Mitsubishi Hc5000bl Projector User Manual

							EN-11
Front projection, ceiling mounting
For ceiling mounting, 
you need the ceiling 
mount kit designed 
for this projector. 
Ask a specialist for 
installation. For details, 
consult your dealer.
The warranty on this projector does not cover any 
damage caused by use of any non-recommended 
ceiling mount kit or installation of the ceiling mount 
kit in an improper location.
When using the projector mounted on the ceiling, 
set IMAGE REVERSE in the INSTALLATION menu 
to MIRROR INVERT. See page 26.
When the projector is mounted on the ceiling, 
images may appear darker than those projected in 
the case of tabletop mounting. This isn’t a product 
malfunction.
Ask your installation specialist to provide an A/C 
power switch. When you do not use the projector, 
be sure to shut down the main power by the 
switch.
Do not install the projector where the exhaust vents 
are exposed to air emitted by an air conditioning. 
Such installation may cause a breakdown.
Do not install the projector near a fi re alarm 
because it emits hot air from its exhaust vents.
Rear projection
Ask a specialist for 
installation. For details, 
consult your dealer.
For rear projection, 
set IMAGE 
REVERSE in the 
INSTALLATION menu to MIRROR. See page 26.
Caution:
Placing the projector directly on a carpet impairs 
ventilation by the fans, causing damage or 
failure. Put a hard board under the projector to 
facilitate ventilation.
Place the projector at least 50 cm (or 20 inch) 
away from the wall to prevent the air inlet grille 
and the air outlet grilles that emit hot air from 
being blocked.
Do not use the projector in the following 
locations and manners, which may cause fi re or 
electric shock.
In a dusty or humid place.
In a sideways position, or with the lens facing 
down.
Near a heater.
In an oily, smoky, or damp place such as a kitchen.
In direct sunlight.
Where the temperature rises high, such as in 
a closed car.
Where the temperature is lower than +41ºF 
(or +5ºC) or higher than +95ºF (or +35ºC ). •
•
•
•
•
•
•
•
•
• •
•
•
•
•
•
•
Setting up your projector (continued)
Important:
We don’t recommend using the projector at an 
altitude of 1500 meters or higher. Use at an altitude of 
1500 meters or higher may affect the projector’s life.
TRIGGER terminal
The TRIGGER terminal on the rear of the projector 
is a terminal that outputs a 12 V signal to control an 
externally connected device (electric screen) when 
images are projected.
To use the TRIGGER terminal, set TRIGGER OUT to 
ON in the INSTALLATION menu. (The factory default is 
OFF.) Use the following steps to change the setting.
With the INSTALLATION menu:
(See page 25 for menu setting.)
Display the INSTALLATION menu.
Select TRIGGER OUT by pressing the S or T 
button.
Select ON by pressing the W or X button.
To cancel the menu:
Press the MENU button.
Caution:
Do not use the signal output from the TRIGGER 
terminal as a power for other devices.
Do not link the TRIGGER terminal with an audio 
terminal of other device because that device may 
be damaged.
The rated current for the TRIGGER terminal is 
200 mA. If you use a current exceeding this rating, 
a failure may occur.
For information about electric screens, please 
contact screen manufacturers. •
1.
2.
3.
4.
•
•
•
•
TRIGGER
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
Ring (NC) To externally connected 
device
 Tip (12 V)
(Ground 0 V) 
						

