Mitsubishi Electric Wd 65735 Owners Guide

							
 Appendices 101
 Appendices 101

Appendix D:  Troubleshooting, continued
IEEE 1394 Devices
Symptom Remarks
3. There is no audio and video from the IEEE 
1394 device. •  The device is not turned on.  Turn the device power on.
•  No media (tape or disc) is inserted into the device.
•  The media is blank (has no recording).
•  The play command failed - Try pressing play again on the 
device’s remote control or front panel.
•  The device is already in use (for example, the device is cur
-
rently recording).
•  The source is copy-protected or violates copy protection.
•  The device’s digital video signal is not supported by the TV,  as may be the case with an IEEE 1394 signal from a com
-
puter.  Use analog connections instead, if available.
•  The device is not an audio/video device.
•  Too many other devices are already communicating over IEEE  1394.  Remove or stop some devices and try again.
4. The IEEE 1394 Device is no longer listed in 
the Input Selection menu. •  The IEEE 1394 plug is disconnected or loose.
•  The IEEE 1394 device has not been powered on.  Turn on.
•  The device has not been discovered.
•  The device is not an audio/video device
5. The IEEE 1394 device cannot be selected (is 
grayed out). •  The device may be busy with a recording.  Cancel the record
-
ing.
•  You have connected more than seven IEEE 1394 devices.   Unplug the eighth device and one other device.  Plug the 
eighth device back in.
6. MENU button does not display a menu. •  The IEEE 1394 device does not provide a menu.
•  The TV cannot support IEEE 1394 menus.
7. All IEEE 1394 devices disappear. •  The connected devices must not be in a loop that returns to 
the TV.  Make sure a device is connected at the end.
•  Disconnect all the cables and devices from the TV.  Replace  them one by one to locate the problem device or cable.
•  Use System Reset (front control panel).
8. Cannot rediscover a deleted IEEE 1394 
device. The device has been disconnected.  Plug it in.
9. An IEEE 1394 device has been plugged in 
but does not appear in the Input Selection 
menu (not discovered). •  The IEEE 1394 connection to the TV or another device is not 
secure or is loose.
•  The IEEE 1394 device is not powered on.
•  A device in the IEEE 1394 chain is not powered on.  Turn on  all the devices.
•  The device discovery can take as long as a minute to initiate.
•  IEEE 1394 cable is too long (maximum of 15 feet  between  devices).
•  The IEEE 1394 device uses an incompatible protocol and will  not be discovered
10. Cannot view video from an IEEE 1394 DV 
camcorder. Use analog connections for video and audio.  You can still use the 
IEEE 1394 connection for control functions, however.
11. An IEEE 1394 device is not responding 
properly. •  Unplug the device’s power cord.  Wait at least ten seconds 
and plug it in again.
•  Some IEEE 1394 devices are not supported by the TV  because of incompatible standards.
 
						

							
102 Trademark and License Information
102 Trademark and License Information

LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, 
IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT  NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE.
CableCARD™ is a trademark of Cable Television Laboratories, Inc.
CompactFlash® and CF are trademarks of the CompactFlash Association. DCR™ Certification Logo is a trademark of the Consumer Electronics Association.
Digital Light Processing™ and DLP™ are trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories.  Dolby is a trademark of Dolby Laboratories. DTVLink™ Certification Logo is a trademark of the Consumer Electronics Association.
Firewire® is a trademark of Apple Computer, Inc. registered in the U.S. and other countries.
HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI 
Licensing LLC.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual prop
-
erty rights.  Use of this copyright protection technology must be authorized by Macrovision, and is intended for home  and other limited pay-per-view uses only unless otherwise authorized by Macrovision.  Reverse engineering or disas
-
sembly prohibited.
This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license  from Microsoft Licensing, Inc.
MultiMediaCard™ is trademark of Infineon Technologies and licensed to the MultiMediaCard Association.
The    logo and the words “Simplay™” and “Simplay HD™” are the trademarks of Silicon Image, Inc.
XBox™ is a trademark of the Microsoft Corporation. ChannelView™, ClearThought®, NetCommand®, PerfectColor™, QuickView™, ViewPoint® are trademarks of  Mitsubishi Digital Electronics America, Inc.
Trademark and License Information
 
						

