Miele Wt 2679 I Wpm Operating Instructions

Front view
aInlet hose (with flexible, waterproof
metallic outer sleeve)
bElectrical connection
c-fFlexible drain hose (with
detachable swivel elbow)
gControl panelhDetergent dispenser drawer
iDrum door
jAccess panel to the fluff filter and the
drain pump
kAccess panel to the emergency door
release and drainage
lFour height adjustable screw feet
Installation and connection
61
 

Rear view
aProtruding lid for holding when
moving the machine
bElectricity supply cable
cTransit bar covers
dInlet hose (with flexible, waterproof
metallic outer sleeve)
eDrain hose
Installation and connection
62
 

Installation surface
A concrete floor is the most suitable
installation surface, being far less prone
to vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
^The machine must be level and
securely positioned.
^To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
^We recommend a plywood base (at
least 59x52x3 cm) The base should
span several joists and be bolted...

^Using the spanner supplied turn the
left-hand transit bar 90°, then
^
withdraw the transit bar.^Turn the right-hand transit bar 90°,
then
^
withdraw the transit bar.
Installation and connection
64
 

,To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
^Fit the covers on to the two holes.
Then plug the holes as shown with
the caps.
,The machine must not be moved
without the transit fittings in place.
Store them in a safe place for future
use. They must be re-fitted if the
machine is to be moved again (e.g.
when moving house).
Re-fitting the transit bars
Re-fitting is carried out byreversing the
procedure.
Installation and connection
65
 

Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.
False values may also show in the Load
and Detergent display.
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.^Using the spanner supplied turn
counter nut2in a clockwise direction.
Then turn counter...

Building under a continous worktop /
in a kitchen run
,Abuilding-under kit(available
to order) with a cover plate to
replace the machine lid is required.
It must be fitted by suitably qualified
person to ensure electrical safety.
N.B. If you wish to push your machine
under a worktop and there is space to
do thiswithout removing the lidthe
building under kit is not necessary.
Otherwise the building under kit is
essential.
The building-under kit is supplied with
its own installation instructions.
–
Slides...

Fitting a decor panel
The door has a decor frame for fitting a
decor panel (available as an optional
accessory).
Decor panel dimensions
Width..............590mm(-1mm)
Height.............590mm(-1mm)
Thickness...............0.6-4mm
^Open the door.
^Unscrew the 4 screws on the upper
decor strip (see illustration).
^
Then take the upper decor strip off by
pulling itforwards.
^
Loosen but do not unscrew
completely, the screws on the three
remaining decor strips.^Move the decor strips forwards.
A decor panel...

Shortening the door panel
You can shorten the door panel to
match the height of adjacent kitchen
unit door fronts.
First of all you need to calculate
measurementX. This is the distance
from the lower edge of the machine
door to the lower edge of an adjacent
kitchen unit door front.Procedure
^Open the door.
^First remove the door panel:
– to do this unscrew the 10 screws
(see arrows) from the inside machine
door.
^Then remove the three decor strips
from the door panel:
– to do this unscrew the screws....

Fitting a plinth facing
The gap between the lower edge of the
machine plinth and the floor can be
closed up using a suitable kitchen
furniture plinth facing.
The washing machine plinth has a
special groove in which a plinth facing
can be fitted.
Plinth facing dimensions
Length
: 592 - 596 mm
Thickness
:8mm
Height (
H): The plinth facing height
must be calculated after aligning the
height of the machine with the screw
feet or after fitting the height-adjustment
frame(s).Installation
^Calculate height (H)...