Mitsubishi Hc6800 Projector User Manual

							EN-21
How to change the settings:
With the remote control:Press the ASPECT button.
1. 
The screen for selecting the aspect ratio appears.
•	
Select your desired aspect ratio by pressing the 
2.  t or u button.
The aspect mode is switched between AUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRET\
CH, ANAMORPHIC1 and 
•	
ANAMORPHIC2.
Some modes are not available with certain signals.
•	
With the FEATURE menu:
(See page 26 for menu setting.) Display the FEATURE menu.
1. 
Select ASPECT by pressing the 
2.  p or q button.
Select your desired aspect ratio by pressing the 
3.  t or u button.
To cancel the menu: Press the MENU button.
4. 
Important:
When a 4:3 or 2.35:1 (CinemaScope) image is kept displayed for a long \
time before displaying 16:9 image, the 
•	
afterimages of the black bars may appear on the 16:9 image screen. (See page 41.)
FE A TURE 
AUTO
AUTO AUTO
opt.
MENU POSITION
CINEMA MODE
VIDEO SIGNAL
?
ASPECT
RESET ALL
English
LANGUAGEAË
OFF
AUTO
OK
DISPLAY
INPUT
PASSWORD
FUNCTION
1.
MENU DIMMER
A V MEMO R Y 1 
SETUP
SCART INPUT
OFF
Viewing video images (continued) 
						

							EN-22
2
1
A. Connecting the projector to a computer
Preparation: Make sure that the power of the projector and that of the computer are turned off.
•	
When connecting the projector to a desktop computer, disconnect the RGB cables that are connected to the 
•	
monitor. 
Connect one end of the supplied RGB cable to the 
1. 
COMPUTER IN/COMPONENT VIDEO IN terminal of the 
projector.
Connect the other end of the RGB cable to the monitor 
2. 
port of the computer.
Additional devices, such as a conversion connector and an 
•	
analog RGB output adapter, are required depending on the 
type of the computer to be connected.
When viewing images supplied from an analog-connected 
•	
computer, press the COMPUTER button on the remote 
control.
Turn on the power of the projector before that of the computer.
•	
Additional devices, such as a conversion connector and an analog RGB out\
put adapter, are required depending 
•	
on the type of the computer to be connected.
Use of a long cable may decrease the quality of projected images.
•	
Also read the instruction manual of the equipment to be connected.
•	
Images may not be projected correctly, depending on the type of the computer connected.
•	
Contact your dealer for details of connection.
•	
About DDC
The COMPUTER IN/COMPONENT VIDEO IN terminal of this projector complies with the DDC1/2B standard and the 
HDMI IN-1 and HDMI IN-2 terminals comply with the DDC2B standard. When a computer supporting this standard 
is connected to this terminal, the computer will automatically load the \
information from this projector and prepare for 
output of appropriate images.
When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector 
•	
before starting the computer. 
B. Plugging the power cord
Plug the power cord in the same way as described in “Viewing video images.” (See pa\
ge 17.)
To monitor port
COMPUTER IN/
COMPONENT VIDEO IN
RGB cable
Viewing computer images 
						

							EN-23
Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 
1. 
If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating 
•	
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks 
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
Turn on the power of the connected computer. 
2. 
Press the POWER button on the projector or ON ( I ) button on the remote control.
3. 
It may take about one minute for the lamp to light up.
•	
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
•	
Do not cover the lens with the lens cap while the lamp is on. 
•	
After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a 
•	
product malfunction.
The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP 
•	
MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
The projector starts warming up when the POWER button is pressed. During the warm-up process, images 
•	
may appear dark and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
•	
the STATUS indicator blinks red. (See page 43.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
4. 
Adjust with the 
5.  t or u button to get a fine picture.
When the ENTER button is pressed while “FOCUS” is displayed, the adjustment mode is switched \
between 
•	
FAST and STEP. When FAST is selected, the speed of focus controlled by the t or u button becomes fast, 
and it becomes slow when STEP is selected.
Select an input source.
6. 
Press the HDMI/COMPUTER button on the projector or the COMPUTER button on the remote control to select 
•	
COMPUTER.
The input source is switched between COMPUTER, HDMI1 and HDMI2 every time you press the HDMI/
•	
COMPUTER button on the projector.
Though it may take some time before an image is displayed on the screen depending on the type of the input 
•	
signal, such symptom is not a malfunction.
Images may not be projected in the correct position, depending on the type of the input signal. In such a case,\
 
