A red frame appears. (The size of the red frame 
is 640 x 360 pixels.)
12.Adjust the size of the image to be captured so that 
such image stays within the red frame. 
• Press the 
S, 
T, W or X button to move the red 
frame.
• You can’t move the red frame outside the 
screen. 
13. Press the ENTER button twice.
• Image capture will start.
• Press the MENU button to cancel the proce-
dure.
• When the image capture completes, the cap-
tured image will be displayed for three seconds. 
Important:
• You can’t change the new startup screen back to 
the original startup screen. (Even when you select 
RESET ALL in the FEATURE menu, the factory 
default screen isn’t available any longer.) When you 
want to change the startup screen again, capture 
another image.
• The captured image will be displayed from the next 
startup. If the captured image isn’t displayed, make 
sure that the setting of SPLASH SCREEN in the 
INSTALLATION menu isn’t OFF. (See page 24.)
• To display the captured image while the video is 
muted, set MUTE MODE in the INSTALLATION 
menu to IMAGE. (See page 24.)
• When BACK COLOR in the INSTALLATION menu is 
set to IMAGE, the captured image will be displayed 
while no signal is supplied. 
•  In the mute mode, or when no signal is input, it 
takes longer time to display the captured image.
• 
Some images can’t be captured correctly because 
of their signal type. 
CAPTURE : ENTER + ENTER
CANCEL : MENUCAPTURE : ENTER + ENTER
CANCEL : MENU
CAPTURE : ENTER + ENTER
CANCEL : MENU
CAPTURE : ENTER + ENTER
CANCEL : MENULVP-XD300 LVP-XD300CAPTURING IMAGE !
x1 x4 FULL
Setting of the image displayed 
during startup or muting
You can display your desired image as the startup 
screen (or splash screen). Using the menu, you can 
also use such image as a background that is displayed 
while the video is muted or no signal is supplied.
Important:
• You can’t set IMAGE CAPTURE when PASSWORD 
FUNCTION in the FEATURE menu has been set to 
SPLASH ID SCREEN to enable the password lock.
• You can’t set IMAGE CAPTURE when the compo-
nent video signal is inputted.
Setting procedure 
1.  Press the COMPUTER button to select the image 
supplied to the COMPUTER/COMPONENT VIDEO 
IN terminal.
2.  Display your desired image.
3.  Display the INSTALLATION menu.
4.  Select IMAGE CAPTURE by pressing the 
S or 
T 
button.
5.  Press the ENTER button.
• The setting menu will be displayed.
Advanced features
opt.
INSTALLATION
CUSTOM IMAGE CAPTURE
BACK COLOR
SIZEGRAY
x1
CAPTURE
GO 
						

							EN-33
MENU ACCESSFEATURE
opt.
LOCK
UNLOCKOK
OK
PASSWORD
CONFIRM
1
32 4
O K : ENTER CANCEL : MENU
MENU ACCESSFEATURE
opt.
LOCK
UNLOCKOK
OK
PASSWORD
1
32 4
O K : ENTER CANCEL : MENU
Password function
This projector is equipped with the password function 
that is designed for prevention of wrong operation by 
children and restriction on operation by other than 
specifi ed users. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen (or splash screen) will ap-
pear and stay on the screen until the password is 
entered. When the password is entered, the startup 
screen will switch to the regular operation screen.
MENU ACCESS ........... All the buttons except for the 
POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You 
can use this mode as a measure of prevention 
of wrong operation by children and restriction on 
operation by other than specifi ed users.
SPLASH ID SCREEN ... IMAGE CAPTURE and SPLASH 
SCREEN in the menu become unavailable. SPLASH 
SCREEN will be set to ON automatically.
To enable the password function:
1.  Display the FEATURE menu.
2. Press the 
S or 
T button to select PASSWORD 
FUNCTION.
3. Press the W or X button to change the mode 
among DISPLAY INPUT 
, MENU ACCESS  and 
SPLASH ID SCREEN 
.
•  When the password has already been set, the 
mode won’t be changed. In such cases, press 
the ENTER button to cancel the password func-
tion and try again. 
4.  Press the ENTER button.
•  The screen for setting the password function will 
appear. 
5.  Press the ENTER button.
•  The screen for entering a password will appear. 
6.  Enter a 4 - 8 digit password using the 
S, X, 
T or 
W
 buttons on the remote control as shown below.
 (
S=1, X=2, T=3, W=4) 
7.  Press the ENTER button.
•  To cancel the procedure, press the MENU 
button. 
8.  Enter the password again for confi rmation using the 
same steps.
Advanced features  (continued)
9.  Press the ENTER button. 
•  If the entered passwords don’t match, an error 
message will appear. 
•  To cancel the procedure, press the MENU 
button. 
To cancel the password function: 
1.  Display the FEATURE menu.
2. Press the 
S or 
T button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for canceling the password function 
will appear.
4.  Press the ENTER button.
•  The screen for entering the password will 
appear. 
5.  Enter a 4 - 8 digit password using the 
S, X, 
T or 
W
 buttons on the remote control as shown below.
 (
S=1, X=2, T=3, W=4) 
6.  Press the ENTER button.
•  If you enter a wrong password, an error message 
will appear.
•  To cancel the procedure, press the MENU 
button. 
Important:
•  Disable the password by pressing the MENU and 
ENTER buttons on the control panel at the same 
time about three seconds. 
						

