Mitel Sx 100, Sx 200Superswitch Volume III Generci 217 Instructions Manual

QUANTITY OF PROGRAMMING FORMS 
PART 1 
FORM NAME NUMBER 
OF PAGES PART 2 
FORM 
NAME NUMBER 
OF PAGES 
CUSTOMER CHANGES 
SYSTEM OPTlONS 
FEATURE - 
CLASS OF SERVICE OPTIONS 
EXTENSIONS 
EXTENSION RANGE 
PROGRAMMING 
HUN-T GROUP 
NON DIAL-IN TRUNKS 
DIAL-IN TRUNKS 
- 
DID CCSA TRUNKS 
TRUNK GROUPS 
TRUNK CARD SWlTCH 
SETI-ING - CO TRUNKS 
TRUNK CARD SWITCH 
SETTINGS E AND M/TIE 
TRUNK CARD 
TRUNK CARD SWlTCi 
SmINGS 7 DID/TIE TRUNK 
CARD 
ABSORB PLAN 
CLASS OF RESTRICTION 
CONTROL PLAN 
4 ENTRY EXCEPTlON...

.:_ 
..-;. 
.f‘ 
:1.. 
54 
:: 
F 
-2.002 TO ENTER OR EXIT Standard or Extended Programming 
FOLLOW THE PROCEDURE BELOW 
CAUTlON 
THE DATA OF THE FOLLOWING FORMS CAN BE 
ENTERED A-R THE CONSOLE HAS BEEN 
PLACED IN THE DESIRED PROGRAMMING MOOE 
(STANDARD OR OCTrNDEDl 
TO ENTER STANOARD PROGRAMMING MOO-Z 
t 
I 
SET THUMBWHEEL SWITCHES TO 777X 
(WHERE X IS THE PROGAMMING CONSOLE) PRESS LAMP 
I I  TEST LAMP TEST LED LIT 
I I I 
I 
OR 
I 
DIAL FEATURE ACCESS CODE FOR FEATURE NUMBER 29 FROM THE CONSOLE - LAMP...

2.003 THE FOLLOWING PROCEDURE 
MUST BE USED WHEN INITIALLY PROGRAMMING THE SYSTE 
THIS PROCEDURE 
WILL INITIALIZE THE 
RAM AND DESTROY 
AU INFORMATION 
1. SET THE MlJM&VHEEL 
SWITCHES ON THE TONE 
CONTROL CARD TO 777X 
WHERE X IS THE IOENTlFlCATlON NUMBER 
OF THE CONSOLE BEING USED 
2. PRESS 
LAMP 
El 
LAMP TEST LEO LIT.SYSTEM 
IN STANDARD PROGRAMMING MODE 
3. PRESS 
I I 
NEXT - LAMP TEST L!3 FLASHING. 
SYSTEM IN EXTETENOED PROGRAMMING MOOE 
. 
4. SET THE THUMBWHEEL 
SWITCHES ON THE TONE 
CONTROL CARD TO...

2.004 TO INiilALlZE A SPECIFIC DATA BLOCK 
CAUTION 
THIS PROCEDURE 
WILL INITlALlZE 
THE SECTION OF RAM 
SELECTED AND RESULT IN THE LOSS 
OF ASSOCIATED CUSTOMER 
PROGRAMMING 
1. IF THE SYSTEM HAS BEEN PREVIOUSLY PROGRAMMED DIAL 
THE PROGRAMMING SECURIN CODE (FEATURE NUMBER 29) 
OR SET THE THUMBWHEEL SWITCHES ON THE TONE CO’NTROL 
CAR0 TO 777X (WHERE X IS THE CONSOLE NUM8ERt 
LAMP 
cl 
LAMP TEST LED LIT. 
2. PRESS TEST SYSTEM IS IN STANDARD 
PROGRAMMING. MODE 
3~. PRESS NEXT 
cl LAMP TEST LED FLASHING...