•	
press the AUTO POSITION button. (See page 24.)
The projector automatically selects the appropriate signal format. (The selected signal format is displayed on 
•	
the INFORMATION menu.)
You cannot change the input source while the menu is being displayed.
•	
When COMPUTER is chosen as the source, images supplied from the computer may flicker. Press the 
•	 t or u 
button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
7. 
their specified sizes.
Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 
8. 
10.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the 
9. 
button again to display “ZOOM.”
Adjust with the 
10.  t or u button to get an approximate size.
When the ENTER button is pressed while “ZOOM” is displayed, the adjustment mode is switched b\
etween 
•	
FAST and STEP. When FAST is selected, the speed of zoom controlled by the t or u button becomes fast, 
and it becomes slow when STEP is selected.
C. Projecting images
Preparation:
Remove the lens cap.
•	
Viewing computer images (continued)
POWER button ON ( I ) button
COMPUTER button
LENS SHIFT button
ZOOM/FOCUS button
ZOOM/FOCUS button
LENS SHIFT button
HDMI/COMPUTER button ENTER button
p, q, t, u buttons
STATUS indicatorPOWER indicator p, q, t, u buttons ENTER button 
						

							EN-24
Viewing computer images (continued)
Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of \
the screen.
11. 
Press the 
12.  p or q button to adjust the vertical position and t or u button to adjust the horizontal position of the 
displayed image.
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
•	
Repeat steps 4 to 5 and 9 to 12, if necessary. 
To stop projecting:
Press the POWER button on the projector or the OFF (
13. ) button on the remote control.
A confirmation message is displayed.
•	
To cancel the procedure, leave the projector for a while or press the MENU button.
•	
Press the POWER button on the projector or the OFF (
14. 
) button on the remote control again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
•	
blinks green.
Wait about 2 minutes.
15. 
During this period of 2 minutes in the standby mode, the intake fan and \
exhaust fan rotate to cool the lamp.
•	
The lamp can’t be lit again for 1 minute after turning off the projector for safety purpose. It will take another 1 
•	
minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator 
goes out, and then press the POWER button.
The air outlet fans rotate faster as the temperature around the projector rises.
•	
Do not turn off the main power switch or unplug the power cord while the STATUS indicator is blinking. Turning 
•	
off the main power switch or unplugging the power cord immediately after use may cause a breakdown. 
Though the fan makes loud sounds during cooling, such symptom is not a m\
alfunction.
•	
Turn off the main power switch.
16. 
The POWER indicator will go out.
•	
If the main power switch should be turned off or the power cord should be unplugged accidentally while either 
•	
the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 
minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up 
immediately, repeat pressing the POWER button 2 or 3 times. If it should still fail to light u\
p, replace the lamp.
Cover the lens with the lens cap to protect it from dust. 
•	
For safety’s sake, unplug the power cord from the outlet.
•	
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
Display a bright image (such as a full-screen display of the Recycle Bin window).
1. 
When the screen saver has been enabled, disable it.
2. 
Press the AUTO POSITION button.
3. 
The projector automatically makes optimum positional settings for the input si\
gnal.
If the image is not projected in the correct position even after you press the AUTO POSITION button several 
•	
times, change the settings in the SIGNAL menu to put the image in the co\
rrect position. (See page 34.)
When you carry out this procedure with a dark image, the image may be displaced.
•	
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (T\
he key to be pressed depends on the type of 
the computer you use.) 
Setting of the resolution
If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure 
that their resolutions are the same (see page 45). For the method to change the output resolution of the computer, 
contact the manufacturer of the computer.  
						