							EN-12
Screen size and projection distance
Refer to the following table to determine the screen size. 
Screen width B
Down side
Up side
50%
50%
SCREEN
Screen height A
(H)
(H)
(L)
Right side
Left side
(W) (W)
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional 
relation between the projected image and the screen is as 
shown on the right. Refer to the following table for installation.
When the aspect ratio of the image is 16:9
Screen sizeSize of the projected imageBlack 
space (D)Projection distance (L) Lens movable range
Diagonal size Height C Width B Height A Width B Min. Max. (H) (W)
inch cm inch cm inch cm inch cm inch cm inch cm inch m inch m inch cm inch cm
50 127 30 76 40 102 23 57 40 102 4 10 55 1.4 89 2.3 17 43 2 6
60 152 36 91 48 122 27 69 48 122 5 11 66 1.7 108 2.7 20 51 2 6
70 178 42 107 56 142 32 80 56 142 5 13 78 2.0 126 3.2 24 60 3 7
80 203 48 122 64 163 36 91 64 163 6 15 89 2.3 144 3.7 27 69 3 8
90 229 54 137 72 183 41 103 72 183 7 17 101 2.6 163 4.1 30 77 4 9
100 254 60 152 80 203 45 114 80 203 8 19 112 2.9 181 4.6 34 86 4 10
110 279 66 168 88 224 50 126 88 224 8 21 124 3.1 199 5.1 37 94 4 11
120 305 72 183 96 244 54 137 96 244 9 23 135 3.4 218 5.5 41 103 5 12
150 381 90 229 120 305 68 171 120 305 11 29 170 4.3 273 6.9 51 129 6 15
200 508 120 305 160 406 90 229 160 406 15 38 227 5.8 365 9.3 68 171 8 20
250 635 150 381 200 508 113 286 200 508 19 48 285 7.2 456 11.6 84 214 10 25
300 762 180 457 240 610 135 343 240 610 23 57 342 8.7 548 13.9 101 257 12 30
The above fi gures are approximate and may be slightly different from the actual measurements.
Projection distance changes according to the setting of SCREEN SIZE in the ADVANCED MENU in the IMAGE menu. The table above is in the 
case of “16:9.” •
•
When the aspect ratio of the screen is 16:9
Screen size Projection distance (L) Lens movable range
Diagonal size Height A Width B  Min. Max. (H) (W)
inch cm inch cm inch cm inch m inch m inch cm inch cm
50 127 25 62 44 111 60 1.5 98 2.5 18 47 2 6
60 152 29 75 52 133 73 1.8 118 3.0 22 56 3 7
70 178 34 87 61 155 85 2.2 138 3.5 26 65 3 8
80 203 39 100 70 177 98 2.5 157 4.0 29 75 3 9
90 229 44 112 78 199 110 2.8 177 4.5 33 84 4 10
100 254 49 125 87 221 123 3.1 197 5.0 37 93 4 11
110 279 54 137 96 244 135 3.4 217 5.5 40 103 5 12
120 305 59 149 105 266 148 3.8 237 6.0 44 112 5 13
150 381 74 187 131 332 185 4.7 297 7.6 55 140 7 17
200 508 98 249 174 443 248 6.3 397 10.1 74 187 9 22
250 635 123 311 218 553 311 7.9 497 12.6 92 233 11 28
300 762 147 374 261 664 373 9.5 597 15.2 110 280 13 33
The above fi gures are approximate and may be slightly different from the actual measurements.
Projection distance changes according to the setting of SCREEN SIZE in the ADVANCED MENU in the IMAGE menu. The table above is in the 
case of “16:9.” •
•
Setting up your projector (continued)
C 
A 
DD
B  
						

							EN-13
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CR
PB/
CB
COMPONENT
VIDEO IN
AC IN
DVD player
A. Connecting the projector to video equipment
When the projector and the connected devices are located too close to each other, the projected image may be 
affected by their interference.
See the owner’s guide of each device for details about its connections.
Preparation:
Make sure that the power of the projector and that of the video equipment are turned off.
Basic home theater system connection
•
•
•
Video player
Set-top box or digital tuner
Viewing video images 
						