6. REPEAT STEPS 4 AND 5 FOR ADDITIONAL 
INITIALIZATIONS. IF REQUIRED. 
IF AU DATA BLOCKS 
HAVE BEEN ENTERED PRESS THE 
RESET BU-iTON ON THE SCANNER 
CARD - SYSTEM RESETS AND EXITS 
PROGRAMMING MODE. TO ENTER 
STANQARD PROGRAMMING MODE 
REPEAT STEPS 1 AND 2 TO ENTER 
EXTENDED PROGRAMMING MODE 
REPEAT STEPS 1.2 AND 3 A: 
THEN SET THUMBWHEEL SWITCHES TO 8888. 
. .  

. . : 
.q; 
? 
c 
B J c 
. - 
PROGRAMMING FORMS PART 1 
FORM 
NAME 
CUSTOMER CHANGES 
SYSTEM OPTlONS 
FEATURE 
CUSS OF SERVICE OPTION 
EXTENSIONS 
EXTENSION RANGE 
PROGRAMMING 
HUN7 GROUP (AGENT/RECORDING 
GROUPS) 
NON DIAL-IN TRUNKS 
DIAL-IN TRUNKS 
DID CCSA TRUNKS 
TRUNK GROUPS 
TRUNK CARD SWITCH 
SEITING - CO TRUNKS 
TRUNK CARD SWITCH 
SEITINGS E AND M/TIE 
TRUNK CARD 
TRUNK CARD SWITCH 
SEl7INGS - DID/TIE TRUNK CARD 
ABSORB PLAN 
CLASS OF RESTRICTION 
CONTROL PLAN 
4 EM-RY EXCEPTION TABLE 
20 RANGE...

SYSTEM OPTIONS MITEL 
AU0 
0 OPTION 
cl 
0 OPTION cl A00 
DIAL DIAL 
L OPTION OPTION 
L 
NUMBER NUMBER 
I 1 1100-3391 IlOO-339) 
OPTION NAME OPTION 
OPTION NAME OPTION 
NUMBER NUMBER 
4TTENDANT RELATED OPTIONS ATTENDANT TIMED RECALL - OONT ANSWER 10s 
125 
4TTENOANT BELL OFF BUTTON ENABL E - 100 
ATTENDANT TIMED RECALL - OONT ANSWER 20s .0-126 
JTTENOANT BOTH BUTTON ENABLE J 101 
ATTENDANT TtMEO RECALL - DONT ANSWER 40s 127 
ITTENDANT BOTH MODE STANDARD 102 
ATTENOANT TIMED RECALL - HOLD 20s 128...

? ‘.” :, ‘. 2s. 
@ 
CUSTOMER CHANGES 
MITEL 
I 
L 
I I 
cusloME13 NAME: 
CUSTOMER SITE: 
DATE OF CHANGE SERVICE PERSON TYPE OF CHANGE REMARKS  

CUSTOMER CHANGES 
MITEL 
CUSTOMER NAME: 
CUSTOMER SITE: 
DATE OF CHANGE SERVICE PERSON TYPE OF CHANGE 
REMARKS  

‘LY / 
SYSTEM OPTIONS 
w OPTION 
a3 MIT-EL 
cl 
OPTION 
DIAL 
OPTION 
NUMBER 
(100-3391 
zq  (loo-3391 
IPTION 
RJMEER OPTION NAME 
53 CANNOT OIAL TRUNK AFTER FLASH 
54 
CANNOT DIAL TRUNK AFTER FLASH IF HOLDING 
55 OR IN CONFERENCE WITH TRUNK 
56 DISCRIMINATING DIAL TONE b 
51 DISCRIMINATING RINGING 
56 00 NOT DISTURB ENABLE Y 
59 
EXTENSION NON - CO TRUNK TO 
60 TRUNK CONNECT ENABLE  OPTION NAME 
DIGIT TRANSLATION PLAN I 
DIGIT TRANSLATION PLAN 2 
OIGIT TRANSLATION PLAN 3 
FLEXIBLE NIGHT SERVICE v...