Mitsubishi Hd4000 Projector User Manual

							EN-21
ENGLISH
POWER STATUS
C. Projecting images
Preparation:
•  Remove the lens cap.
•  Turn on the power of the connected computer. 
1. Confi rm the POWER indicator lights-up red. 
•  If the projector was turned off before the lamp had cooled down suffi ciently, the fan may start rotating and the 
POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the 
fan stops rotating, press the power button to turn back on the POWER indicator. 
2.  Press the POWER button on the projector or ON ( I ) button on the remote control. 
•  It may take about one minute for the lamp to light up. 
•  The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•  Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the 
lens cap. 
•  After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a prod-
uct malfunction. 
•  LAMP MODE can't switch for 1 minute after the power ON.
•  The projector starts warming up when the POWER button is pressed. During the warm-up process, images may 
appear dark and no commands are accepted.
•  By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See pages 34 and 37.) 
3.  Select an input source. 
•  Press the COMPUTER button on the projector or the COMPUTER or HDMI button on the remote control that is 
corresponding to the terminal in use. 
•  The input source is switched between COMPUTER and HDMI every time you press the COMPUTER button on 
the projector. 
•  Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction. 
•  Images may not be projected in the correct position, depending on the type of the input signal. In such a case, 
press the AUTO POSITION button. (See page 22.)
•  The projector automatically selects the appropriate signal format. The selected signal format is displayed on the 
screen.
• The 
COMPUTER and HDMI buttons don't function while the menu is being displayed. 
•  When COMPUTER is chosen as the source, images supplied from the computer may fl icker. Press the  or  
button on the remote control to reduce fl icker, if it occurs.
4.  Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes. 
5.  Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 
10.) 
•  When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
6.  Adjust the size of the projected image by turning the ZOOM ring. 
7.  Adjust the focus by turning the FOCUS ring. 
Repeat steps 4 to 7, if necessary. 
POWER button
COMPUTER button FOCUS ring
COMPUTER buttonHDMI button ZOOM ringON ( I ) button 
						

							EN-22
BLANK mode
The video signal is temporarily muted when the BLANK button is pressed. To cancel muting, press the BLANK 
button again.
•    It takes several seconds to disable the BLANK mode.
AUTO POSITION button 
When the image supplied from the computer is displaced, carry out the following procedure. 
1.  Display a bright image (such as a full-screen display of the Recycle Bin window). 
2.  When the screen saver has been enabled, disable it. 
3.  Press the AUTO POSITION button.  
    The projector automatically makes optimum positional settings for the input signal. 
•    If the image is not projected in the correct position even after you press the AUTO POSITION button several 
times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 29.)
•    When you carry out this procedure with a dark image, the image may be displaced. 
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of 
the computer you use.) 
To stop projecting:
8.  Press the POWER button on the projector or the OFF () button on the remote control. 
• A confi rmation message is displayed.
•  To cancel the procedure, leave the projector for a while or press the MENU button. 
9.  Press the POWER button on the projector or the OFF (
) button on the remote control again. 
•  The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green. 
10. Wait about one minute. 
•  During this period of one minute in the standby mode, the intake fan and exhaust fan rotate to cool the lamp. 
• The lamp cant be lit again for one minute after turning off the projector for safety purpose. It will take another 
one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator 
goes out, and then press the POWER button.
•  The air outlet fans rotate faster as the temperature around the projector rises.
•  Do not unplug the power cord while the STATUS indicator is blinking. Unplugging the power cord immediately 
after use may cause a lamp breakdown. 
•  Though the fan makes loud sounds during cooling, such symptom is not a malfunction. 
11. Unplug the power cord from the outlet. 
•  The POWER indicator will go out. 
•  If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are 
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the 
lamp again, press the POWER button. If the lamp doesnt light up immediately, repeat pressing the POWER 
button two or three times. If it should still fail to light up, replace the lamp. 
•  Cover the lens with the lens cap to protect it from dust. 
POWER STATUSPOWER buttonOFF (
) button
AUTO POSITION 
buttonBLANK button
Viewing computer images (continued) 
						

