Mitsubishi CP D2E User Manual

Safety regulations
Read this first
EN-11
WARNING
Do not use the printer with an AC adapter or power cord other 
than that specified/provided
Do not use the provided AC adapter or power cord with any 
other devices
Provide correct voltage
Incorrect voltage may damage printer parts.
Use with incorrect voltage may cause fire or electric shock.
Connect the power cord correctly/safely
If the power cord is plugged in loosely, it may cause a fire or electric shock.
Push the plug all the way into the outlet....

Safety regulations
Read this first
EN-12
 CAUTION
Ensure there is adequate ventilation around the printer
Do not put the printer where there is poor ventilation, or on a soft surface such as a rug 
or bed.
Do not put the printer on an unstable surface
Do not put the printer on an unstable surface such as a shaky table. Injury may result 
from the printer being dropped or falling. This could also damage the printer or cause 
the printer to malfunction.
Do not touch the non-user-serviceable parts inside...

Precautions
Read this first
EN-13
Precautions
When condensation occurs
Condensation is the occurrence of water droplets forming on surfaces, and may occur under the following 
conditions:
The room where the printer is located is heated quickly.
Cool air from an air-conditioner blows directly onto the printer.
The printer is moved from a low-temperature location to a high-temperature location.
When condensation occurs, print paper may become moist. This may cause printing quality deterioration or...

Precautions
Read this first
EN-14
Appropriate installation locations
Install the printer on a flat stable surface. Allow for suitable clearance around the printer. 
Notes
A space of at least 100 mm (4) is required behind the printer because paper is partially ejected from the rear of the printer 
during printing.
The cables on the rear of the printer should be directed straight out or away from the printer so they wont interfere with 
paper during printing.
at least 100 mm
(4)
Downloaded From...

Checking the contents
Read this first
EN-15
Checking the contents
Check for the following contents when unpacking the printer.
If one or more accessories are missing, contact your dealer.
AC adapter (1)Power cord (1)Paper-cassette
USER’S MANUAL (this book) (1)
CP-D2E software CD-ROM 
(printer driver) (1)
Downloaded From ManualsPrinter.com Manuals 

Parts and controls
Read this first
EN-16
Parts and controls
Front 
Rear
Downloaded From ManualsPrinter.com Manuals 

Parts and controls
Read this first
EN-17
NumberNameFunction
APower button Turns the power on/off (gpage 18).
BPower indicator Indicates the power is on/off (gpage 18).
CPAPER indicator Blinks when a paper error occurs (gpage 33).
DRIBBON indicator Blinks when a ribbon cartridge error occurs (gpage 33).
EAccess indicator Indicates the printer status (gpage 33).
FPaper-cassette door Open this door when you install or replace the paper-cassette 
(gpage 22).
GPaper-cassette door tab Use this tab when opening...

Plugging in to an outlet and turning the printer on/off
Preparation
EN-18
Preparation
Plugging in to an outlet and turning the printer on/
off
1Plug the power cord into the AC adapter. 
2Plug the power plug into a wall outlet, and then plug the DC plug into the DC-IN jack.
3Press the Power ( ) button.
The Power indicator turns on.
Press the Power ( ) button.
The Power indicator turns off.
Note
If the DC plug is accidentally unplugged from the printer during printing, turn the printer off, plug the DC...

Loading the ribbon cartridge
Preparation
EN-19
Loading the ribbon cartridge
About the paper/ink ribbon set
For printing, paper/ink ribbon set (not supplied) are required.
For details, refer to “About the paper/ink ribbon set” (gpage 38).
Setting the ribbon cartridge
1
Open the ribbon cartridge door. 
2Remove slack from the ribbon.
If the ribbon cartridge has been used before, take in any ribbon slack before loading.
Notes
Use ribbon cartridges and paper that are packaged together.
Do not use paper that...

Loading the ribbon cartridge
Preparation
EN-20
3Insert the ribbon cartridge into the printer following the direction of the arrow, and 
then close the ribbon cartridge door completely.
Push the cartridge in until it clicks.
If the ribbon cartridge door cannot be closed completely, take out the ribbon cartridge and then 
reinsert it.
Removing the ribbon cartridge
Open the ribbon cartridge door, and raise the tab. When the ribbon cartridge comes free, take it out. 
Note
When opening the ribbon cartridge...