Mitsubishi Hc5000bl Projector User Manual

							EN-21
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
2  1 
2 
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
1To DVI
A. Connecting the projector to a computer
Preparation:
Make sure that the power of the projector and that of the computer are turned off.
When connecting the projector to a desktop computer, disconnect the RGB cables that are connected to the 
monitor.  •
•
For analog connection:
Connect one end of the supplied RGB cable to the 
COMPUTER IN/COMPONENT VIDEO IN terminal of the 
projector.
Connect the other end of the RGB cable to the monitor 
port of the computer.
Additional devices, such as a conversion connector and an 
analog RGB output adapter, are required depending on the 
type of the computer to be connected.
When viewing images supplied from an analog-connected 
computer, press the COMPUTER button on the remote 
control. 1.
2.
•
•
Turn on the power of the projector before that of the computer.
Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending 
on the type of the computer to be connected.
Use of a long cable may decrease the quality of projected images.
Also read the instruction manual of the equipment to be connected.
Images may not be projected correctly, depending on the type of the computer connected.
Contact your dealer for details of connection.
About DDC
The COMPUTER IN/COMPONENT VIDEO IN terminal of this projector complies with the DDC1/2B standard and 
the DVI-D(HDCP) IN and HDMI IN terminals comply with the DDC2B standard. When a computer supporting this 
standard is connected to this terminal, the computer will automatically load the information from this projector and 
prepare for output of appropriate images.
After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the 
wall outlet fi rst, and then boot up the computer.
B. Plugging the power cord
Plug the power cord in the same way as described in “Viewing video images.” (See page 16.) •
•
•
•
•
•
•
To monitor port COMPUTER IN/
COMPONENT VIDEO IN
RGB cable
DVI cable (option) DVI-D(HDCP) IN
Viewing computer images
For digital connection:
Connect one end of a commercially available DVI cable to 
the DVI-D(HDCP) IN terminal of the projector.
Connect the other end of the DVI cable to the DVI terminal 
of the computer.
Additional devices, such as a conversion connector and an 
analog RGB output adapter, are required depending on the 
type of the computer to be connected.
When viewing images supplied from a digital-connected 
computer, press the DVI button on the remote control.
The signal input to the DVI-D(HDCP) IN terminal is not 
output from the COMPUTER OUT terminal. 1.
2.
•
•
• 
						

							EN-22
Confi rm the POWER indicator lights-up red.
If the projector was turned off before the lamp had cooled down suffi ciently, the fan may start rotating and the 
POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the 
fan stops rotating, press the power button to turn back on the POWER indicator.
Press the POWER button on the projector or ON ( I ) button on the remote control.
It may take about one minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the 
lens cap.
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a 
product malfunction.
The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP 
MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
The projector starts warming up when the POWER button is pressed. During the warm-up process, images 
may appear dark and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See page 41.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
Adjust with the W or X button to get a fi ne picture.
Select an input source.
Press the HDMI/DVI button on the projector or the COMPUTER , HDMI or DVI button on the remote control 
that is corresponding to the terminal in use.
The input source is switched between COMPUTER, HDMI and DVI every time you press the HDMI/DVI button 
on the projector.
Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction.
Images may not be projected in the correct position, depending on the type of the input signal. In such a case, 
press the AUTO POSITION button. (See page 23.)
The projector automatically selects the appropriate signal format. (The selected signal format is displayed on 
the INFORMATION menu.)
You cannot change the input source while the menu is being displayed.
When COMPUTER is chosen as the source, images supplied from the computer may fl icker. Press the W or X 
button on the remote control to reduce fl icker, if it occurs.
Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes.
Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 
10.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the 
button again to display “ZOOM.”
Adjust with the W or X button to get an approximate size.
Press the LENS SHIFT button. “LENS SHIFT” will appear on the display.
Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the 
displayed image.
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
Repeat steps 3 to 4 and 8 to 11, if necessary.  1.
•
2.
•
•
•
•
•
•
•
3.
4.
5.
•
•
•
•
•
•
•
6.
7.
8.
9.
10.
11.
•
C. Projecting images
Preparation:
Remove the lens cap.
Turn on the power of the connected computer.  •
•
COMPUTER button
POWER buttonON ( I ) button
Viewing computer images (continued)
DVI button
LENS SHIFT button ZOOM/FOCUS buttonZOOM/FOCUS 
button LENS SHIFT button 
						