							EN-23
ENGLISH
Menu operation
•  Menus are not displayed when no signal is supplied to the projector. 
* 1: Not available with certain signals.
* 2: Available only when the input signal is TV50, TV60, 480i, or 
576i.
* 3: Available only when the input signal is from the VIDEO IN or 
S-VIDEO IN terminal.
* 4: Setting range differs depending on the input signals.
* 5: Not available when the input signal is from the VIDEO IN or 
S-VIDEO IN terminal.
IMAGE
CONTRAST ±30
BRIGHTNESS ±30
9300K
6500K
5900K
USER    
COLOR ±10
TINT ±10
SHARPNESS ±5
GAMMA MODE
CONTRAST B ±30
BRIGHTNESS R ±30
CONTRAST R ±30
CONTRAST G ±30
BRIGHTNESS G ±30
BRIGHTNESS B REFERENCE
HIGH
MID
LOW
±30
±5
±5
±5
SCREEN SIZE
WXGA(15:9), 720P(16:9), XGA(4:3), CINEMA SCOPE(2.35:1)
AUTO POWER ON
ON , OFF
VERTICAL LOCATION±26
USER1
USER2
RESET ALL OK  AUTO POWER OFF
MENU POSITION 1 (Upper left), 2(Lower right)
TEST PATTERN CROSS HATCH    
LAMP MODE
ASPECT
DISPLAY INPUT    ,MENU ACCESS    
ON, OFF AUTO, OFF, 3.75%, 7.5%
VIDEO SIGNAL
LANGUAGE, English, Español, Deutsch, Français, Italiano,        ,          ,             ,    
SIGNALHORIZ.POSITION
HOLD0 - 999
0 - 999
FINE SYNC. 0 - 31
TRACKING
USER0 - 9999
CLAMP POSITION0 - 255
CLAMP WIDTH1 - 63
VERT.SYNCAUTO, OFF *4 *6
*6
*5,*6 
*1*,5,*6 
*1*,5,*6
AUTO , OFF CINEMA MODE
*6,*7*6
*6
*1
*1
*1
*1
*1 *5*4
*4
ON
BEGIN0 - 99
END0 - 99 OFF
COMPUTER INPUT
*4
*4
*4
OVER SCAN100 - 90%
LPF ON, OFF
SHUTTER (U)
0 - 38
SHUTTER (L) 0 - 38
SHUTTER (LS) 0 - 95
SHUTTER (RS)
0 - 95
TRIGGER OUT ON , OFF
OK 
OK
UNLOCKOK 
LOCK *1,*6  *1,*6  
*1 
BrilliantColorTM0 - 2
*2 *4
*3
*1,*6 
*8
HIGH BRIGHTNESS
SPORTS, VIDEO, CINEMA
AUTO , NTSC , PAL , SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60 AUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRETCH, REAL AUTO, SPORTS, VIDEO, CINEMA
PASSWORD FUNCTION
SCART INPUTSET UP INSTALLATION
FEATURECOLOR TEMP.
VERT.POSITIONSTANDARD, LOW
OFF,  5,  10,  15,  30,  60min
AUTO, RGB, YC
BCR / YPBPR
ON , OFF
IMAGE REVERSE SPLASH SCREEN
BLUE, BLACK BACK COLOR
OFF, MIRROR, INVERT, MIRROR INVERT
AUTO, OFF *8 
WXGA
* 6: Not available when the input signal is from the HDMI IN terminal. 
* 7: Available only when the input signal is 480i, 480p, 576i, or 576p.
* 8: Available only when the input signal is from the COMPUTER IN/COMPONENT VIDEO IN terminal.  
						