							EN-34
Split
You can split the screen in two and display a computer 
image on the left screen and a video image on the right 
screen. 
Left screen Right screen
To use the split mode:
1.  Press the SPLIT button on the remote control. 
•  The screen is split in two and the left and right 
screens display the following images:
- Left screen:  Image supplied to the last se-
lected input source, COMPU-
TER1, COMPUTER2, or DVI
- 
Right screen:   Image supplied to the last 
selected input source, VIDEO 
or S-VIDEO
• When you press the SPLIT button again, the 
screen is displayed in the normal mode.
•  Also, when you press the MENU button or 
change the input source, the screen is displayed 
in the normal mode. 
• 
In the split mode, audio of the left screen is 
output.
•  In the split mode, the picture quality settings 
of the input source in the normal mode to be 
displayed on the left screen are refl ected on the 
entire screen.
• 
When no signal is input, a blue screen is 
displayed.
•  When you input an interlace signal to the left 
screen, the displayed image may shake up and 
down slightly, but this is not a malfunction.
• When you display 60-Hz and 50-Hz video signals 
at the same time, motion images may not be 
displayed properly. In this case, set VERT. SYNC 
of USER in the SIGNAL menu to OFF for the left 
screen. (See page 26.)
•  When BACK COLOR of the INSTALLATION 
menu is set to IMAGE, you cannot use the split 
mode. 
To change the input source of the left or right screen: 
• To change the input source of the left screen, press 
the 
W button on the remote control.
• To change the input source of the right screen, 
press the 
X button on the remote control.
Advanced features  (continued)
Freeze
To stop the motion in the image temporarily (or to 
display a still image):
Press the FREEZE button on the remote control.
•  The image will freeze temporarily.
To resume the motion in the image:
Press the FREEZE button on the remote control again.
Important:
•  Do not display a still picture for a long time because 
the afterimages may persist on the screen. (See 
page 44.) 
						

							EN-35
Mouse remote control
By connecting to personal computer through the USB port, you can operate your computer with the projector remote 
control. 
Projector + computer with USB connector
Operation
•  You can use the mouse remote control function with a computer supporting USB only. 
•  When the lamp is turned ON, the computer connected with the USB cable may not work correctly. In this case, 
restart the computer.
•  The mouse doesn’t function for a while after the power is turned on. 
•  When a computer is connected using a long USB cable, it may not be controlled by the remote control correctly. 
To extend the cable length, you are recommended to use a repeater.
COMPUTER
VIDEO S-VIDEO
DVI-D(HDCP)
HOME Page Up
END Page DownAUTO POSITION
KEYSTONELENS SHIFT ZOOM / FOCUS
12
MENUENTER
LASER
R-CLICK
USB
Mouse pointer
Use to move the cursor on 
the image, instead of the 
computer mouse.R-CLICK button
This operates in the 
same way as the right 
button on the computer 
mouse.L-CLICK button
This operates in the 
same way as the left 
button on the computer 
mouse.  USB cable
(option)
USB 4-pin
(type B)USB 4-pin
(type A)
To USB port
HOME button
Press to jump back 
to the fi rst page.
END button
Press to jump to the 
last page.Page Up button
Press to go back to 
the previous page.
Page Down button
Press to go to the 
next page.
Advanced features  (continued) 
						