							
 Trademark and License Information 103
 Trademark and License Information 103

Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and 
Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”).   By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws  and treaties.  The Software is licensed, not sold.
1.  LICENSE GRANT.  MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software 
only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.  RIGHTS AND LIMITATIONS.
Software Not for Resale.  You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the T V that 
Software has been pre installed. Prohibition on Reverse Engineering, Decompilation and Disassembly.  The Software contains trade secrets or other proprietary material  in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the 
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components.  The Software is licensed as a single product.  Its component parts may not be separated for use on more 
than one T V.
No Rental .  You may not rent, lease, lend, or sublicense the Software.
Trademarks .  This License Agreement does not grant you any rights to any trademarks of MDEA.
3.  VIOLATIONS.  You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License, may 
subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any 
violation of this License.  You further understand that you may be held legally responsible for any copyright infringement or other violation 
of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License.  This license  is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any 
provision of this License.
4.  COPYRIGHT.  All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, 
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are 
owned by or licensed to MDEA.  All title and intellectual property rights in and to the content which may be accessed through use of the  Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws 
and treaties.  This License Agreement grants you no rights to use such content, except that you own the media on which the Software is  recorded, but MDEA and its licensors retain ownership of the Software itself.  All rights not expressly granted are reserved by MDEA.
5.  EXPORT RESTRICTIONS.  MDEA is licensing the Software for use within the United States.  You agree that you will not export 
or re-export the Software.  You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has 
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq,  Libya, North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the 
Software back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, 
development, or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from  participating in U.S. export transactions by any federal agency of the U.S. government.  You warrant and represent that neither the BX A nor any other U.S. federal agency has suspended, revoked, or denied your export privileges.
6.  DISCLAIMER OF WARRANTY.  EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY 
APPLICABLE TO THE TV, MDEA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE 
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH  RESPECT TO THE SOFTWARE.  ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MDEA .  IN  NO EVENT SHALL MDEA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY 
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE.   BECAUSE SOME 
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY  NOT APPLY TO YOU.
7.  LIMITATION OF LIABILITY.  MDEA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD 
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR 
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES  MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE.  YOU AGREE THAT NEITHER MDEA’S 
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE 
ESSENTIAL PURPOSE OF THIS LICENSE.  BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION 
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.  MDEA’s  liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the 
money paid by you for the TV (based on fair market value of the TV ) that caused the damages.
8.  GENERAL.  This License Agreement will be governed by the laws of the State of California.
WARNING:  This product contains chemicals known to the State of California to cause cancer and/or birth defects 
or other reproductive harm. 
 
						

							
104 
104 

Mitsubishi DLP™ Projection Television Limited Warranty
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this 
television from an authorized MITSUBISHI Audio/ Video Dealer, should it prove defective by reason of against defects 
arising from improper workmanship and/or material:
a. Parts.  The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a 
period of thirty (30) days from the date of the original purchase at retail.  The lamp and all other parts (except any soft
-
ware incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at 
retail. We will repair or replace, at our option, any defective part without charge for the part.  Parts used for replacement 
may be replaced with those of like kind and quality and may be new or remanufactured.  Parts used for replacement are 
warranted for the remainder of the original warranty period.
b. Embedded Software.  MDEA warrants that all software incorporated into this television set (the “Embedded Soft
-
ware”) will perform in accordance with the functional description of Embedded Software in all material respects, but 
MDEA does not warrant that the Embedded Software is error-free.  MDEA also does not warrant that the Embedded 
Software will be compatible under IEEE 1394 AV/C and HAVi software standards with products produced by any other 
manufacturer.  The limited warranty contained in this section shall continue for a period of one (1) year from the date of 
the original purchase at retail.  If, after prompt notice within the warranty period, MDEA determines that the Embedded 
Software has failed to perform in accordance with such functional description in all material respects and if such failure 
is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or 
replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled 
by means of modification or replacement software contained on a replacement memory card for Customer installation.  
The foregoing shall be MDEA’s sole obligation to you under this limited warranty.  All rights under this limited warranty 
on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License 
Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the 
Embedded Software is modified or changed in any manner except as specifically authorized by MDEA.
c. Labor.  For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular 
screen if it proves defective.  For certain items that are designed to be replaced by the consumer, including (but not 
limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, 
we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) 
year from the original date of purchase at retail.
d. Notice.  To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within 
the applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image 
using small dots, or picture elements (pixels).  Your DLP Projection TV is manufactured to a high level of performance 
and quality, in fact, 99.99% perfect in the number of properly functioning pixels.  As in other display technology, some
-
times a pixel is continuously active, inactive or the incorrect color.  Our standard is clear; MDEA warrants only that the 
percentage of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct 
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your 
MITSUBISHI dealer, by writing at the address provided below, calling MDEA at the 800-332-2119, or by using the 
support feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your 
television is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If 
not, you must either deliver your television to an authorized service location at your own expense, or pay for any travel 
and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided 
without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present 
your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER 
REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please 
return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you.
 