							EN-24 How to set the menus:
The following describes how to set AUTO POWER OFF 
time as an example. 
1.  Press the MENU button. 
•  When no signal is applied, the menu would not 
appear. 
2. Press the 
 or 
 button to select a menu to use.  
3.  Press the ENTER button (or 
 button).
IMAGE
SVGA60opt.
AV MEMORY 1
INSTALLATION
SVGA60opt.
AV MEMORY 1
SCREEN SIZE
INSTALLATION
SVGA60
WXGA (15:9)
VERTICAL LOCATION0
opt.
AV MEMORY 1
4. Press the 
 or 
 button to select an item to ad-
just. 
5.  Set the selected item by pressing the 
 or 
 but-
ton. 
To cancel the menu:
6.  Press the MENU button several times. 
Important:
•  When the MENU button doesn’t function,  unplug 
the power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again. 
•  After selecting the items marked with 
, press the 
ENTER button.
OFF AUTO POWER 
ONOFFAUTO POWER 
OFF
30 min AUTO POWER 
ONOFFAUTO POWER 
OFF
CONTRAST
IMAGE
0
BRIGHTNESS 0
0
COLOR
10
SVGA60
TINT
0SHARPNESS
COLOR TEMP.
BrilliantColorTM
opt.
AUTOGAMMA MODE
AV MEMORY 1
6500K
IMAGE
REVERSE
OFF OFF
SCREEN SIZE
BACK COLOR
OFF
TEST PATTERN
CROSS HATCH
SVGA60
720P(16:9)VERTICAL 
LOCATION0
opt.
STANDARD LAMP MODE
AV MEMORY 1
AUTO POWER
ON
AUTO POWER
OFF
INSTALLATION
TRIGGER OUT
OFF
ONON
BLUE SPLASH
SCREEN
FEATURE
AUTO
SVGA60
AUTO AUTO
opt.
MENU POSITION
CINEMA MODE
VIDEO SIGNAL?
ASPECT
RESET ALL
English
LANGUAGEAË
OFF
AUTO
OK
DISPLAY INPUT PASSWORD
FUNCTION
1.
AV MEMORY 1
SET UP
AUTO WXGA
SCART INPUTWXGA
Available settings in the menus
Set the following items on their relevant menus.  
1. IMAGE menu  2. INSTALLATION menu  3. FEATURE menu
1. IMAGE menu
ITEM SETTING FUNCTION
GAMMA MODE  AUTO  The proper gamma mode is automatically selected depending on the input 
signal. Default is AUTO. 
  SPORTS  This is a bright mode suitable for watching sports images. 
  VIDEO  This is a standard mode suitable for watching video images etc. 
  CINEMA  This is a mode for watching movies in dim lighting as in a theater. 
 USER1 
 / USER2   Select to adjust the gamma curve. (See page 28.)
CONTRAST ±
30  Use to adjust the contrast of the projected image. (See page 27.)  
BRIGHTNESS ±
30  Use to adjust the brightness of the projected image. (See page 27.) 
COLOR TEMP. 
  5 options  Use to adjust the color temperature. (See page 28.) 
COLOR ±
10  Use to adjust the color thickness of the projected image. (See page 27.)
TINT ±
10  Use to adjust the color tint of the projected image. (See page 27.) 
SHARPNESS ±
5  Use to adjust the sharpness of the projected image. (See page 27.)
BrilliantColor
TM  0 - 2  Use to adjust the BrilliantColorTM function.  When set to 0, BrilliantColorTM 
doesn't work.
• BrilliantColor
TM uses BrilliantColorTM technology of Texas Instruments in USA. When you set this item to 1 or 2, the 
projector displays higher resolution images while reproducing superior colors. 
•  By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. (See 
page 26.)
Menu operation (continued) 
						

							EN-25
ENGLISH
2. INSTALLATION menu
ITEM SETTING FUNCTION
SCREEN SIZE 4 op
tions  Select according to the screen size.
VERTICAL LOCATION ±26  Use to adjust the position (height) of the projected image.
LAMP MODE  STANDARD  Select this option when you want to view images in a well-lit room.
  LOW  Select to moderate the intensity of the lamp. The fan operating sound is reduced 
and the lamp lifetime becomes longer. 
AUTO POWER ON  ON / OFF When ON is chosen, the lamp is automatically lit when the power cord is plugged 
in the wall outlet. Choose ON when using the projector mounted on the ceiling. 
•  The projector is in the stand-by mode when the lamp is off.  Use the remote 
control to turn on the lamp. 
  