							EN-14
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
1 2 
1 2 
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
PB/CBY PR/CR 
PB/CB
Y
P
R/CR
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
Y Component cable (option)
Connect one end of the optional video cable to the VIDEO 
IN terminal of the projector.
Connect the other end of the video cable to the video 
output terminal of the video equipment. 1.
2.
Also read the instruction manual of the equipment to be connected.
Contact your dealer for details of connection.
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of NO SIGNAL 
may appear on the screen when you change the channel via any channel that is not being received. In such a case, 
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip 
function (that is a function not to display channels that are not being received) enabled.
Connecting to a DVD player or HDTV decoder
To connect this projector to video equipment that has component video output terminals, such as a DVD player, use 
the COMPONENT VIDEO IN terminals. •
•
The terminal’s names Y, P
B, and PR are given as examples of when a HDTV decoder is connected.
The terminal’s names vary depending on the connected devices.
Images may not be projected correctly depending on the type of the DVD player you use.
Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction.
When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL 
menu. •
•
•
•
•
Connecting to a video player, etc.
To video output 
terminal
Video cable (option)
S-video cable (option)
To S-VIDEO 
IN terminalTo S-video 
output terminal To VIDEO 
IN terminal
When the video equipment is equipped with the S-video 
output terminal, make the connection as follows:
Connect one end of the optional S-video cable to the 
S-VIDEO IN terminal of the projector.
Connect the other end of the S-video cable to the S-video 
output terminal of the video equipment. 1.
2.
DVD player or HDTV decoderVideo player, or the like Video player, or the like
Viewing video images (continued) 
						

							EN-15
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
HDMI IN
SERIAL DVI-D(HDCP) IN
TRIGGERCOMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
INPR/
CRPB/
CB
COMPONENT
VIDEO IN
AC IN
To audio output 
terminals
Connecting to video equipment having a HDMI terminal or DVI-D terminal
You can project high-quality images by connecting the HDMI IN terminal of this projector to video equipment having 
a HDMI output terminal or DVI-D terminal of this projector to video equipment having a DVI-D output terminal. In 
addition, this projector supports HDCP and is able to receive encrypted digital video data that are output from DVD 
players.
Select HDMI or DVI as the input source.
HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital 
video data for the purpose of copy protection.
HDMI (High-Defi nition Multimedia Interface) is fully backward compatible with computers, displays and consumer 
electronics devices incorporating the DVI standards.
This projector can be linked with video devices equipped with HDMI output terminal or DVI-D output terminal. 
However, with some of them, this projector may not display any image or not operate correctly.
If this projector doesn’t display any image or not operate correctly, see the operation manual of the video device 
for its connection.
When you use the video equipment other than HDMI conformity product, the image may not be projected 
properly.
Use of a long cable may decrease the quality of projected images.
Connection (for video equipment having an HDMI terminal)
Use a commercially available HDMI (with HDMI logo) cable.
Some cables may not be connected correctly depending on the size and shape of their connectors. 
To connect a second HDMI device, connect it to the DVI-D (HDCP) IN terminal using a DVI-HDMI conversion 
cable.  •
•
•
•
•
•
•
•
•
•
Equipment having an 
HDMI terminal
To HDMI terminal
Equipment having a 
DVI-D terminal
Connection (for video equipment having a DVI-D terminal)
Use a commercially available DVI cable. •
Images may not be projected correctly depending on the type of the video equipment you use.
Depending on the type of DVD recorder connected to the DVI-D(HDCP) IN terminal, the projected image may be 
tinted with magenta. In this case, set COMPUTER INPUT of the SIGNAL menu to YC
BCR/YPBPR. (See page 28.) •
•
DVI cable (option)To DVI-D(HDCP) IN terminal To DVI-D terminalAudio cable (option)To HDMI IN terminal To audio input 
terminals To audio output 
terminalsAudio cable (option)
HDMI (with HDMI logo) cable (option)
To audio input 
terminals
Viewing video images (continued) 
						