							EN-23
To stop projecting:
Press the POWER button on the projector or the OFF () button on the remote control.
A confi rmation message is displayed.
To cancel the procedure, leave the projector for a while or press the MENU button.
Press the POWER button on the projector or the OFF (
) button on the remote control again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green.
Wait about 2 minutes.
During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
The lamp can’t be lit again for 1 minute after turning off the projector for safety purpose. It will take another 1 
minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator 
goes out, and then press the POWER button.
The air outlet fans rotate faster as the temperature around the projector rises.
Do not unplug the power cord while the STATUS indicator is blinking. Unplugging the power cord immediately 
after use may cause a lamp breakdown.
Though the fan makes loud sounds during cooling, such symptom is not a malfunction.
Unplug the power cord from the outlet.
The POWER indicator will go out.
If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are 
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the 
lamp again, press the POWER button. If the lamp doesn’t light up immediately, repeat pressing the POWER 
button two or three times. If it should still fail to light up, replace the lamp.
Cover the lens with the lens cap to protect it from dust.  12.
•
•
13.
•
14.
•
•
•
•
•
15.
•
•
•
AUTO POSITION button
Viewing computer images (continued)
POWER buttonOFF (
) button
AUTO POSITION button
When connecting to a notebook computer:
When the projector is connected to a notebook computer, images may not be projected in some cases. In such 
cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type 
of the computer. See the instruction manual of your computer.
Example of the setting procedure for external output
Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of 
the computer you use.) 
AUTO POSITION button
When the image supplied from the computer is displaced, carry out the following procedure.
Display a bright image (such as a full-screen display of the Recycle Bin window).
When the screen saver has been enabled, disable it.
Press the AUTO POSITION button.
The projector automatically makes optimum positional settings for the input signal.
If the image is not projected in the correct position even after you press the AUTO POSITION button several 
times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 33.)
When you carry out this procedure with a dark image, the image may be displaced. 1.
2.
3.
•
• 
						

							EN-24
Menu operation
Menus are not displayed when no signal is supplied to the projector.
IMAGE GAMMA MODE AUTO, SPORTS, VIDEO, CINEMA
USER1 
REFERENCE SPORTS, VIDEO, CINEMA
USER2 
ADJUST MODEALL, RED, GREEN, BLUE
CONTRAST ±30 HIGH ±10(R) ±10(G) ±10(B)
BRIGHTNESS ±30 MID ±10(R) ±10(G) ±10(B)
COLOR TEMP.
HIGH BRIGHTNESSLOW ±10(R) ±10(G) ±10(B)
COOL
CONTRAST R ±60
MEDIUM
CONTRAST G ±60
WARM
CONTRAST B ±60
USER 
BRIGHTNESS R ±60
 COLOR  ±10
BRIGHTNESS G ±60
 TINT  ±10
BRIGHTNESS B ±60
 SHARPNESS *1 ±10
ADVANCED MENU
OK 
SCREEN SIZE 16:9, CINEMA SCOPE(2.35:1)
AV MEMORY SAVE
AV MEMORY1 VERTICAL LOCATION ±26
AV MEMORY2 AUTO IRIS
AUTO IRIS 1, AUTO IRIS 2, 
AUTO IRIS 3, OPEN
AV MEMORY3 
  TRNR  *9 0 - 15
  MNR  *9 0 - 15
  BAR  *9 ON , OFF
  CTI  *1 0 - 5
INPUT LEVEL ±5
(for analog signal input)INSTALLATION LAMP MODE STANDARD, LOW
AUTO POWER ON ON , OFF ENHANCED/NORMAL
(for digital signal input)AUTO POWER OFF OFF, 5, 10, 15, 30, 60min
SPLASH SCREEN ON , OFF
BACK COLOR BLUE, BLACK
IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
TRIGGER OUT ON , OFF ZOOM/FOCUS LOCK ON, OFF
TEST PATTERNCROSS HATCH 
LENS SHIFT LOCK ON, OFF
LENS LOCKOK 
LENS SHIFT RESETOK 
FEATURE ASPECT AUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRETCH *4
PASSWORD FUNCTIONDISPLAY INPUT , MENU ACCESS LOCKOK 
MENU POSITION1 (Upper left), 2(Lower right)UNLOCKOK 
MENU DIMMER ON, OFF
  CINEMA MODE  *2 AUTO , OFF
  VIDEO SIGNAL  *3 AUTO , NTSC , PAL , SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
  SETUP  *1 AUTO, OFF, 3.75%, 7.5%
  SCART INPUT  *8 ON, OFF
LANGUAGE
, English, Español, Deutsch, Français, Italiano, , , , PORTUGUÊS
RESET ALLOK 
SIGNAL  HORIZ.POSITION *6 0 - 999 *4
  VERT.POSITION *6 0 - 999 *4
 FINE SYNC. *5, *6 0 - 31
  TRACKING  *1, *5, *6 0 - 999 *4
 
