Mitsubishi Hc6800 Projector User Manual

							EN-31
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu.
(See page 26 for menu setting.)Display the IMAGE menu.
1. 
Select CONTRAST or BRIGHTNESS by pressing the 
2.  p or q button.
Adjust the selected item by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button.
4. 
CONTRAST
Select to adjust the contrast of the image. Every time the u button is pressed, the image becomes brighter and more 
defined. Every time the t button is pressed, the image becomes darker and less defined.
BRIGHTNESS
Every time the u button is pressed, the image becomes brighter. Every time the t button is pressed, the image 
becomes darker.
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu.
(See page 26 for menu setting.)
Display the IMAGE menu.
1. 
Select COLOR or TINT by pressing the 
2.  p or q button.
Adjust the selected item by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button.
4. 
COLOR
Use to adjust the color intensity of the projected image. Every time the  u button is pressed, the color intensity 
increases. Every time the t button is pressed, the color intensity decreases.
TINT
Use to adjust the tint of the projected image. Every time the u button is pressed, the image appears more greenish. 
Every time the t button is pressed, the image appears more reddish.
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu.
(See page 26 for menu setting.)
Display the IMAGE menu.
1. 
Select SHARPNESS by pressing the 
2.  p or q button.
Adjust the selected item by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button. 
4. 
Adjusting projected images 
						

							EN-32
To adjust the tone of white (COLOR TEMP.):
You can select a preset color temperature (white tone) using the menu.
(See page 26 for menu setting.)Display the IMAGE menu.
1. 
Select COLOR TEMP. by pressing the 
2.  p or q button.
Select your desired color temperature by pressing the 
3.  t or u button.
The color temperature of each option is as follows: 
COOL: Approx. 9300K, MEDIUM: Approx. 6500K (D65), WARM: Approx. 5800K.
To cancel the menu: Press the MENU button.
4. 
To adjust the tone of white (To customize the color temperature):
To customize (and store) the color temperature to your preference, carry out the following procedure.
(See page 26 for menu setting.)
Select COLOR TEMP. in the IMAGE menu.
1. 
Press the 
2.  t or u button to select USER 
.
Press the ENTER button.
3. 
Press the 
4.  p or q button to select REFERENCE.
Press the 
5.  t or u button to select basic color temperature.
Generally, select the most preferable 
•	 color temperature from the preset 
color temperature.
Press the 
6.  p or q button to select the desired item.
Press the 
7.  t or u button to adjust the selected item.
Repeat steps 6 and 7 for optimum adjustment results.
8. 
To cancel the menu:
Press the MENU button.
9. 
To enable the stored color temperature:
Select USER 
1. 
 by pressing the COLOR TEMP. button on the remote control. 
Adjusting projected images (continued)
About color temperature
There are different kinds of white color. Color temperature is a way to show the differences in white. White of which 
temperature is low appears reddish. When the color temperature rises, white appears bluish. For example, you can 
change the color temperature using the following procedures.
To rise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
If you set all of CONTRAST R, G, and B to negative values, the original \
brightness of the image can’t be 
•	
obtained even when you maximize CONTRAST in the IMAGE menu. 
CONTRAST R
COLOR TEMP. - USER
0
CONTRAST G 0
BRIGHTNESS G0
BRIGHTNESS B0
CONTRAST B0
BRIGHTNESS R0
REFERENCEMEDIUM
To optically brighten or darken projected images (AUTO IRIS): 
Iris is a function to optically adjust the contrast by opening or closin\
g the aperture of the lamp. This projector is 
equipped with the following 2 modes to adjust the iris.
AUTO
The iris is automatically adjusted depending on the image being displaye\
d. AUTO mode has 5 types as follows.
Mode 1:  When white objects are displayed in an overall dark scene, rich black details can be obtained\
. (This mode is 
suitable for displaying live images.)
Mode 2: White appears more brilliant than that in Mode 1. 
Mode 3: Images appear brighter than those in Mode 2. 
Mode 4:   This mode is recommended when you have been using a standard lamp and its operating time exceeds 
2000 hours based on that LAMP MODE is LOW. (See page 30.)
Mode 5: This mode provides deeper blacks than the other modes. 
OFF
The iris is kept fully opened.  
						