							EN-25
Menu operation
Menus are not displayed when no signal is supplied to the projector.
•	
IMAGE GAMMA MODE AUTO, SPORTS, VIDEO, CINEMA
USER1 REFERENCE SPORTS, VIDEO, CINEMA
USER2 ADJUST MODEALL, RED, GREEN, BLUE
CONTRAST ±30HIGH±10(R) ±10(G) ±10(B)
BRIGHTNESS ±30MID±10(R) ±10(G) ±10(B)
COLOR TEMP.
HIGH BRIGHTNESSLOW ±10(R) ±10(G) ±10(B)
COOL REFERENCE
COOL, MEDIUM, WARMMEDIUM CONTRAST R ±60
WARM CONTRAST G ±60
USER 
CONTRAST B ±60
BRIGHTNESS R ±60
  COLOR  ±10
BRIGHTNESS G ±60
  TINT  ±10
BRIGHTNESS B ±60
  SHARPNESS  *1 ±10
ADVANCED MENU OK
 
SCREEN SIZE 16:9, CINEMA SCOPE (2.35:1)
AV MEMORY SAVEAV MEMORY1 VERTICAL LOCATION ±26AV MEMORY2 AUTO IRISAUTO1-5AV MEMORY3 OFF  TRNR  *9 0 - 15
  MNR  *9 0 - 15
  BAR  *9 ON , OFF
  CTI  *1 0 - 5
INPUT LEVEL ±5
(for analog signal input)
AUTO, ENHANCED, NORMAL
(for digital signal input) *10
INSTALLATION KEYSTONE±15
LAMP MODE STANDARD, LOW
AUTO POWER ON ON , OFF
AUTO POWER OFF OFF, 5, 10, 15, 30, 60min
SPLASH SCREEN ON, OFF
BACK COLOR BLUE, BLACK
IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT TRIGGER OUT SCREEN, ANAMORPHIC, OFF ZOOM/FOCUS LOCKON, OFF
TEST PATTERN
CROSS HATCH , WHITE , BLACK LENS SHIFT LOCK ON, OFF
LENS LOCK OK LENS SHIFT RESET OK 
FEATURE
ASPECTAUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRETCH, ANAMORPHIC1, ANAMORPHIC2 *4PASSWORD FUNCTIONDISPLAY INPUT , MENU ACCESS LOCKOK MENU POSITION1 (Upper left), 2(Lower right)UNLOCK OK MENU DIMMER
ON, OFF
  CINEMA MODE  *2 AUTO, VIDEO, FILM
  VIDEO SIGNAL  *3 AUTO, NTSC , PAL , SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
  SETUP  *1 AUTO, OFF, 3.75%, 7.5%
  SCART INPUT  *8 ON, OFF LANGUAGE
, English, Español, Deutsch, Français, Italiano, , , , PORTUGUÊS
RESET ALL OK 
SIGNAL
  HORIZ.POSITION  *6 0 - 999 *4
  VERT.POSITION  *6 0 - 999 *4
  FINE SYNC.  *5, *6 0 - 31
  TRACKING  *1, *5, *6 0 - 9999 *4  
COMPUTER INPUT  *5AUTO, RGB, YCBCR / YPBPR
OVER SCAN 100 - 90% *4
  HOLD  *5, *6 OFFBEGIN0 - 99
ON 
  END  0 - 99
USER OK  CLAMP POSITION  *5, *6
1- 255 *4
 
CLAMP WIDTH  *5, *6 1- 63 *4
INFORMATION LAMP TIME(LOW)
VERT.SYNCAUTO, OFF
INPUT   LPF  *5, *6, *7 ON, OFF
RESOLUTION SHUTTER(U)0 - 32
VERTICAL FREQUENCYSHUTTER(L)0 - 32HORIZONTAL FREQUENCYSHUTTER(LS) 0 - 95
  SYNC. TYPE  *5, *6
SHUTTER(RS)0 - 95
* 1:  Not available with certain signals.
* 2:  Available only when the input signal is TV50, TV60, 480i, 576i or 1080i.
* 3:  Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
* 4:  Setting range differs depending on the input signals.
* 5:  Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
* 6:  Not available when the input signal is from the HDMI IN terminal.
* 7:  Available only when the input signal is 480i, 480p, 576i, or 576p.
* 8:  Available only when the input signal is from the COMPUTER IN/COMPONENT VIDEO IN terminal.
* 9:  Available only when the input signal is 480i, 480p, 576i, 576p, TV60 or T\
V50. 
*
 10:  Available only when RGB output is selected on the output device side. 
						