						

							
  105
  105

d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278.
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b.  Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such 
damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than 
an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry 
out any maintenance as described in the Owner’s Guide including air filter cleaning or any product damaged by exces
-
sive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or 
removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts 
of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical 
system or lightning.  This limited warranty also excludes service calls where no defect in the product covered under this 
warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in 
the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product 
installation, or set-ups, any adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharp
-
ness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, 
antenna, cable or satellite systems, or service of products purchased or serviced outside the U.S.A.  Please consult the 
operating instructions contained in the Owner’s Guide furnished with the product for information regarding user con
-
trols.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, 
MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY 
LIMITED TO A TERM OF ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY 
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, 
BREACH OF CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental, 
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to 
state.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
 
 
						

							
106 Index

Index
A
A / V Discs  85
A / V Memory Reset. See Reset
A / V Receiver Connecting  
31
A / V Reset. See Reset
Adjust Keys (Up/Down/Left/Right)  
34, 44
Anamorphic Picture Format DVD Definnitions  
38
Antenna Adjusting and the Signal Strength Meter  
49
Connecting  
27
Antenna Inputs (ANT 1/MAIN, ANT  2/AUX)  
18
Audio/ Video Menu  
45, 57
Audio Settings  
58
Auto Input Sensing  
22
B
Back Panel (illustrated)  18, 19
Batteries. See Remote Control
C
CableCARD™  13, 17, 18, 46
Cable Box and the Remote Control  
34, 62
Connecting  
25, 29, 32
IEEE 1394  
80
Camcorder Connecting (Analog)  
32
DV (Digital Video)  
81, 101
IEEE 1394 Camcorders  
81
Power  
80
Captions Menu  
45, 51
Channels. See also FAV and TV Timer  
47
Changing  
14
Digital Channel Numbers  
91
Memorizing  
46
Naming  
49
Status Display  
37
ChannelView™ Channel Listings  
36
Channel Menu  
45, 49
Cleaning  
7
ClearThought® Auto Input Sensing  
22
Clock, Set Date and Time  
46
Closed Captions. See Captions Menu
Color Adjustments  
59
Component Inputs (Y Pb Pr)  
19, 58
Computer. See Personal Computer
Connection Types  
23
Copy Restrictions  
85
and Status Display  
37
D
Date. See Clock
Daylight Savings Time  
46
Digital Audio Out  
19
Display Format Definitions  
38
Dolby Digital  
19, 31, 92
and IEEE 1394  
80
DTVLink™  
19
DV  
81
DVDs and the Remote Control  
34, 62
and V-Chip Ratings  
56
DVD Player with Component Video,  Connecting  
31
DVI Device, Connecting  
30
DVI Jack (for Personal Computer)  
19
E
Energy Mode  47
F
Fan Noise  6
Fast Power On (Energy Mode)  
47
FAV  
50
Film Mode  
57
FireWire®. See IEEE 1394
Freeze Picture. See Pause
Front Panel Lock  
53
G
GUIDE Key (button)  34
H
HDMI HDMI Device  
30
HDMI Inputs  
12
HDMI Jack  
58
HDMI Jack, Description  
19
Personal Computer with HDMI  Output  
75
Remove the Icon for an HDMI  Device  
48
HDTV Receiver with Component  Video, Connecting  
25
HD (High-Definition Signal)  
38
I
Icon Order Menu  45, 48
IEEE 1394 Devices and Analog Outputs  
22, 86
and Recording  
82
and Status Display  
37
Compatible IEEE 1394 Devices  
80
Connecting IEEE 1394 Devices  
81
HAVi Amplifiers  
58, 81 Inputs on TV  
19
TV Connection Speed  
81
INFO Key Status Display  
37
Input Jacks on TV (Standard Audio/ Video)  
18, 58
Input Name Menu  
45, 48
Input Selection Menu Remove the Computer Icon from the Input Selection Menu  
74, 75
Remove the Icon for an HDMI  Device  
48
L
Lamp Cartridge Replacement  93
LAMP Indicator. See LED Indicator  Lights
Language Audio Setting (Digital Channels)  
58
for TV Menus  
46
LED Indicator Lights LAMP Indicator  
16
POWER/ TIMER Indicator  
16
STATUS Indicator  
16
Troubleshooting  
99
Lock TV. See Parental Lock
Low Power (Energy Mode)  
47
M
Memorizing Channels  46
MONITOR OUT Jacks  
19
MP3 Audio  
80
Mute Audio
and Closed Captions  51
and status Display  
37
MUTE key  34
Video Mute  
57
N
Noise Reduction (Video)  59
P
Parental Lock Bypassing  
89
Front Panel Lock  
53
V-Chip Ratings  
56
Pass Code Resetting  
89
Setting  
53
PAUSE Key  
34
PerfectColor  
59
Personal Computer  
81
and Display Formats  
38
Connecting  
75
Remove the Computer Icon  
74, 
75
 