							EN-33
Adjusting projected images (continued)
To adjust the ratio of change in brightness (GAMMA MODE):
You can select a preset gamma mode using the menu.
(See page 26 for menu setting.)Display the IMAGE menu.
1. 
Select GAMMA MODE by pressing the 
2.  p or q button.
Select your desired gamma mode by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button.
4. 
To adjust the original ratio of change in brightness (To customize the gamma mode):
To customize (and store) the gamma mode to your preference, carry out the following procedure.
(See page 26 for menu setting.)
Select GAMMA MODE in the IMAGE menu.
1. 
Press the 
2.  t or u button to select USER1 
 or USER2 .
Press the ENTER button.
3. 
Press the 
4.  p or q button to select REFERENCE.
Press the 
5.  t or u button to select basic gamma curve.
Generally, select the most preferable gamma curve from the preset gamma 
•	
curve.
Press the 
6.  p or q button to select ADJUST MODE.
Press the 
7.  t or u button to adjust mode of gamma curve (ALL, RED, GREEN, or BLUE).
Select whether to adjust RED, GREEN, and BLUE collectively or separately\
. 
•	
Press the 
8.  p or q button to select the desired item.
HIGH  :  Use to adjust the gradation of the bright scenes. (The values displayed\
 correspond to RED,   
    GREEN, and BLUE from the left respectively.)
MID  :  Use to adjust the gradation of the medium brightness scenes. (The value\
s displayed correspond   
    to RED, GREEN, and BLUE from the left respectively.)
LOW   :  Use to adjust the gradation of the dark scenes. (The values displayed c\
orrespond to RED,   
    GREEN, and BLUE from the left respectively.)
Press the 
9.  t or u button to adjust the selected item.
Repeat steps 6 - 9 for optimum adjustment results.
10. 
To cancel the menu:
Press the MENU button.
11. 
To enable the stored gamma mode:
Select USER1 or USER2 by pressing the GAMMA button on the remote control.
1. 
Change in the brightness may be hard to recognize in some images.
•	
Noise reduction
This projector has the following noise reduction functions. However, these functions don’t work with 720p, 1080i, and 
1080p signals and signals supplied from computer. 
TRNR (temporal recursive noise reduction)
Reduces random noise appearing in projected images. Adjust the reduction level using the  t or u button. 
MNR (mosquito noise reduction) 
Reduces mosquito noise appearing around sharp edges in DVD images. Adjust the reduction level using the  t or u 
button. 
BAR (block artifact removal)
Reduces block noise or mosaic-like patterns appearing in DVD images. Turn on this function using the  t or u 
button. 
REFERENCE 
GAMMA MODE - USER1
VIDEO 
0
0
0
0
0
0
HIGH
MID
LOW
ALLADJUST MODE
0
0
0 
						

							EN-34
This projector automatically and properly projects video signals supplied from the computer. However, some video 
signals may not be projected, depending on the type of the computer. In such a case, press the AUTO POSITION 
button. (See page 24.) When the signal is still not projected properly, adjust the projected image using the SIGNAL 
menu.
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms.
Wide strips appear. .........................................................Adjust TRACKING in the SIGNAL menu.
The projected image flickers.
The projected image is blurred. ...................................... Adjust FINE SYNC. in the SIGNAL menu.
The projected image is displaced horizontally.  ............. Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
t button is pressed, the image moves to the right. Every time 
the u button is pressed, the image moves to the left.
The projected image is displaced vertically. .................. Adjust VERT.POSITION in the SIGNAL menu. Every time the t  button is pressed, the image moves down. Every time the u 
button is pressed, the image moves up.
The top part of the image flags. .....................................
Change the setting of HOLD in the SIGNAL menu. Select ON , 
press the ENTER button, and adjust BEGIN or END to minimize 
the flagging.
A solid black or solid white appears in the image.  ........ Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - 
USER menu.
The motion doesn’t run smoothly. .................................. Adjust VERT. SYNC. in the SIGNAL - USER menu. Select 
AUTO for normal use.
Noise appears on the right or left half of the image. ...... Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL - USER 
menu.
Noise appears on the top or bottom part of the image. . Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER 
menu.
Display the SIGNAL menu.
1. 
Press the 
2.  p or q button to select an item to adjust.
Adjust the selected item by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button.
4. 
Do not change the settings of the SIGNAL menu in normal use.
•	
Simple method to adjust the image position
To adjust the horizontal position:
Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the 
1. 
right edge of the image with the right side of the screen by adjusting TRACKING.
Repeat step 1 above to complete the adjustment of the horizontal positio\
n.
2. 
To adjust the vertical position:
Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION. 
3. 
LPF (Progressive filter)
You can select whether or not to enable the LPF.
Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player you 
use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected images become 
softened slightly.
Adjusting projected images (continued) 
						