COMPUTER INPUT *5AUTO, RGB, YCBCR / YPBPR
OVER SCAN 100 - 90% *4
  HOLD  *5, *6 OFF BEGIN 0 - 99
ON 
  END  *5 0 - 99
USEROK 
 CLAMP POSITION *6 1- 255 *4
 
CLAMP WIDTH  *5, *6 1- 63 *4
INFORMATION LAMP TIME(LOW)
VERT.SYNC AUTO, OFF
INPUT
  LPF  *6, *7 ON, OFF
RESOLUTION
SHUTTER(U) 0 - 32
VERTICAL FREQUENCYSHUTTER(L) 0 - 32HORIZONTAL FREQUENCYSHUTTER(LS) 0 - 95
  SYNC. TYPE  *5, *6
SHUTTER(RS) 0 - 95
* 1:  Not available with certain signals.
* 2:  Available only when the input signal is TV50, TV60, 480i, 576i or 1080i.
* 3:  Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
* 4:  Setting range differs depending on the input signals.
* 5:  Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
* 6:  Not available when the input signal is from the HDMI IN or DVI-D(HDCP) IN terminal.
* 7:  Available only when the input signal is 480i, 480p, 576i, or 576p.
* 8:  Available only when the input signal is from the COMPUTER IN/COMPONENT VIDEO IN terminal.
* 9:  Available only when the input signal is 480i, 480p, 576i, 576p, TV60 or TV50. 
• 
						

							EN-25
How to set the menus:
The following describes how to set AUTO POWER 
OFF time as an example.
Press the MENU button.
When no signal is applied, the menu would not 
appear.
IMAGE
opt.
AV MEMORY 1
Press the W or X button to select a menu to use.
INS T ALL A TION 
opt.
A V MEMO R Y 1 
Press the ENTER button (or T button).
opt.
STANDARD LAMP MODE
AV MEMORY 1
INSTALLATION
1.
•
2.
3.
1. IMAGE menu
ITEM SETTING FUNCTION
CONTRAST
IMAGE
0
BRIGHTNESS 0
0
COLOR
OK MEDIUM
0
TINT
0SHARPNESS
COLOR TEMP.
ADVANCED MENU
opt.
AUTOGAMMA MODE
AV MEMORY 1
AV MEMORY
SAVEAV MEMORY1
GAMMA MODE AUTO The proper gamma mode is 
automatically selected depending on 
the input signal. Default is AUTO. 
SPORTS This is a bright mode suitable for 
watching sports images.
VIDEO This is a standard mode suitable for 
watching video images, etc.
CINEMA This is a mode for watching movies in 
dim lighting as in a theater.
USER1 
 / 
USER2 Select to adjust the gamma curve. 
(See page 32.)
CONTRAST ±30 Use to adjust the contrast of the 
projected image. (See page 30.)
BRIGHTNESS ±30 Use to adjust the brightness of the projected image. (See page 30.)
COLOR TEMP. 5 options Use to adjust the color temperature. (See page 31.)
COLOR ±10 Use to adjust the color thickness of the projected image. (See page 30.)
TINT ±10 Use to adjust the color tint of the projected image. (See page 30.)
SHARPNESS ±10 Use to adjust the sharpness of the projected image. (See page 30.)
ADVANCED MENU
SCREEN SIZE 2 options Select according to the screen size.
VERTICAL LOCATION±26 Use to adjust the position (height) of the projected image.
AUTO IRIS 4 options Select an iris mode depending on the projected image. (See page 31.)
TRNR 0 - 15 Use to reduce random noise. (See page 32.)
MNR 0 - 15 Use to reduce mosquito noise. (See page 32.)
BAR ON/OFF Use to reduce block noise. (See page 32.)
CTI 0 - 5 Use to correct smeared color boundaries.
INPUT LEVEL ±5
ENHANCED / 
NORMAL
For analog signal input: The input level of video signal differs among devices to 
be connected. High input level causes solid white in displayed image and low 
input level causes displayed image to get dark. Use this menu to adjust the input 
level of analog video signal.
For digital signal input: When a digital signal is input, ENHANCED and NORMAL 
are switchable. (See page 16.)
AV MEMORY SAVE
3 options Select the AV MEMORY to which you save the current setting. (See page 29.)
By using the AV memory function, you can save up to 3 setting patterns of IMAGE menu for each input terminal. 
(See page 29.)
INPUT LEVEL is unavailable when the digital signal is supplied from the YC
BCR/YPBPR terminal of the connected 
device. •
•
Available settings in the menus
Set the following items on their relevant menus.Press the S or T button to select an item to 
adjust.
OFF AUTO POWER 
ONOFFAUTO POWER 
OFF
Set the selected item by pressing the W or X 
button.
30 min AUTO POWER 
ONOFFAUTO POWER 
OFF
To cancel the menu:
Press the MENU button several times.
Important:
When the MENU button doesn’t function, unplug 
the power cord from the wall outlet. Wait about 10 
minutes, plug the power cord in, and try again.
After selecting the items marked with 
, press the 
ENTER button. 4.
5.
6.
•
•
Menu operation (continued)
1. IMAGE menu 
						