AUTO POWER OFF  OFF / 5 - 60min Use to set the time elapsed before the projector enters the stand-by mode when 
there is no signal input from the source. 
SPLASH SCREEN   ON / OFF  Choose ON to display the splash screen when the power is turned on. BACK COLOR  BLUE / BLACK  Use to change the color of the screen that appears when no signal is supplied. IMAGE REVERSE  OFF  Select when viewing images from the front with the projector installed on the 
fl oor. 
  MIRROR  Select when viewing images projected from the behind of the screen with the 
projector installed on the fl oor.  
  INVERT  Select when viewing images projected from the behind of the screen with the 
projector installed on the ceiling. 
  MIRROR INVERT  Select when viewing images from the front with the projector installed on the 
ceiling.
TRIGGER OUT  ON /OFF  Choose ON to output the trigger output signal (12 V) from the TRIGGER terminal 
when the lamp illuminates. 
TEST PATTERN  CROSS HATCH 
  Select to show the test cross hatch pattern.
•  LAMP MODE can’t switch for 1 minute after the power ON.
•  When the lamp mode is switched, the projected image may fl icker. This is not a product malfunction.  
•  Do not change the setting of LAMP MODE frequently. 
•  To cancel the test pattern, press any button. 
3. FEATURE menu
ITEM SETTING FUNCTION
ASPECT  AUTO  Select to change the aspect ratio automatically depending on the input signal.
  4:3  Select to project images with an aspect ratio of 4:3. 
  16:9  Select to project images with an aspect ratio of 16:9. (Linearly stretched.)
  ZOOM1  Select to enlarge and project images of CinemaScope size. 
  ZOOM2  Select to enlarge and project images of Vista size. 
  STRETCH  Select to enlarge to 16:9 and project of the images with an aspect ratio of 4:3. 
(Non-linearly stretched.) 
  REAL  Select to project images in their original size as input. Not available when the 
keystone adjustment is applied.
PASSWORD FUNCTION   Use to enable or cancel the password lock. See page 30 for details.MENU POSITION   2 options  Use to change the position of the menu. 
CINEMA MODE AUTO The fi lm mode will be automatically activated when a fi lm source signal is input. 
 OFF The fi lm mode will not be activated. 
VIDEO SIGNAL  8 options When AUTO is selected, the appropriate video format is automatically selected 
depending on the input signal. If the image isn’t displayed correctly, select the 
desired video format manually.
WXGA  AUTO  Use to detect WXGA signal automatically.
  OFF  When a signal other than WXGA is input, it takes abnormally long time to 
display an image, or an image is not displayed correctly, select OFF.
SET UP  AUTO  Select AUTO for normal use. When LANGUAGE is not set to 
 and 480i, 
480p or TV60 signal is inputted, the SET UP changes to 7.5% automatically.
  OFF  Select to make black lighter. 
  3.75%/7.5%  Select to make black intense. 
•  When 7.5% is chosen, the brightness is decreased by set-up cancel func-
tion for U.S. Choose OFF when the image is dark.
SCART INPUT  ON /OFF  Choose ON when connecting the projector with a device equipped with the 
SCART terminal that can output RGB signal. SCART terminal is used mainly 
in Europe. Choose OFF normally. (Available only for the input signal from the 
COMPUTER IN/COMPONENT VIDEO IN terminal.)
LANGUAGE  10 languages  Use to select the language used in the menus. 
RESET ALL  OK 
  Use to reset the settings of the menu (excluding PASSWORD FUNCTION and 
LANGUAGE) to the factory setting values. 
•  To display images of WXGA signals, set WXGA in the FEATURE menu to AUTO. It takes a little while to display im-
ages of WXGA and XGA60 signals.
•  Some signals may not display images of WXGA signal correctly. See page 36 for details.
•  When SCART INPUT is set to ON, normal computer signals aren't projected. 
•  Use a SCART-BNC (or SCART-Mini D-SUB 15P) cable (option) when connecting this projector with an AV device 
equipped with the SCART terminal.
•  Some AV devices equipped with the SCART terminal aren't compatible with this projector.
•
  It may take a little while to carry out RESET ALL in the FEATURE menu. 
						