							EN-35
Password function
This projector is equipped with the password function 
that is designed for prevention of theft and wrong 
operation by children and restriction on operation by 
other than specified users. The password function has 
two modes as follows.
DISPLAY INPUT .......... When the projector is turned on, the startup screen (or splash screen) will appear 
and stay on the screen until the password is 
entered. When the password is entered, the startup 
screen will switch to the regular operation screen.
MENU ACCESS ........... All the buttons except for the  POWER button on the projector are disabled. (The 
buttons on the remote control are enabled.) You 
can use this mode as a measure of prevention 
of wrong operation by children and restriction on 
operation by other than specified users.
To enable the password function: Display the FEATURE menu.
1. 
Press the 
2.  p or q button to select PASSWORD 
FUNCTION.
Press the 
3.  u button to change the mode among 
DISPLAY INPUT 
 and MENU ACCESS .
When the password has already been set, the 
•	
mode won’t be changed. In such cases, press 
the ENTER button to cancel the password 
function and try again.
Press the ENTER button.
4. 
The screen for setting the password function will 
•	
appear.
DISPLAY INPUTLOCK
UNLOCK OKOK
Press the ENTER button.
5. 
The screen for entering a password will appear.
•	
PASSWORD
CONFIRM
1
324
O K : ENTER CANCEL : MENU
Enter a 4 - 8 digit password using the 
6. p, u, q or 
t
 buttons on the remote control as shown below.
(
p=1, u=2, q=3, t =4) 
Press the ENTER button.
7. 
To cancel the procedure, press the MENU 
•	
button. 
Enter the password again for confirmation using the 
8. 
same steps.
Press the ENTER button. 
9. 
If the entered passwords don
•	 ’t match, an error 
message will appear. 
To cancel the procedure, press the MENU 
•	
button. 
Advanced features
To cancel the password function:
Display the FEATURE menu.
1. 
Press the 
2.  p or q button to select PASSWORD 
FUNCTION.
Press the ENTER button.
3. 
The screen for canceling the password function 
•	
will appear.
DISPLAY INPUT LOCK
UNLOCK OKOK
Press the ENTER button.
4. 
The screen for entering the password will 
•	
appear.
PASSWORD
1
324
O K : ENTER CANCEL : MENU
Enter a 4 - 8 digit password using the 
5. p, u, q or 
t
 buttons on the remote control as shown below.
(
p=1, u=2, q=3, t =4) 
Press the ENTER button.
6. 
If you enter a wrong password, an error 
•	
message will appear.
To cancel the procedure, press the MENU 
•	
button. 
Important: Disable the password by pressing the MENU and 
•	
ENTER buttons on the control panel at the same 
time about three seconds.
Kensington Lock
This projector has a Kensington Security Standard 
connector for use with Kensington MicroSaver 
Security System. Refer to the information that came 
with the Kensington System for instructions on how 
to use it to secure the projector. Please contact 
Kensington Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700
Fax: +1- (650)572-9675 
						

							EN-36
This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness 
may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the 
lamp with a new lamp sold separately that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Spare lampVLT-HC6800LP
Warning: Be careful not to drop the lamp fixing screws inside of the projector. Don’t put a metal piece or flammable object 
•	
into the projector. Using the projector with any foreign object present inside may result in electric shock or fire. 
When you can’t remove the foreign object from the inside, contact your dealer for removal.
Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation 
•	
may also result in fire.
Don’t shake the removed lamp or don’t lift it above your face. Your eyes may be injured by flying or falling glass 
•	
fragments.
Don’t replace the lamp immediately after use because the lamp cover will be ver\
y hot. You may get burned. Turn 
•	
off the power using the POWER button. After the lamp goes out, wait about \
two minutes until the intake and 
exhaust fans for cooling the lamp stop rotating. Then turn off the main power switch, unplug the power cord, and 
wait at least 1 hour to allow the lamp to cool down enough to the touch.\
Do not touch the lamp directly. It may break and cause injury or burn.
•	
Interval of lamp replacement
The recommended interval of lamp replacement is about 4000 hours*1*2 of consecutive use. Such interval differs 
depending on the operating environment and may be shorter than 4000 hours*1*2. Decrease in luminescence and/or 
color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3000 hours*1, 
the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator 
will be lit red only) and the lamp replacement message will appear on the screen for one minute everytime the lamp 
is turned on. When the lamp has been used for about 3800 hours*
1, the replacement message (LAMP EXCHANGE) 
will appear on the screen for one minute every 20 hours*1 thereafter. When the lamp operation time exceeds 4000 
hours*1*2, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp 
operation time is reset.
*1:  Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be 
shorted.
*2:  When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
Caution: Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a 
•	
breakdown.
This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may 
•	
explode or fail to illuminate permanently because of an impact, scratch,\
 or deterioration through use. The period 
of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on 
operation conditions. Therefore, the lamp may explode soon after the start of use.
The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction 
•	
of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting \
normally.
When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the l\
amp box and 
•	
the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains 
mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it 
should enter your eye or mouth, see a doctor immediately.
In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the 
•	
projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace 
the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the 
•	
projector or option lamp to prevent glass fragments from scattering.
Be sure to use the lamp exclusive to this projector, VLT-HC6800LP. Use of other lamps may cause a failure of the 
•	
projector.
Replacing the lamp 
						