							EN-26
2. INSTALLATION menu
ITEM SETTING FUNCTION
LAMP MODE STANDARD Select this option when you want to view images in a well-lit room.
LOW Select to moderate the intensity of the lamp. The fan operating sound is 
reduced and the lamp lifetime becomes longer.
AUTO POWER ONON / OFF When ON is chosen, the lamp is automatically lit when the power cord is 
plugged in the wall outlet. Choose ON when using the projector mounted on 
the ceiling.
The projector is in the stand-by mode when the lamp is off. Use the remote 
control to turn on the lamp. •
AUTO POWER OFFOFF / 5 - 60min Use to set the time elapsed before the projector enters the stand-by mode 
when there is no signal input from the source.
SPLASH SCREEN ON / OFF Choose ON to display the splash screen when the power is turned on.
BACK COLOR BLUE / BLACK Use to change the color of the screen that appears when no signal is supplied.
IMAGE REVERSEOFF Select when viewing images from the front with the projector installed on the 
fl oor.
MIRROR Select when viewing images projected from the behind of the screen with the 
projector installed on the fl oor.
INVERT Select when viewing images projected from the behind of the screen with the 
projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed on the 
ceiling.
TRIGGER OUT ON / OFF Choose ON to output the trigger output signal (12 V) from the TRIGGER 
terminal when the lamp illuminates.
TEST PATTERNCROSS HATCH 
Select to show the test cross hatch pattern.
LENS LOCK
ZOOM/FOCUS LOCKUse to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCKUse to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESETUse to reset the position of the lens to the factory setting.
When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about one minute 
after turn-on.
When the lamp mode is switched, the projected image may fl icker. This is not a product malfunction.
Do not change the setting of LAMP MODE frequently.
To cancel the test pattern, press any button.  •
•
•
•
IMAGE
REVERSE
OFF OFF
BACK COLOR
OFF
opt.
STANDARD LAMP MODE
A V MEMO R Y 1 
LENS LOCK
OK
AUTO POWER
ON
AUTO POWER
OFF
INSTALLATION
TRIGGER OUT
OFF
ONON
BLUE SPLASH
SCREEN
TEST PATTERN
CROSS HATCH
2. INSTALLATION menu
Menu operation (continued) 
						