							EN-16
1
2
HDMI IN
SERIAL
AC IN
When you connect this projector and a DVI-Digital device (such as a DVD player) via the HDMI terminal or DVI-
D (HDCP) terminal, black color may appear dark and deep, depending on the type of the connected device.
This depends on the black level setting of the connected device. There are two kinds of methods to digitally 
transfer image data, in which different black level settings are employed respectively. Therefore, the specifi cations 
of the signals output from DVD players differ, depending on the type of the digital data transfer method they use.
Some DVD players are provided with a function to switch the methods to output digital signals. When your DVD 
player is provided with such function, set it as follows.
EXPAND or ENHANCED J NORMAL
See the users guide of your DVD player for details.
Set INPUT LEVEL of ADVANCED MENU in the IMAGE menu depending on the device to be used.
B. Plugging in the power cord
•
•
•
•
The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your 
country.
This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the 
power plug. If the power plug doesn’t fi t your wall outlet, ask an electrician to change the wall outlet.
The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply 
using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare 
an appropriate power cord separately.
Use 100-240 V AC 50/60 Hz to prevent fi re or electric shock.
Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to 
the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause 
fi re or electric shock.
Do not modify or alter the power cord. If the power cord is modifi ed or altered, it may cause fi re or electric shock.
Caution:
Plug in the power cord fi rmly. When unplugging, hold and pull the power plug, not the power cord.
Do not plug in or out the power cord with your hand wet. It may cause electric shock. •
•
•
•
•
•
•
•
Power cord (example)
Plug the attached power cord into the power cord inlet of 
this projector.
Plug the other end of the power cord into a power outlet. 1.
2.
Earthing 
terminal
Viewing video images (continued) 
						

							EN-17
Confi rm the POWER indicator lights-up red.
If the projector was turned off before the lamp had cooled down suffi ciently, the fan may start rotating and the 
POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the 
fan stops rotating, press the POWER button to turn back on the POWER indicator.
Press the POWER button on the projector or ON ( I ) button on the remote control.
It may take about one minute for the lamp to light up.
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the 
lens cap.
After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a 
product malfunction.
The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP 
MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
The projector starts warming up when the POWER button is pressed. During the warm-up process, images 
may appear dark and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when 
the STATUS indicator blinks red. (See page 41.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS”.
Adjust with the W or X button to get a fi ne picture.
Select an input source.
Press the VIDEO or HDMI/DVI button on the projector or the VIDEO, S-VIDEO, COMPONENT, HDMI or DVI 
button on the remote control that is corresponding to the terminal in use.
The input source is switched between VIDEO, S-VIDEO and COMPONENT every time you press the VIDEO 
button on the projector.
The projector automatically selects the appropriate signal format. (The selected signal format is displayed on 
the INFORMATION menu.)
You cannot change the input source while the menu is being displayed.
Though it may take some time before an image is displayed on the screen depending on the type of the input 
signal, such symptom is not a malfunction.
Some images become easier to view when the setting of aspect ratio is changed. (See page 20.)
Adjust the position of the projector to keep an appropriate projection distance with which images are projected in 
their specifi ed sizes.
Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 
10.)
Press the ZOOM/FOCUS button on the projector or on the remote control to display “FOCUS” and then press the 
button again to display “ZOOM.”
Adjust with the W or X button to get an approximate size.
Press the LENS SHIFT button. “LENS SHIFT” will appear on the display.
Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the 
displayed image.
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 
10.)
Repeat steps 3 to 4 and 8 to 11, if necessary.  1.
•
2.
•
•
•
•
•
•
•
3.
4.
5.
•
•
•
•
•
•
6.
7.
8.
9.
10.
11.
•
C. Projecting images
Preparation:
Remove the lens cap.
Turn on the power of the connected video equipment. •
•
Viewing video images (continued)
VIDEO button POWER buttonCOMPONENT button
VIDEO button S-VIDEO button ON ( I ) button
DVI button
LENS SHIFT button ZOOM/FOCUS button ZOOM/FOCUS buttonHDMI button
LENS SHIFT button 
						