							EN-26
How to set the menus:
The following describes how to set AUTO POWER 
OFF time as an example.Press the MENU button.
1. 
CONTRAST
IMAGE
0
BRIGHTNESS 0
0
COLOR
OK
MIDIUM
0
TINT
0SHARPNESS
COLOR TEMP.
ADVANCED MENU
opt.
AUTOGAMMA MODE
AV MEMORY 1
AV MENU SAV EAV MEMORY 1
Press the 
2.  t or u button to select a menu to use.
IMAGE
REVERSE
OFF
AUTO POWER 
ON
OFFAUTO POWER 
OFF
SCREEN SIZE
ON
INS T ALL A TION 
ON
BACK COLOR
OFF
TEST PATTERNCROSS HATCHBLUE
SPLASH
SCREEN WXGA (FULL)
VERTICAL LOCATION0
opt.
STANDARD
LAMP MODE
A V MEMO R Y 1 
Press the ENTER button (or 
3.  q button).
IMAGE
REVERSE
OFF OFF
BACK COLOR
OFF
opt.
STANDARD
LAMP MODE
AV MEMORY 1
LENS LOCK
OK
AUTO POWER
ON
AUTO POWER
OFF
INSTALLATION
TRIGGER OUT
OFF
ONON
BLUE
SPLASH
SCREEN
TEST PATTERN
CROSS HATCH
KEYSTONE 0
1. IMAGE menu
ITEMSETTING FUNCTION
CONTRAST
IMAGE
0
BRIGHTNESS 0
0
COLOR
OK
MEDIUM
0
TINT
0SHARPNESS
COLOR TEMP.
ADVANCED MENU
opt.
AUTOGAMMA MODE
AV MEMORY 1
AV MEMORY
SAVEAV MEMORY1
GAMMA MODE AUTO The proper gamma mode is  automatically selected depending on 
the input signal. Default is AUTO. 
SPORTS This is a bright mode suitable for  watching sports images.
VIDEO This is a standard mode suitable for  watching video images, etc.
CINEMA This is a mode for watching movies in  dim lighting as in a theater.
USER1 
 / 
USER2 Select to adjust the gamma curve. (See 
page 33.)
CONTRAST ±30 Use to adjust the contrast of the 
projected image. (See page 31.)
BRIGHTNESS ±30 Use to adjust the brightness of the projected image. (See page 31.)
COLOR TEMP. 5 options Use to adjust the color temperature. (See page 32.)
COLOR ±10 Use to adjust the color thickness of the projected image. (See page 31.)
TINT ±10 Use to adjust the color tint of the projected image. (See page 31.)
SHARPNESS ±10 Use to adjust the sharpness of the projected image. (See page 31.)
ADVANCED MENU SCREEN SIZE 2 options Select according to the screen size.
VERTICAL LOCATION±26 Use to adjust the position (height) of the projected image.
AUTO IRIS AUTO / OFF Select the operation mode of the auto iris. (See page 32.)
TRNR 0 - 15 Use to reduce random noise. (See page 33.)
MNR 0 - 15 Use to reduce mosquito noise. (See page 33.)
BAR ON / OFF Use to reduce block noise. (See page 33.)
CTI 0 - 5 Use to correct smeared color boundaries.
INPUT LEVEL ±5 For analog signal input: The input level of video signal differs among devices to be 
connected. High input level causes solid white in displayed image and lo\
w input 
level causes displayed image to get dark. Use this menu to adjust the in\
put level of 
analog video signal.
AUTO /
ENHANCED /  NORMAL
For digital signal input:AUTO:  The proper setting is automatically selected.
ENHANCED:  Select when solid black occurs.
NORMAL:  Select when grayish black occurs.
(See page 16.)
AV MEMORY SAVE3 options Select the AV MEMORY to which you save the current setting. (See page 30.)
By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. (See 
•	
page 30.)
INPUT LEVEL is unavailable when the digital signal is supplied from the YC
•	
BCR/YPBPR terminal of the connected device.
Available settings in the menus
Set the following items on their relevant menus. Press the 
4.  p or q button to select an item to 
adjust.
IMAGE
REVERSE
OFF
AUTO POWER 
ON
OFFAUTO POWER 
OFF
SCREEN SIZE 
ON
INS T ALL A TION 
ON
BACK COLOR
OFF
TEST PATTERNCROSS HATCHBLUE
SVGA60
SPLASH
SCREEN WXGA (FULL) 
VERTICAL LOCATION0
opt.
STANDARD
LAMP MODE
A V MEMO R Y 1 
Set the selected item by pressing the 
5.  t or u 
button.
IMAGE
REVERSE
30 min
AUTO POWER 
ON
OFFAUTO POWER 
OFF
SCREEN SIZE 
ON
INS T ALL A TION 
ON
BACK COLOR
OFF
TEST PATTERNCROSS HATCHBLUE
SVGA60
SPLASH
SCREEN WXGA (FULL) 
VERTICAL LOCATION0
opt.
STANDARD
LAMP MODE
A V MEMO R Y 1 
To cancel the menu:
Press the MENU button several times.
6. 
Important:
When the MENU button doesn’t function, unplug 
•	
the power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again.
After selecting the items marked with 
•	
, press the 
ENTER button.
Menu operation (continued)
1. IMAGE menu 
						