							EN-27
3. FEATURE menu
FE A TURE 
AUTO
AUTO AUTO
opt.
MENU POSITION
CINEMA MODE
VIDEO SIGNAL?
ASPECT
RESET ALL
English
LANGUAGEAË
OFF
AUTO
OK
DISPLAY
INPUT PASSWORD
FUNCTION
1.
MENU DIMMER
A V MEMO R Y 1 
SETUP
SCART INPUT
OFF
Menu operation (continued)
3. FEATURE menu
ITEM SETTING FUNCTION
ASPECT AUTO Select to change the aspect ratio automatically depending on the input signal.
4:3 Select to project images with an aspect ratio of 4:3.
16:9 Select to project images with an aspect ratio of 16:9. (Linearly stretched.)
ZOOM1 Select to enlarge and project images of CinemaScope size.
ZOOM2 Select to enlarge and project images of Vista size.
STRETCH Select to enlarge to 16:9 and project of the images with an aspect ratio of 4:3. 
(Non-linearly stretched.)
PASSWORD FUNCTIONUse to enable or cancel the password lock. See page 34 for details.
MENU POSITION2 options Use to change the position of the menu.
MENU DIMMERON / OFF Use to reduce the brightness of the menu.
CINEMA MODE AUTO The fi lm mode will be automatically activated when a fi lm source signal is input. 
OFF The fi lm mode will not be activated.
VIDEO SIGNAL 8 options When AUTO is selected, the appropriate video format is automatically selected 
depending on the input signal. If the image isn’t displayed correctly, select the 
desired video format manually.
SETUP AUTOSelect AUTO for normal use. When LANGUAGE is not set to 
 and 480i, 
480p or TV60 signal is input, the SETUP changes to 7.5% automatically.
OFF Select to make black lighter.
3.75% / 7.5% Select to make black intense.
When 7.5% is chosen, the brightness is decreased by the set-up cancel 
function for the U.S. Choose OFF when the image is dark. •
SCART INPUT ON / OFF Choose ON when connecting the projector with a device equipped with the 
SCART terminal that can output RGB signal. SCART terminal is used mainly 
in Europe. Choose OFF normally. (Available only for the input signal from the 
COMPUTER IN/COMPONENT VIDEO IN terminal.)
LANGUAGE 10 languages Use to select the language used in the menus.
RESET ALLOK 
Use to reset the settings of the menu (excluding PASSWORD FUNCTION and 
LANGUAGE) to the factory setting values.
When SCART INPUT is set to ON, normal computer signals aren’t projected.
Use a SCART-BNC (or SCART-Mini D-SUB 15-pin) cable (option) when connecting this projector with an AV device 
equipped with the SCART terminal.
Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
It may take a little while to carry out RESET ALL in the FEATURE menu. •
•
•
• 
						

							EN-28
4. SIGNAL menu  5. USER menu
R G B R G B
SIGNAL 
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER 
INPUTAUTO
FINE SYNC. 0
USER
opt.
OK
ONHOLD
100%
OVER SCAN
A V MEMO R Y 1 CLAMP 
POSITION
USER 
1
CLAMP WIDTH 1
LPF OFF
SHUTTER(U) 0
SHUTTER(L) 0 VERT. SYNC AUTO
?
SHUTTER(LS) 0
SHUTTER(RS) 0
Menu operation (continued)
4. SIGNAL menu
ITEM SETTING FUNCTION
HORIZ. POSITION0 - 999 Use to adjust the horizontal position of the projected image.
VERT. POSITION0 - 999 Use to adjust the vertical position of the projected image.
FINE SYNC. 0 - 31 Use to eliminate fl ickering or blur, if it appears, while viewing the projected 
image. 
TRACKING 0 - 9999 Use to eliminate vertical wide stripes, if it appears, while viewing the projected 
image.
COMPUTER INPUTAUTO The proper setting is automatically selected.
RGB Select this option when connecting the projector to high defi nition video 
equipment having R, G, and B output terminals.
YC
BCR / YPBPRSelect this option when connecting the projector to a DVD player or other 
device having Y, C
B, and CR (or Y, PB, and PR) component video output 
terminals.
OVER SCAN 100 - 90% Use to adjust the display area of the projected image when playing LD and 
DVD discs.
HOLDOFF / ON 
Use to adjust the image when fl agging occurs near the top of the screen.
Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
When you change the horizontal or vertical position to a large extent, noise may appear.
The adjustable range of the vertical position varies depending on the type of the input signal. Though the image 
may stay in the same position even when the setting value is changed, such symptom is not a malfunction.
If you increase the OVER SCAN setting when viewing video signals, noise may appear on the screen. In this case, 
decrease the OVER SCAN setting.
5. USER menu
ITEM SETTING FUNCTION
CLAMP POSITION1 - 255 Use to correct solid white or solid black in the projected image.
CLAMP WIDTH 1 - 63 Use to correct solid black in the projected image.
VERT.SYNC AUTO / OFF Use to adjust the image when its motion doesn’t run smoothly. Select AUTO for 
normal use.
LPF ON / OFF Use to select whether or not to enable the LPF.
SHUTTER(U) 0 - 32 Use to display the black bar on the top part of the image.
SHUTTER(L) 0 - 32 Use to display the black bar on the bottom part of the image.
SHUTTER(LS) 0 - 95 Use to display the black bar on the left half of the image.
SHUTTER(RS) 0 - 95 Use to display the black bar on the right half of the image. •
•
•
• 
						

