Mitsubishi Hd4000 Projector User Manual

EN-21
ENGLISH
POWER STATUS
C. Projecting images
Preparation:
•  Remove the lens cap.
•  Turn on the power of the connected computer. 
1. Confi rm the POWER indicator lights-up red. 
•  If the projector was turned off before the lamp had cooled down suffi ciently, the fan may start rotating and the 
POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the 
fan stops rotating, press the power button to turn back on the POWER indicator. 
2.  Press the POWER...

EN-22
BLANK mode
The video signal is temporarily muted when the BLANK button is pressed. To cancel muting, press the BLANK 
button again.
•    It takes several seconds to disable the BLANK mode.
AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1.  Display a bright image (such as a full-screen display of the Recycle Bin window). 
2.  When the screen saver has been enabled, disable it. 
3.  Press the AUTO POSITION button.  
    The projector...

EN-23
ENGLISH
Menu operation
•  Menus are not displayed when no signal is supplied to the projector. 
* 1: Not available with certain signals.
* 2: Available only when the input signal is TV50, TV60, 480i, or 
576i.
* 3: Available only when the input signal is from the VIDEO IN or 
S-VIDEO IN terminal.
* 4: Setting range differs depending on the input signals.
* 5: Not available when the input signal is from the VIDEO IN or 
S-VIDEO IN terminal.
IMAGE
CONTRAST ±30
BRIGHTNESS ±30
9300K
6500K
5900K
USER...

EN-24 How to set the menus:
The following describes how to set AUTO POWER OFF 
time as an example. 
1.  Press the MENU button. 
•  When no signal is applied, the menu would not 
appear. 
2. Press the 
 or 
 button to select a menu to use.  
3.  Press the ENTER button (or 
 button).
IMAGE
SVGA60opt.
AV MEMORY 1
INSTALLATION
SVGA60opt.
AV MEMORY 1
SCREEN SIZE
INSTALLATION
SVGA60
WXGA (15:9)
VERTICAL LOCATION0
opt.
AV MEMORY 1
4. Press the 
 or 
 button to select an item to ad-
just. 
5.  Set the...

EN-25
ENGLISH
2. INSTALLATION menu
ITEM SETTING FUNCTION
SCREEN SIZE 4 op
tions  Select according to the screen size.
VERTICAL LOCATION ±26  Use to adjust the position (height) of the projected image.
LAMP MODE  STANDARD  Select this option when you want to view images in a well-lit room.
  LOW  Select to moderate the intensity of the lamp. The fan operating sound is reduced 
and the lamp lifetime becomes longer. 
AUTO POWER ON  ON / OFF When ON is chosen, the lamp is automatically lit when the power...

EN-26
4. SIGNAL menu  5. USER menu
Menu operation (continued)
4. SIGNAL menu
ITEM SETTING FUNCTION
HORIZ. POSITION  0 - 999  Use to adjust the horizontal position of the projected image. 
VERT. POSITION  0 - 999  Use to adjust the vertical position of the projected image. 
FINE SYNC.  0 - 31 Use to eliminate fl ickering or blur, if it appears, while viewing the projected image. 
TRACKING  0 - 9999  Use to eliminate vertical wide stripes, if it appears, while viewing the projected 
image.
COMPUTER INPUT...

EN-27
ENGLISH
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the 
 or 
 button. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the 
 button is pressed,...

EN-28
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR TEMP.  by pressing the 
 or 
 button. 
3.  Select your desired color temperature by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your preference, carry out...

EN-29
ENGLISH
This projector automatically and properly projects video signals supplied from the computer. However, some video 
signals may not be projected, depending on the type of the computer. In such a case, press the AUTO POSITION 
button. (See page 22.) When the signal is still not projected properly, adjust the projected image using the SIGNAL 
menu. 
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips...

EN-30
DISPLAY INPUTLOCK
UNLOCKOKOK
PASSWORD
CONFIRM
O K CANCEL
DISPLAY INPUTLOCK
UNLOCKOKOK
PASSWORD
O K CANCEL
Password function
This projector is equipped with the password function 
that is designed for prevention of theft and wrong op-
eration by children and restriction on operation by other 
than specifi ed users. The password function has two 
modes as follows. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until...