							EN-27
2. INSTALLATION menu
ITEMSETTING FUNCTION
KEYSTONE ±15 Use to correct vertical keystone distortion.
LAMP MODE STANDARD Select this option when you want to view images in a well-lit room. LOW Select to moderate the intensity of the lamp. The fan operating sound is\
 
reduced and the lamp lifetime becomes longer.
AUTO POWER ONON / OFF When ON is chosen, the lamp is automatically lit when the power cord is  plugged in the wall outlet. Choose ON when using the projector mounted on 
the ceiling.The projector is in the stand-by mode when the lamp is off. Use the remote 
•	
control to turn on the lamp.
AUTO POWER OFFOFF / 5 - 60min Use to set the time elapsed before the projector enters the stand-by mode  when there is no signal input from the source.
SPLASH SCREEN ON / OFF Choose ON to display the splash screen when the power is turned on.
BACK COLOR BLUE / BLACK Use to change the color of the screen that appears when no signal is supplied.
IMAGE REVERSEOFF Select when viewing images from the front with the projector installed on the 
floor.
MIRROR Select when viewing images projected from the behind of the screen with the 
projector installed on the floor.
INVERT Select when viewing images projected from the behind of the screen with the 
projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed on the 
ceiling.
TRIGGER OUT SCREEN The trigger output signal (12 V) is output from the TRIGGER terminal when the 
lamp illuminates.
ANAMORPHIC The trigger output signal (12 V) is output from the TRIGGER terminal when the 
aspect ratio is set to ANAMORPHIC 1 or ANAMORPHIC 2.
OFF The trigger output signal (12V) isn’t output. 
TEST PATTERN CROSS HATCH 
Select to show the test cross hatch pattern.
WHITE 
Select to show the maximum brightness image.
BLACK 
Select to show the minimum brightness image.
LENS LOCK
ZOOM/FOCUS LOCKUse to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCKUse to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESETUse to reset the position of the lens to the factory setting.
When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute 
•	
after turn-on.
When the lamp mode is switched, the projected image may flicker. This is not a product malfunction.
•	
Do not change the setting of LAMP MODE frequently.
•	
To cancel the test pattern, press any button. 
•	
IMAGE
REVERSE
OFF OFF
BACK COLOR
OFF
opt.
STANDARD
LAMP MODE
A V MEMO R Y 1 
LENS LOCK
OK
AUTO POWER
ON
AUTO POWER
OFF
INSTALLATION
TRIGGER OUT
OFF
ONON
BLUE
SPLASH
SCREEN
TEST PATTERN
CROSS HATCH
KEYSTONE 0
2. INSTALLATION menu
Menu operation (continued) 
						