							EN-29
6. INFORMATION menu
Menu operation (continued)
INFORMATION 
opt.
LAMP TIME(LOW)
INPUT
RESOLUTION
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire60.02 KHz75.04 Hz 1024X768 COMPUTER0 HR G 
H V B 
6. INFORMATION menu
ITEM DESCRIPTION
LAMP TIME(LOW) ............... This item shows a lamp operating time (hour) calculated based on that LAMP MODE 
is LOW.
When the LAMP MODE is STANDARD, this item shows a longer lamp operating 
time than the actual time. (See page 35 for the interval of lamp replacement. )
When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp 
operating time exceeding 10 hours is indicated by the actual hours.
When the lamp operating time reaches 3750 hours, the bar turns to yellow. When 
it reaches 4750 hours, the bar turns to red. •
•
•
INPUT .................................. Indicates the name of the terminal to which the currently projected video signal is 
being input.
RESOLUTION ...................... Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY ..... Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FREQUENCY Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE ........................ Indicates the type of the sync signal for the currently projected video signal.
AV memory
You can store up to 3 patterns of the image quality setting for each input source.
To store the settings
Set the items of the IMAGE menu.
Setting the items by using the picture quality adjusting buttons on the remote control is also available.
Press the S or T button to select AV MEMORY SAVE.
Press the W or X button to select AV MEMORY (1, 2 or 3) to store the settings. 
Press the ENTER button.
To enable the stored image quality settings
Press the AV MEMORY button to call up the stored setting.
When you make change to the stored setting you call up, the changed setting remains effective but is not 
saved to the AV MEMORY unless AV MEMORY SAVE is executed.
When the input source is changed, the AV memory setting selected just before is automatically selected.
When RESET ALL in the FEATURE menu is selected, all the settings of the AV memory are cleared. 1.
•
2.
3.
4.
1.
•
•
• 
						

							EN-30
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu.
(See page 25 for menu setting.)
Display the IMAGE menu.
Select CONTRAST or BRIGHTNESS by pressing the S or T button.
Adjust the selected item by pressing the W or X button.
To cancel the menu:
Press the MENU button.
CONTRAST
Select to adjust the contrast of the image. Every time the X button is pressed, the image becomes brighter and more 
defi ned. Every time the W button is pressed, the image becomes darker and less defi ned.
BRIGHTNESS
Every time the X button is pressed, the image becomes brighter. Every time the W button is pressed, the image 
becomes darker.
To adjust the color (COLOR and TINT):
You can adjust the color of the projected image using the menu.
(See page 25 for menu setting.)
Display the IMAGE menu.
Select COLOR or TINT by pressing the S or T button.
Adjust the selected item by pressing the W or X button.
To cancel the menu:
Press the MENU button.
COLOR
Use to adjust the color intensity of the projected image. Every time the X button is pressed, the color intensity 
increases. Every time the W button is pressed, the color intensity decreases.
TINT
Use to adjust the tint of the projected image. Every time the X button is pressed, the image appears more greenish. 
Every time the W button is pressed, the image appears more reddish.
To sharpen or soften the projected image (SHARPNESS):
You can adjust the sharpness of the projected image using the menu.
(See page 25 for menu setting.)
Display the IMAGE menu.
Select SHARPNESS by pressing the S or T button.
Adjust the selected item by pressing the W or X button.
To cancel the menu:
Press the MENU button.  1.
2.
3.
4.
1.
2.
3.
4.
1.
2.
3.
4.
Adjusting projected images