							EN-26
4. SIGNAL menu  5. USER menu
Menu operation (continued)
4. SIGNAL menu
ITEM SETTING FUNCTION
HORIZ. POSITION  0 - 999  Use to adjust the horizontal position of the projected image. 
VERT. POSITION  0 - 999  Use to adjust the vertical position of the projected image. 
FINE SYNC.  0 - 31 Use to eliminate fl ickering or blur, if it appears, while viewing the projected image. 
TRACKING  0 - 9999  Use to eliminate vertical wide stripes, if it appears, while viewing the projected 
image.
COMPUTER INPUT  AUTO  The proper setting is automatically selected.
  RGB  Select this option when connecting the projector to high defi nition video 
equipment having R, G, and B output terminals. 
 YC
BCR / YPBPR  Select this option when connecting the projector to a DVD player or other 
device having Y, C
B, and CR (or Y, PB, and PR) component video output terminals.
HOLD  OFF / ON
  Use to adjust the image when fl agging occurs near the top of the screen.
•  Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
•  When you change the horizontal or vertical position to a large extent, noise may appear. 
•  The adjustable range of the vertical position varies depending on the type of the input signal. Though the image 
may stay in the same position even when the setting value is changed, such symptom is not a malfunction.
5. USER menu
ITEM SETTING FUNCTION
CLAMP POSITION  0 - 255  Use to correct solid white or solid black in the projected image.
CLAMP WIDTH  1 - 63  Use to correct solid black in the projected image. 
VERT.SYNC  AUTO / OFF  Use to adjust the image when its motion doesn't run smoothly.  Select AUTO 
for normal use.
OVER SCAN  100 - 90%  Use to adjust the display area of the projected image when playing LD and 
DVD discs. 
LPF  ON / OFF  Use to select whether or not to enable the LPF.
SHUTTER (U)  0 - 38 
Use to display the black bar on the top part of the image.
SHUTTER (L)  0 - 38 Use to display the black bar on the bottom part of the image.
SHUTTER (LS)  0 - 95 Use to display the black bar on the left half of the image.
SHUTTER (RS)  0 - 95 Use to display the black bar on the right half of the image.
•  If you increase the OVER SCAN setting when viewing video signals, noise may appear on the screen. In this case, 
decrease the OVER SCAN setting.
•  When VIDEO or S-VIDEO is chosen as the source, OVER SCAN is not available with certain signals.
•  OVER SCAN is not available in the REAL mode.
AV memory
You can store up to 3 patterns of the image quality setting for each input source.
To store the settings
1.  Press an AV MEMORY button (M1, M2 or M3 ) on the remote control to store the settings.
2.  Set the items of the IMAGE menu.
•  The settings are automatically stored.
•  Setting the items by using the picture quality adjusting buttons on the remote control is also available.
To enable the stored image quality settings
1.  Press the AV MEMORY button to enable the stored setting.
•  The image quality settings stored in the selected memory is enabled.
•  When the input source is changed, the AV memory setting selected just before is automatically selected.
•  When RESET ALL in the FEATURE menu is selected, all the settings of the AV memory are cleared.
R G BR G B
SIGNAL
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTAUTO
FINE SYNC. 0
USER
SVGA60opt.
OK
ONHOLD
AV MEMORY 1CLAMP 
POSITION
USER
0
CLAMP WIDTH 1
OVER SCAN 100%
LPF OFF
SHUTTER (U) 0
SHUTTER (L) 0 VERT. SYNC AUTO
?
SHUTTER (LS) 0
SHUTTER (RS) 0 
						

							EN-27
ENGLISH
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the 
 or 
 button. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the 
 button is pressed, the image becomes brighter and more 
defi ned. Every time the 
 button is pressed, the image becomes darker and less defi ned.
BRIGHTNESS
Every time the 
 button is pressed, the image becomes brighter. Every time the 
 button is pressed, the image 
becomes darker. 
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR or TINT by pressing the 
 or 
 button.  
•  COLOR is unavailable when the COMPUTER or HDMI is selected as the input source. 
•  TINT is available only when the NTSC signal is input. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
COLOR 
Use to adjust the color intensity of the projected image. Every time the 
 button is pressed, the color intensity 
increases. Every time the 
 button is pressed, the color intensity decreases. 
•  COLOR is unavailable when the COMPUTER or HDMI is selected as the input source. 
TINT
Use to adjust the tint of the projected image. Every time the 
 button is pressed, the image appears more greenish.  
Every time the 
 button is pressed, the image appears more reddish. 
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select SHARPNESS by pressing the 
 or 
 button. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button.  
						