							EN-36
Supervising and controlling by computer
You can supervise and control the projector’s operation using a personal computer via a LAN network. 
•  To supervise and control the projector, install the software “Projector-Control Device Installer *” contained in the 
attached CD-ROM. For the installation procedure and usage of the software, see “User Manual for LAN Control 
Utility” contained in the attached CD-ROM. 
 *) Functions
•  Setting of the projector’s IP address
•  Setting of password, display language, and LAN control
• PJLink™ certifi cation setting (telnet function)
•  Startup of the controlling /supervising tool (ProjectorView) using the Web browser
Major functions
ProjectorView
The controlling /supervising tool using the Web browser 
PJLink™
This projector supports standard protocol 
PJLink™ for projector control and you can control and monitor projector’s 
operations using the same application among projectors of different models and different manufacturers. 
About PJLink™
•  To use PJLink™ function, the PJLink™ application software is required. 
• For the specifi cations of 
PJLink™, access to the Web site of Japan Business Machine and Information System 
Industries Association (JBMIA)
. (http://pjlink.jbmia.or.jp/english)
•  This projector is fully compliant to the specifi cations of JBMIA 
PJLink™ Class 1. It supports all the commands 
defi ned by 
PJLink™ Class 1, and the compliance has been verifi ed with the PJLink™ standard specifi cations 
Version 1.0.
Connection
Computer
To LAN terminal
LAN cable (option)
(100BASE-TX or 10BASE-T should be supported.)LAN cable (option)
(100BASE-TX or 10BASE-T 
should be supported.)
External HUB
•  Use a straight-through category-5 cable for LAN connection.
•  Don’t touch the metal parts of the LAN connector and LAN cable because static electricity may be discharged from 
your body, causing damage to the projector.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM. 
Opening the User Manual:
1.  Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM “HD8000.”
3.  Double-click on “MANUAL_LAN.HTML” within the CD-ROM. A language selection list for the User Manual will be 
displayed.
4.  Move the mouse pointer to the desired language and click. 
Advanced features  (continued) 
						

							EN-37
Indicators
POWER 
Steady
green 
or
Steady red 
Steady red 
Steady
green 
Steady red 
Steady red 
Blinking
green/red 
Blinking
green/red 
STATUS
Blinking orange
Blinking green
Blinking green/red
Blinking red 
Steady red 
Off
Steady
or
Blinking
CONDITION 
Abnormal temperature
•  The ventilation grilles are clogged with dust or dirt.
•  The room temperature is high.
•  The filter is dirty.
The protection circuit is working or the lamp is in an 
abnormal condition.
  
The lamp or cover isn’t closed. 
Abnormal. POSSIBLE SOLUTION 
•  Clean the ventilation grilles.
•  Relocate the projector to a cooler place.
•  Clean the filter.    
•  Wait until the STATUS indicator goes out, 
    then press the POWER button.
•  If the above solution is not effective, 
    replace the lamp.
Replace the lamp.
Change with a new lamp if this problem 
recurs.
Close the cover correctly.
Contact your dealer.
 Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be
 shorted.  * 
1  
* 
2  When LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.Lamp operation time warning. (Total lamp operation time 
reached 3000 hours
*1 while the power was on.)
Lamp operation time warning. (Total lamp operation time 
reached 3000 hours
*1 while the power was off.)
Lamp operation time warning. (Total lamp operation time 
reached 4000 hours
*1*2 while the power was off.)
This projector has 2 indicators, each of which shows the operation condition of the projector. 
The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your 
dealer. 
Normal condition
Abnormal condition
STATUS indicator
POWER indicator 
POWER 
Steady  
red
Steady
green
S TA  TUS 
Off
Steady 
green
CONDITION 
Stand-by
Lamp stand-by for power-on (about 1 minute)
The power is on. (Normal condition)
NOTE 
The power cannot be turned off by pressing 
the POWER button.
For the first one minute, the power cannot be 
turned on by pressing the POWER button.
Steady
greenBlinking Lamp stand-by for power-off (about 2 minutes)
r green 
						