						

							
 Index 107

Setup  74
Picture Quality and Connection Types  
24
and Film Mode  
57
Troubleshooting  
98
Power Consumption  
47, 92
Power On/Off  
14, 98
Q
QV (QuickView™)  34
R
Recording and MONITOR OUT Jacks  
19
and Split Screen  
19
Cancelling Recordings
IEEE 1394 devices  83
Recording Setup Menu
and IEEE 1394 Devices  82
RECORD Button  100
Record List
and IEEE 1394 Devices  82
Signals Available for Recording  
23
Remote Control Batteries  
35
Keys and Functions  
34
Programming Codes (reference  chart)  
64
Programming Instructions  
63
Reset  
35, 64
Reset A / V (all settings)  
15
A / V Memory (for individual de
-
vices)  
57
DVCR Counter  
84
Pass Code  
89
PerfectColor  
59
Remote Control  
35, 64
Summary Table  
95
System Reset Button  
15
S
S-Video Connecting  
25
Connector Illustration  
24
Safeguards  
8
SAP (Second Audio Program)  
58
Satellite Receiver and the Remote Control  
62
Connecting  
25
SD (Standard-Definition Signal)  
38
Search A / V Disc. See A / V Discs
Service and Support  
96
Setup Menu  
45, 46
Signal Definitions  
38 Sleep Timer  
35
Speakers, Turning TV Speakers On or  Off  
57
Specifications, TV  
91
Split Screen and Recording from MONITOR OUT  
19
Description  
40
Stand, TV  
6
Standard-Definition Signal  
38
Status Display  
37
STATUS Indicator. See LED Indicator  Lights
Stereo System. See A / V Receiver
System Reset  
15, 96
T
3:2 pulldown  57
Time. See Clock
Timer (TV Timer)  
47
Time Zone. See Clock
Troubleshooting  
95
V
VCR Connecting  
18, 28, 29
IEEE 1394  
80
Troubleshooting  
99
Video Noise Reduction  
59
Video Settings  
59
Viewing Device. See Input Selection  Menu
W
Wall Outlet Cable  26
 
						

							
© 2006 Mitsubishi Digital Electronics America, Inc. Written and Printed in U.S.A.
853B542B10   V33
Website:
www.mitsubishi-tv.com
E-mail:
[email protected]
For questions, call Consumer Relations at
800-332-2119
To order replacement or additional
remote controls, lamp cartridges, or Owner’s Guides
Visit our website at www.mitsuparts.com or call
800-553-7278
Demo Mode
This TV has a demo mode for use in retail stores.  
Demo mode causes the TV to display a series of 
screens outlining the TV’s features.
To turn off demo mode:
1.  Press 
MENU.
2.  When the Main menu appears with Setup high
-
lighted, press 
ENTER.
3.  When the Setup menu opens, press  to high-
light the on-screen Demo Mode Off button.
4.  Press 
ENTER.
System Reset
If the TV does not respond to the remote control, 
front panel controls, or will not power on/off, press 
the 
SYSTEM RESET button on the front panel with a 
pointed object, such as the point of a pencil or end 
tip of a paperclip.
The green LED will flash quickly for about one 
minute.  When the green LED stops flashing, you 
may turn on the TV.