							EN-37
Replacing the lamp (continued)
To replace the lamp:
Turn off the main power switch and unplug the 
1. 
power cord.
Loosen two screws (a) using a Phillips screwdriver 
2. 
(+) and remove the left side panel from the 
projector.
(a)
Loosen the screw (b) using a Phillips screwdriver 
3. 
(+), and remove the lamp cover (c).
(b) (c)
Loosen the screws (d) using a Phillips screwdriver 
4. 
(+).
(d)
Pull the handle.
5. 
Pull out the lamp box by the handle while holding 
6. 
the projector.
Pull the lamp box out of the projector slowly. 
•	
If it is pulled out quickly, the lamp may break 
scattering glass fragments.
Do not spill liquid on the removed lamp box or 
•	
do not place it near any flammable object or 
where children can reach to prevent injury or 
fire.
Load a new lamp box securely into the projector in 
7. 
the right orientation.
Put the handle back to the original position.
8. 
Make sure that the handle is locked.
•	 Tighten up the screws (d) using a Phillips 
9. 
screwdriver (+).
(d)
Tighten up the screw (b) using a Phillips 
10. 
screwdriver (+) to secure the lamp cover (c).
(b) (c)
Attach the left side panel to the projector and fix it 
11. 
with two screws (a).
(a)(a)
Reset of the lamp operation time
Plug the power cord into the wall outlet and turn on 
12. 
the main power switch.
Hold down the 
13.  t, u, and POWER buttons on the 
control panel at the same time about 3 seconds.
Important: Unless these 3 buttons are 
•	 held down at the same 
time, the lamp operation time isn’t reset. 
Make sure that the STATUS indicator blinks twice 
•	
and the lamp operation time is reset successfully.
The projector doesn’t turn on if the lamp cover isn’t 
•	
attached securely.
Be sure to reset the lamp operation time whenever 
•	
you replace the lamp.
Do not reset the lamp operation time unless you 
•	
replace the lamp.
The lamp is fragile. If it is broken, be careful not to 
•	
cut yourself with glass fragments.
Caution:This projector uses a lamp that 
•	
contains mercury. Disposal of the lamp 
or the projector with the lamp may 
be regulated due to environmental 
considerations. For disposal or 
recycling information, please contact 
your local authorities or the Electronic 
Industries Alliance: www.eiae.org. (For 
the U.S. only.) 
						

							EN-38
When removing the lamp from the ceiling-mounted projector
When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the 
projector or option lamp to prevent glass fragments from scattering.Assemble the lamp replacement tray according to the procedure shown on it.
•	
Follow steps 1 to 5 on page 37.
1. 
Attach the lamp replacement tray to the projector as shown in the 
2. 
figure.
Secure the lamp replacement tray on the projector using the tape 
3. 
packed with the tray.
Pull out the lamp box by the handle while holding the projector.
4. 
Hold the lamp replacement tray to prevent glass fragments 
•	
from scattering.
Don’t put the lamp directly on the lamp replacement tray 
•	
because it may fall.
Detach the lamp replacement tray together with the removed 
5. 
lamp.
Follow steps 7 to 13 on page 37.
6. 
Replacing the lamp (continued)
Tape 
						