							EN-38
This projector includes a terminal cover with Anti-Theft 
Alarm device. Once the terminal cover is installed, its 
Anti-Theft Alarm device will detect vibration caused by 
the projector being moved and emit an alarm. 
•  Mitsubishi assumes no responsibility or liability for 
theft or other damages. 
Procedure for setting the anti-theft alarm 
device
Inserting the batteries into the theft warning device
1.  Open the battery cover of the theft warning device. 
2.  Check the (+) and (-) ends of the battery, and insert 
it from the (-) end fi rst.
ON
Battery cover
Power switch
•  Inserting the battery from the (+) end makes 
it diffi cult to fi t the (-) end into the coil spring. 
Forcing in the battery in such a position may 
shred the outside label, causing a short circuit 
and overheating. 
•  See page 6 for information on how to handle 
batteries. 
3.  Close the battery cover.
Safety pin hole
Safety pin
Screws
4.  Insert the included safety pin into the safety pin 
hole. 
•  If the safety pin is not inserted, the vibrations 
and shocks of normal use may cause the alarm 
to sound. 
5.  Turn the power switch ON.
Installing the terminal cover
1.  Insert the four tabs on the terminal cover into the 
holes on the projector’s side. 
2.  Slide the terminal cover toward the back of the 
projector. 
Ta b s
3.  Tighten the three screws that keep the terminal 
cover in place. 
Terminal cover (with anti-theft alarm device)
4.  Install the projector in a specifi ed location. 
5.  Press the battery level check button until you hear 
a buzzer sound.    
6.  Remove the safety pin. 
  The anti-theft alarm device is now in standby. 
•  This package includes a sticker which shows 
that the anti-theft alarm device is active. Visible 
placement of this sticker is recommended.
•  To temporarily halt the anti-theft alarm device, 
insert the safety pin. 
•  Vibrations will not cause the alarm to sound for 
several seconds after the power switch is turned 
ON.  
•  Vibrations will not cause the alarm to sound for 
several seconds after the safety pin is removed. 
•  Vibrations and shocks from earthquakes may 
cause the alarm to sound. In such situations, 
insert the safety pin to halt the alarm.
•  Batteries may come loose during transportation. 
Please remove them beforehand.  
Procedure for changing batteries
How to check battery level
Use a pointed object to push the battery level check 
button. 
Battery level 
check button
•  A buzzer will sound while the button is being 
pushed. If there is no buzzer sound, then batteries 
need to be changed.  
•  Sounding the buzzer for a long time will consume 
battery power. 
Changing the batteries
1.  Insert the safety pin into the safety pin hole. 
2.  Loosen the three screws that keep the terminal 
cover in place.
3.  Slide the terminal cover toward the front of the 
projector. 
4.  Pull the terminal cover toward you and remove it. 
•  Attention must be paid when removing the 
terminal cover as there could be foreign objects 
inside.
•  Removal of dust found inside the terminal cover 
is recommended when changing batteries. 
5.  Open the battery cover and remove the old 
batteries.
6.  Check the (+) and (-) ends of the new battery, and 
insert it from the (-) end fi rst. 
•  Use alkaline AA batteries. 
•  Standard battery life is approx. six months (when 
using alkaline dry cell batteries). Please check 
the battery level and change batteries regularly. 
7.  Close the battery cover.  
						