							EN-28
To adjust the tone of white (COLOR TEMP.): 
You can select a preset color temperature (white tone) using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select COLOR TEMP.  by pressing the 
 or 
 button. 
3.  Select your desired color temperature by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the tone of white (To customize the color temperature): 
To customize (and store) the color temperature to your preference, carry out the following procedure. 
(See page 24 for menu setting.) 
1.  Select COLOR TEMP. in the IMAGE menu. 
2. Press the 
 or 
 button to select USER 
. 
3.  Press the ENTER button.
4. Press the 
 or 
 button to select the desired item. 
5. Press the 
 or 
 button to adjust the selected item. 
6.  Repeat steps 4 and 5 for optimum adjustment results.
To cancel the menu:
7.  Press the MENU button. 
To enable the stored color temperature: 
1.  Select USER by pressing the COLOR TEMP button on the remote control. 
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. White of which 
temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can 
change the color temperature using the following procedures. 
To rise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
•  If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can't be 
obtained even when you maximize CONTRAST in the IMAGE menu. 
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST G 0
BRIGHTNESS G 0
BRIGHTNESS B 0
CONTRAST B 0
BRIGHTNESS R 0
To adjust the ratio of change in brightness (GAMMA MODE): 
You can select a preset gamma mode using the menu. 
(See page 24 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select GAMMA MODE by pressing the 
 or 
 button. 
3.  Select your desired gamma mode by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
To adjust the original ratio of change in brightness (To customize the gamma mode): 
To customize (and store) the gamma mode to your preference, carry out the following procedure. 
(See page 24 for menu setting.) 
1.  Select GAMMA MODE in the IMAGE menu. 
2. Press the 
 or 
 button to select USER1 
 or USER2 . 
3.  Press the ENTER button.
4. Press the 
 or 
 button to select REFERENCE.
5. Press the 
 or 
 button to select basic gamma curve. 
•  Generally, select the most preferable gamma curve from the preset gamma curve.
6. Press the 
 or 
 button to select the desired item. 
 HIGH  : Use to adjust the gradation of the bright scenes.
 MID   : Use to adjust the gradation of the medium brightness scenes.
 LOW   : Use to adjust the gradation of the dark scenes.
7. Press the 
 or 
 button to adjust the selected item. 
8.  Repeat steps 6 and 7 for optimum adjustment results.
To cancel the menu:
9.  Press the MENU button. 
To enable the stored gamma mode: 
1.  Select USER1 or USER2 by pressing the GAMMA button on the remote control. 
•  Change in the brightness may be hard to recognize in some images. 
Adjusting projected images (continued)
REFERENCE
GAMMA MODE-USER1
CINEMA
0
0
0
HIGH
MID
LOW 
						

							EN-29
ENGLISH
This projector automatically and properly projects video signals supplied from the computer. However, some video 
signals may not be projected, depending on the type of the computer. In such a case, press the AUTO POSITION 
button. (See page 22.) When the signal is still not projected properly, adjust the projected image using the SIGNAL 
menu. 
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image fl ickers. 
The projected image is blurred. ………………………… Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally.   ……… Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to the right. Every time 
the 
 button is pressed, the image moves to the left. 
The projected image is displaced vertically.   ………… Adjust VERT.POSITION in the SIGNAL menu. Every time the 
 