							EN-28
3. FEATURE menu
FE A TURE 
AUTO
AUTO AUTO
opt.
MENU POSITION
CINEMA MODE VIDEO SIGNAL?
ASPECT
RESET ALL
English
LANGUAGEAË
OFF
AUTO
OK
DISPLAY
INPUT
PASSWORD
FUNCTION
1.
MENU DIMMER
A V MEMO R Y 1 
SETUP
SCART INPUT
OFF
Menu operation (continued)
3. FEATURE menu
ITEM
SETTING FUNCTION
ASPECT AUTO Select to change the aspect ratio automatically depending on the input s\
ignal.
4:3 Select to project images with an aspect ratio of 4:3.
16:9 Select to project images with an aspect ratio of 16:9. (Linearly stretched.)
ZOOM1 Select to enlarge and project images of CinemaScope size.
ZOOM2 Select to enlarge and project images of Vista size.
STRETCH Select to enlarge to 16:9 and project of the images with an aspect ratio of 4:3.  (Non-linearly stretched.)
ANAMORPHIC1
This mode is suitable for viewing 2.35:1-size images using the anamorphi\
c lens. 
Use the p or q key to adjust the vertical display position. 
This mode doesn’t support input signals from personal computers.
ANAMORPHIC2 This mode is suitable for viewing 16:9- or 4:3-size images or images inp\
ut from  personal computers using the anamorphic lens. 
PASSWORD FUNCTIONUse to enable or cancel the password lock. See page 35 for details.
MENU POSITION2 options Use to change the position of the menu.
MENU DIMMERON / OFF Use to reduce the brightness of the menu.
CINEMA MODE AUTO The film mode will be automatically activated when a film source signal is input. Select AUTO for normal use. 
When flicker occurs on the screen or jaggies on slanting lines are remarkable, 
select FILM when a film source signal is input or select VIDEO for other signals. 
VIDEO The film mode will not be activated.
FILM Fixed to the film mode.
VIDEO SIGNAL 8 options When AUTO is selected, the appropriate video format is automatically selected  depending on the input signal. If the image isn’t displayed correctly, select the 
desired video format manually.
SETUP AUTO
Select AUTO for normal use. When LANGUAGE is not set to 
 and 480i, 
480p or TV60 signal is input, the SETUP changes to 7.5% automatically.
OFF Select to make black lighter.
3.75% / 7.5% Select to make black intense. When 7.5% is chosen, the brightness is decreased by the set-up cancel 
•	
function for the U.S. Choose OFF when the image is dark.
SCART INPUT ON / OFF Choose ON when connecting the projector with a device equipped with the  SCART terminal that can output RGB signal. SCART terminal is used mainly 
in Europe. Choose OFF normally. (Available only for the input signal from the 
COMPUTER IN/COMPONENT VIDEO IN terminal.)
LANGUAGE 10 languages Use to select the language used in the menus.
RESET ALL OK 
Use to reset the settings of the menu (excluding PASSWORD FUNCTION and 
LANGUAGE) to the factory setting values.
When SCREEN SIZE of ADVANCED MENU is set to CINEMA SCOPE (2.35:1) in the IMAGE menu, STRETCH \
•	
cannot be selected for ASPECT.
When SCART INPUT is set to ON, normal computer signals aren’t projected.
•	
Use a SCART-BNC (or SCART-Mini D-SUB 15-pin) cable (option) when connecting this projector with an AV device 
•	
equipped with the SCART terminal.
Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
•	
It may take a little while to carry out RESET ALL in the FEATURE menu.
•	 
						