							EN-18
POWER button
To stop projecting:
Press the POWER button on the projector or the OFF () button on the remote control.
A confi rmation message is displayed.
To cancel the procedure, leave the projector for a while or press the MENU button.
Press the POWER button on the projector or the OFF (
) button on the remote control again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green.
Wait about 2 minutes.
During this period of 2 minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
The lamp can’t be lit again for 1 minute after turning off the projector for safety purpose. It will take another 1 
minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator 
goes out, and then press the POWER button.
The air outlet fans rotate faster as the temperature around the projector rises.
Do not unplug the power cord while the STATUS indicator is blinking. Unplugging the power cord immediately 
after use may cause a lamp breakdown.
Though the fan makes loud sound during cooling, such symptom is not a malfunction.
Unplug the power cord from the outlet.
The POWER indicator will go out.
If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are 
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the 
lamp again, press the POWER button. If the lamp doesn’t light up immediately, repeat pressing the POWER 
button two or three times. If it should still fail to light up, replace the lamp.
Cover the lens with the lens cap to protect it from dust. 12.
•
•
13.
•
14.
•
•
•
•
•
15.
•
•
•
OFF () button
Viewing video images (continued) 
						

							EN-19
Viewing video images (continued)
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the 
setting according to the type of the input video signal.
 : Signal size   : Image area
Original image size
4:3 16:9 ZOOM1 ZOOM2 STRETCH
Aspect ratio 
changes 
depending on the 
input signal.Squeezed image is 
expanded to 16:9. CinemaScope image is 
enlarged and displayed 
together with subtitles.Vista image is enlarged 
and displayed together 
with subtitles.Image is enlarged to 
16:9 while the center 
aspect ratio remains 
unchanged. 
4:3 image (480i, 
576i, 480p, 576p, 
and PC)
Squeezed 4:3
(480i, 576i, 480p, 
576p)
4:3 CinemaScope
(480i, 576i, 480p, 
576p)
Sub TitleSub TitleSub TitleSub TitleSub TitleSub Title
4:3 Vista image
(480i, 576i, 480p, 
576p)
16:9 image
(720p, 1080i, 
1080p)
Bold frames are recommended modes.
When ASPECT is set to AUTO, an optimum aspect ratio is automatically selected depending on the input signal.
When ASPECT is set to ZOOM1 or ZOOM2, display position can be changed with S or T button on the remote 
control.
OVER SCAN in the SIGNAL menu is not available in the STRETCH mode.
Display pattern changes according to the setting of SCREEN SIZE in the IMAGE menu. The table above is in the 
case of “16:9.”
This projector is equipped with a function to change the aspect ratio. If you select an aspect ratio that is 
inconsistent with that of the input signal, images around the screen edges may be hidden or deformed. When 
viewing original video works refl ecting the authors’ intentions, you are recommended to keep their aspect ratios 
unchanged.
It may be an infringement of the rights protected by the copyright law to project images compressed or enlarged 
by changing the aspect ratio in public areas, such as inside and outside shops and hotels, for commercial or 
public viewing purposes.
When SCREEN SIZE of ADVANCED MENU is set to CINEMA SCOPE(2.35:1) in the IMAGE menu, STRETCH 
cannot be selected for ASPECT. •
•
•
•
•
•
•
• 
						

							EN-20
How to change the settings:
With the remote control:
Press the ASPECT button.
Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 4:3, 16:9, to ZOOM1, to 
ZOOM2, to STRETCH, and back to AUTO.
Some modes are not available with certain signals.
With the FEATURE menu:
(See page 25 for menu setting.)
Display the FEATURE menu.
Select ASPECT by pressing the S or T button.
Select your desired aspect ratio by pressing the W or X button.
To cancel the menu:
Press the MENU button.
Important:
When a 4:3 image is kept displayed for a long time before displaying 16:9 image, the afterimages of the black bars 
may appear on the 16:9 image screen. (See page 39.) 1.
•
•
1.
2.
3.
4.
•
FE A TURE 
AUTO
opt.
ASPECT
A V MEMO R Y 1 
Viewing video images (continued)