button is pressed, the image moves down. Every time the 
 
button is pressed, the image moves up. 
The top part of the image fl ags.  ………………………Change the setting of HOLD in the SIGNAL menu. Select ON , 
press the ENTER button, and adjust BEGIN or END to minimize 
the fl agging.
Wide strips appear.  ……………………………………… Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - 
USER menu.
The motion doesn't run smoothly. ……………………… Adjust VERT. SYNC. in the SIGNAL - USER menu.  Select 
AUTO for normal use. 
Noise appears on the right or left half of the image.
 …Adjust SHUTTER (LS) or SHUTTER (RS) in the SIGNAL - USER 
menu.
Noise appears on the top or bottom part of the image.
 …Adjust SHUTTER (U) or SHUTTER (L) in the SIGNAL - USER 
menu.
1.  Display the SIGNALmenu. 
2. Press the 
 or 
 button to select an item to adjust. 
3.  Adjust the selected item by pressing the 
 or 
 button. 
To cancel the menu:
4.  Press the MENU button. 
•  Do not change the settings of the SIGNAL menu in normal use. 
Simple method to adjust the image position
To adjust the horizontal position: 
1.  Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the 
right edge of the image with the right side of the screen by adjusting TRACKING. 
2.  Repeat step 1 above to complete the adjustment of the horizontal position. 
To adjust the vertical position: 
3.  Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION. 
LPF 
You can select whether or not to enable the LPF. This item is set to OFF normally. 
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or 
game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected 
images become softened slightly. 
                                                                                                                                                         
1.  Display the SIGNAL menu. 
2. Press the 
 or 
 button to select USER. 
3.  Press the ENTER button.
4. Press the 
 or 
 button to select LPF. 
5. Press the 
 or 
 button to choose ON or OFF. 
To cancel the menu:
6.  Press the MENU button.
LPF OFF 
						

							EN-30
DISPLAY INPUTLOCK
UNLOCKOKOK
PASSWORD
CONFIRM
O K CANCEL
DISPLAY INPUTLOCK
UNLOCKOKOK
PASSWORD
O K CANCEL
Password function
This projector is equipped with the password function 
that is designed for prevention of theft and wrong op-
eration by children and restriction on operation by other 
than specifi ed users. The password function has two 
modes as follows. 
DISPLAY INPUT ...........When the projector is turned 
on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is entered. 
When the password is entered, the startup screen 
will switch to the regular operation screen.
MENU ACCESS ............All the buttons except for the 
POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You can 
use this mode as a measure of prevention of wrong 
operation by children and restriction on operation by 
other than specifi ed users.
To enable the password function:
1.  Display the FEATURE menu.
2. Press the 
 or 
 button to select PASSWORD 
FUNCTION.
3. Press the  button to change the mode among DIS-
PLAY INPUT and MENU ACCESS.
•  When the password has already been set, the 
mode won't be changed. In such cases, press the 
ENTER button to cancel the password function 
and try again. 
4.  Press the ENTER button.
•  The screen for setting the password function will 
appear. 
5.  Press the ENTER button.
•  The screen for entering a password will appear. 
6. Press the 
 or 
 button to select a number from 0 
to 9.
7. Press the 
 button.
•  You can set the next digit. 
8.  Repeat steps 6 and 7 to set a four-digit password. 
9.  Enter the password again for confi rmation using the 
same steps.
10. Select OK, and press the ENTER button. 
•  If the entered passwords don’t match, an error 
message will appear. 
•  To cancel the procedure, select CANCEL and 
press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. To cancel the password function: 
1.  Display the FEATURE menu.
2. Press the 
 or 
 button to select PASSWORD 
FUNCTION.
3.  Press the ENTER button.
•  The screen for canceling the password function 
will appear.
4.  Press the ENTER button.
•  The screen for entering the password will 
appear. 
5. Press the 
 or 
 button to select a number from 0 
to 9.
6. Press the 
 button.
•  You can set the next digit. 
7.  Repeat steps 5 and 6 to enter the four-digit 
password. 
8. Press the 
 button, select OK, and press the 
ENTER button.
•  If you enter a wrong password, an error message 
will appear.
•  To cancel the procedure, press the 
 button, 
select CANCEL, and press the ENTER button. 
•  You can cancel the procedure by pressing the 
MENU button alternatively. 
Important:
•  If you forget your password, hold down the MENU 
and ENTER buttons on the control panel at the 
same time about three seconds to cancel the 
password function.
Advanced features