							EN-29
4. SIGNAL menu 5. USER menu
R G B R G B
SIGNAL 
HORIZ. POSITION0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUT AUTO
FINE SYNC.
0
USER
opt.
OK
ONHOLD
100%
OVER SCAN
A V MEMO R Y 1 CLAMP 
POSITION
USER 
1
CLAMP WIDTH 1
LPF OFF
SHUTTER(U) 0
SHUTTER(L) 0
VERT. SYNC
AUTO
?
SHUTTER(LS) 0
SHUTTER(RS) 0
Menu operation (continued)
4. SIGNAL menu
ITEMSETTING FUNCTION
HORIZ. POSITION0 - 999 Use to adjust the horizontal position of the projected image.
VERT. POSITION0 - 999 Use to adjust the vertical position of the projected image.
FINE SYNC. 0 - 31 Use to eliminate flickering or blur, if it appears, while viewing the projected 
image. 
TRACKING 0 - 9999 Use to eliminate vertical wide stripes, if it appears, while viewing the\
 projected 
image.
COMPUTER INPUTAUTO The proper setting is automatically selected.RGB Select this option when connecting the projector to high definition video 
equipment having R, G, and B output terminals.
YC
BCR / YPBPRSelect this option when connecting the projector to a DVD player or other 
device having Y, C
B, and CR (or Y, PB, and PR) component video output 
terminals.
OVER SCAN 100 - 90% Use to adjust the display area of the projected image when playing LD and 
DVD discs.
HOLD OFF / ON 
Use to adjust the image when flagging occurs near the top of the screen.
Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
•	
When you change the horizontal or vertical position to a large extent, noise may appear.
•	
The adjustable range of the vertical position varies depending on the ty\
pe of the input signal. Though the image 
•	
may stay in the same position even when the setting value is changed, su\
ch symptom is not a malfunction.
If you increase the OVER SCAN setting when viewing video signals, noise may appear \
on the screen. In this case, 
•	
decrease the OVER SCAN setting.
5. USER menu
ITEM SETTING FUNCTION
CLAMP POSITION1 - 255 Use to correct solid white or solid black in the projected image.
CLAMP WIDTH 1 - 63 Use to correct solid black in the projected image.
VERT. SYNC AUTO / OFF Use to adjust the image when its motion doesn’t run smoothly. Select AUTO for 
normal use.
LPF ON / OFF Use to select whether or not to enable the LPF.
SHUTTER(U) 0 - 32 Use to display the black bar on the top part of the image.
SHUTTER(L) 0 - 32 Use to display the black bar on the bottom part of the image.
SHUTTER(LS) 0 - 95 Use to display the black bar on the left half of the image.
SHUTTER(RS) 0 - 95 Use to display the black bar on the right half of the image. 
						

							EN-30
6. INFORMATION menu
Menu operation (continued)
INFORMATION 
opt.
LAMP TIME(LOW)
INPUT
RESOLUTION
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE5wire
60.02 KHz 75.04 Hz
1024X768
COMPUTER 0 HR  G 
H  V  B 
6. INFORMATION menu
ITEM
DESCRIPTION
LAMP TIME(LOW) This item shows a lamp operating time (hour) calculated based on that \
LAMP MODE 
is LOW.
When the LAMP MODE is STANDARD, this item shows a longer lamp operating 
•	
time than the actual time. (See page 36 for the interval of lamp replacement. )
When the lamp operating time is 0 to 10 hours, “0H” is displayed. \
The lamp 
•	
operating time exceeding 10 hours is indicated by the actual hours.
When the lamp operating time reaches 3000 hours, the bar turns to yellow. When 
•	
it reaches 3800 hours, the bar turns to red.
INPUT Indicates the name of the terminal to which the currently projected video signal is 
being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FREQUENCY Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
AV memory
You can store up to 3 patterns of the image quality setting for each input source.
To store the settings
Set the items of the IMAGE menu.
1. 
Setting the items by using the picture quality adjusting buttons on the remote control is also available.
•	
Press the 
2.  p or q button to select AV MEMORY SAVE.
Press the 
3.  t or u button to select AV MEMORY (1, 2 or 3) to store the settings. 
Press the ENTER button.
4. 
To enable the stored image quality settings
Press the AV MEMORY button to call up the stored setting.
1. 
When you make change to the stored setting you call up, the changed setting remains effective but is not saved to 
•	
the AV MEMORY unless AV MEMORY SAVE is executed.
When the input source is changed, the AV memory setting selected just before is automatically selected.
•	
When RESET ALL in the FEATURE menu is selected, all the settings of the AV memory are cleared.
•