							EN-39
Warning:Never use flammable air duster or other materials when cleaning the ai\
r-filter. Flammable substances may ignite 
•	
causing fire or breakdown when the lamp is illuminated.
Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning the projector body 
•	
and lens. Flammable substances may ignite causing fire or breakdown while the lamp is illuminating.
Caution:
Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on 
the projector.
Cleaning of the air-filter
Clean the air-filter frequently (about once a month). If the air-filter or ventilation grilles become clogged with dirt or 
dust, the temperature inside the projector may rise and cause troubles, such as damage to the inside parts and 
shortening the life of the panels. When the temperature inside the projector rises, the STATUS 
•	
indicator will blink orange and the lamp will be turned off.
Loosen two screws that are fixing the right side panel using a 
1. 
Phillips screwdriver (+) and remove the panel from the projector. 
Remove the filter from the right side panel.
2. 
(1)  Remove the holder by pushing the tab of the holder on the air-filter in the direction of the arrow.
(2)  Remove the air-filter (white), spacer, and air-filter (gray).
Clean dirt and dust adhering to the air-filter using a vacuum.
3. 
For the air-filter (white) 
•	
If stubborn stains persist, wash the air-filter with water 
and dry well in the shade.
For the air-filter (gray) 
•	
If stubborn stains persist, wash the air-filter with diluted 
detergent, rinse with water, and dry well.
Attach the filter to the right side panel.
4. 
(1)  Attach the air-filter (gray), spacer, and air-filter (white) to the side panel, aligning their notches with that of the side panel. 
(2)  Insert the right tab of the holder to the side panel and push the  left tab in the direction of the arrow to attach the side panel.
Attach the right side panel to the projector and fix it with two 
5. 
screws. 
Important: If the air-filter is damaged or becomes extremely dirty, change it 
•	
with a new air-filter. Contact your dealer for a new air-filter.
Use the dedicated air-filter only.
•	
Caution:
Be sure to use the projector with an air-filter. If not, dust may get inside the projector causing fire and failure.
Cleaning of the projector and the ventilation slots
Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft 
cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.
To protect the surface of the projector from fading or deteriorating:
Do not spray insecticide on or inside the projector.
•	
Do not use benzine or thinner to clean it.
•	
Do not let rubber or plastic materials contact with projector.
•	
Cleaning of the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens clean\
ing fluid. The lens surface is 
fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens w\
ith your fingers.
Maintenance
Air-filter (gray)
Spacer
Air-filter (white)
Holder
Back of the right 
side panel
Holder
Fixing screws Right side 
panel
Fixing screws 
						

							EN-40
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be 
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
ProblemSolution
Power can not be 
turned on. Check whether the indicators are on or off and how they are lightning.
•	
POWER STATUS Solution
OffOff
Connect the power cord to the projector.
•	
Plug the power cord into a wall outlet.
•	
Turn on the main power switch.
•	
Steady red
Off
If any objects are blocking the air inlet or outlet grill, re move them and carry out the 
•	
following.
Turn off the main power switch.
1. 
Make sure that the projector has cooled off. 
2. 
Turn on the main power switch.
3. 
Press the POWER button.
4. 
Blinking 
orange
If any objects are blocking the air inlet or outlet grille, remove them.
•	
Don’t expose the air outlet grilles to hot air emitted from a heating appliance.
•	
Check whether the filter is clogged with dirt or dust.
•	
Clean the filter, if clogged. (See page 39.)
 

Blinking 
green
After the STATUS indicator stops blinking, press the POWER button.
•	If the main power switch is turned off while the fan is rotating, the lamp may not turn on about 1 
•	
minute when the main power switch is turned on next time.
The lamp can’t turn on again for one minute after it goes out.
•	
Press the POWER button several times.
•	
Steady redReplace the lamp. (The lamp is at the end of its life.)
•	
Blinking 
red/green
OffAttach the lamp cover.
•	
Steady
or 
 
Blinking
Unplug the power cord from the wall outlet and contact your dealer .
•	
No image appears on 
the screen.  Check that the lens cap is removed.
•	
It may take about one minute for the lamp to light up.
•	
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes 
•	
and then try again.
If the projector was turned off before the lamp was cooled down sufficiently last time, 
•	
the fan may start rotating and the POWER button may not work after the main power 
switch is turned on. After the fan stops rotating, press the POWER button to turn back 
on the POWER indicator.
Check that the intake vent is clean.
•	
Set SCART INPUT in the FEATURE menu to OFF. (See page 28.)
•	
Check that the lamp cover is closed. (See page 37.)
•	
Check that the cables connected to the external devices are not broken.
•	
When an extension cable is being used, replace it with the supplied cable for check. 
•	
When images are displayed correctly, add an RGB signal amplifier to the extension 
cable.
Check the operation manual of the video device for its connection.
•	
Power turns off. This problem may occur when the intake vent and/or exhaust vents are blocked. (In 
•	
such a case, the STATUS indicator brinks orange.)Remove the objects blocking the intake vent and/or exhaust vents and the\
n carry 
 

out the following procedure.
Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator 
1. 
goes out.)
Turn off the main power switch.
2. 
Wait at least 10 minutes.
3. 
Turn on the main power switch.
4. 
Press the POWER button.
5. 
When the STATUS indicator is steady red, it is indicating that the lamp should be 
•	
replaced. Replace the lamp in this case.
Check that AUTO POWER OFF has been set to OFF.
•	
If the lamp has deteriorated, it may go out after a while it illuminates\
.
•	
Troubleshooting