							EN-39
Replacing the lamp
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp. 
Spare lamp  VLT-XL6600LP
Warning:
•  Be careful not to drop the lamp fi xing screws into the inside of the projector. Don’t put a metal piece or fl ammable 
object into the projector. Using the projector with any foreign object present inside may result in electric shock or 
fi re. When you can’t remove the foreign object from the inside, contact your dealer for removal. 
•  Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation 
may also result in fi re.
•  Don’t shake the removed lamp or don’t lift it above your face. You may be injured in your eye by fl ying or falling 
glass fragments.
•  Don’t replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the 
power using the POWER button. After the lamp goes out, wait about 2 minutes until the intake and exhaust fans 
for cooling the lamp stop rotating. Then turn off the main power switch, unplug the power cord, and wait at least 1 
hour to allow the lamp to cool down enough to the touch.
•  Do not touch the lamp directly. It may break and cause injury or burn.
Interval of lamp replacement
The recommended interval of lamp replacement is about 4000 hours*1*2 of consecutive use. Such interval differs 
depending on the operating environment and may be shorter than 4000 hours*1*2. Decrease in luminescence and/or 
color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3000 hours*1, 
the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator 
will be lit red only) and the lamp replacement message will appear on the screen for 1 minute everytime the lamp 
is turned on. When the lamp has been used for about 3800 hours
*1, the replacement message (LAMP EXCHANGE) 
will appear on the screen for 1 minute every 20 hours*1 thereafter. When the lamp operation time exceeds 4000 
hours*1*2, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp 
operation time is reset.
*1:  Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be 
shorted.
*2:  When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
Caution:
•  Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a 
breakdown.
•  This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may 
explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period 
of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on 
operation conditions. Therefore, the lamp may explode soon after the start of use. 
•  The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction 
of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally. 
•  When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and 
the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains 
mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it 
should enter your eye or mouth, see a doctor immediately.
•  In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the 
projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace 
the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments. 
•  Don’t replace the lamp while the projector is installed on the ceiling. Glass fragments may fall from the projector, 
entering your eye or mouth causing injury. 
•  When placing the projector upside down to replace the lamp or conduct maintenance, ensure that the projector is 
securely placed before working with it.
•  Be sure to use the lamp exclusive to this projector, VLT-XL6600LP. Use of other lamps may cause a failure of the 
projector. 
						

							EN-40
(a)
(b)
(c)
(c)
Replacing the lamp (continued)
To replace the lamp: 
1.  Turn off the main power switch and unplug the power cord. 
2.  Reverse the projector gently.
3.  Loosen the screw (a) using a Phillips screwdriver (+), and 
remove the lamp cover (b).
4.  Loosen the screws (c) using a Phillips screwdriver (+).
5.  Pull up the handle. 
6.  Pull out the lamp box by the handle while holding the 
projector.
 Pull the lamp box out of the projector slowly. If it is 
pulled out quickly, the lamp may break scattering glass 
fragments. 
 Do not spill liquid on the removed lamp box or do not 
place it near any  ammable object or where children 
can reach to prevent injury or  re.
7.  Load a new lamp box securely into the projector in the right 
orientation.
8.  Put the handle back to the original position.
 Make sure that the handle is locked.
9.  Tighten up the screws (c) using a Phillips screwdriver (+).
10. Tighten up the screw (a) using a Phillips screwdriver (+) to 
secure the lamp cover.
Reset of the lamp operation time
11. Plug the power cord into the wall outlet and turn on the 
main power switch.
12. Hold down the 
W, 
X, and POWER buttons on the control 
panel at the same time about 3 seconds.
Important:
 Unless these 3 buttons are held down at the same time, the lamp operation time isn’t reset. 
 Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully. 
 The projector doesn’t turn on if the lamp cover isn’t attached securely. 
 Be sure to reset the lamp operation time whenever you replace the lamp. 
 Do not reset the lamp operation time unless you replace the lamp. 
 The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
 Contact your dealer for a new lamp.
Caution:
This projector uses a lamp that contains mercury. Disposal of the lamp or the projector 
with the lamp may be regulated due to environmental considerations. For disposal or 
recycling information, please contact your local authorities or the Electronic Industries 
Alliance: www.eiae.org. (For the U.S. only.)
(a)
Handle