Miele Wt 2670 Wpm Operating Instructions

							Load Consumption data
Energy Water Duration
in kWh in litres Short Normal
Washing
Cottons95°C 5.0 kg 1.70 42 1 h 53 min 2 h 08 min
60°C1)5.0 kg 0.85 42 1 h 29 min 1 h 58 min
40°C1)5.0 kg 0.49 42 1 h 29 min 1 h 58 min
Minimum iron40°C1)2.5 kg 0.44 49 1 h 05 min 1 h 20 min
Delicates30°C 1.0 kg 0.33 65 49 min 59 min
Automatic40°C 2.5 kg 0.30 - 0.60 30 - 50 1 h 00 min 1 h 15 min
Express40°C 2.5 kg 0.30 30 - 32 min
Woollens/30°C 2.0 kg 0.22 35 - 39 min
Silks/30°C 1.0 kg 0.24 39 - 36 min
Drying
CottonsNormal2)2.5 kg 1.30 11 - 1 h 12 min
Minimum ironNormal2)1.25 kg 0.65 5 - 37 min
Washing and Drying in a continuous sequence
Cottons60°C
Normal3)5.0 kg 3.40 65 - 4 h 30 min
Cottons60°C
Normal2.5 kg 2.30 45 - 3 h 00 min
Note for test institutes:
1)EN 60456 test programme2)EN 61121 test programme3)EN 50229 test programme
Consumption data can vary from the nominal values given depending on water
pressure, water hardness, water inlet temperature, room temperature, type and
volume of load, fluctuations in the electricity supply and any extra options
selected.
Consumption data
71
 
						

							Height 850 mm
Width 595 mm
Depth 580 mm
Depth with door open 975 mm
Height for building under 820 mm
Width for building under 600 mm
Depth for building under 600 mm
Weight 101 kg
Maximum floor load 1600 Newton (approx. 160 kg)
Capacity - Washing
Capacity - Drying5.0 kg dry laundry
2.5 kg dry laundry
Voltage see data plate
Connected load see data plate
Fuse rating see data plate / plug
Consumption data see Consumption data
Water flow pressure minimum 100 kPa (1 bar)
Water flow pressure maximum 1000 kPa (10 bar)
Inlet hose length 1.60 m
Drain hose length 1.50 m
Connection cable length 1.60 m
Drain pump head max. 1.00 m
Drain pump length max. 5.00 m
Lamp for drum lighting Type G4 (5 watts/12 volts)
Test certificates awarded Radio / TV suppression, VDE
Technical data
72
 
						

							The Settings menu is used to alter the
machines electronics to suit
changing requirements.
Settings can be altered at any time.
To open theSettingsmenu
ASwitch on the machine. The main
menu will appear.
15:03
Select programme
BAfter a few seconds an additional line
will appear in the display.
15:03
Select programme
SettingsF...
CConfirm your selection by pressing
theOKbutton.
DThis will take you into theSettings
menu.
CBackA
LanguageF...
Time...H
EUse the–and+buttons to select the
setting you want and confirm your
selection by pressing theOKbutton.
Important:
If you do not make a selection in the
Settings menu and in its sub-menus
within approx. 20 seconds, the menu
display will revert to the main menu.
LanguageJ
The display can be set via the
Language sub-menu to appear in
one of several different languages.
The flag after the wordLanguageacts
as a guide to prevent a language which
will not be understood from being set.
A tick will appear beside the language
to show that it has been set.
^Select the language you want and
confirm your selection.
Settings menuJ
73
 
						

							Time of day
You first have to decide whether you
want the time to show in the display.
Then you have to select either a 24 hour
or 12 hour clock.
Then set the current time of day.
To select a 24 hour or 12 hour clock
^Use the–and+buttons to select the
clock option setting you want and
confirm your selection by pressing
theOKbutton.
The display for setting the time of day
will then appear.
To set the time of day
00:00
Set the time
^Set the hour with the–and+buttons
and confirm your setting by pressing
theOKbutton. Now set the minutes.
The display will return to theSettings
menu.
The time of day can also be set by
pressing thembutton before
selecting a programme.
Water plus
This setting is used to select the
water intake setting for theWater plus
extra option.
There are three different options:
Water +
(the machine is delivered with
this option selected)
The water intake is increased in the
wash and rinse stages of the
programmes.
Extra rinse
An extra rinse is introduced in the
CottonsandMinimum ironprogrammes.
Water + and Extra rinse
^The water intake is increased in the
wash and rinse stages and an
additional rinse is also introduced in
theCottonsandMinimum iron
programmes.
A tick will appear beside the option to
show that it has been set.
Settings menuJ
74
 
						

							Gentle action
Activating gentle action reduces the
drum action and is suitable for
washing slightly soiled items more
gently. It should be activated for
garments with a single bar under the
care label and for articles which feel
too hard after they have been dried.
Gentle action can be activated for the
Cottonsand theMinimum iron
programmes.
If Gentle action has been activated the
wash rhythm will be gentle in all Cottons
and Minimum iron programmes.
The machine is delivered with the
Gentle action setting deactivated.
A tick will appear beside the option to
show that it has been set.
Suds cooling
When this is activated, additional
water flows into the drum at the end
of the main wash to cool the suds
down. Hot suds can damage plastic
drainage pipes.
Suds cooling takes place when a
Cottons 95-75°Cprogramme is
selected.
Suds cooling should be activated:
–
to prevent the danger of scalding if
the drain hose is hooked over the
edge of a sink or basin.
–
where the drainage pipes do not
comply with DIN 1986.The machine is delivered with Suds
cooling deactivated.
A tick will appear beside the option to
show that it has been set.
Door release
When this setting is activated the
drum door can be opened during a
drying programme at temperatures
up to 70°C.
If the Door release setting is
deactivated, the door can only be
opened at temperatures up to 55°C.
,Warning: High temperatures
can cause burning or scalding.
The machine is delivered with this
setting activated.
A tick will appear beside the option to
show that it has been set.
^Select the option you want and
confirm your selection.
Settings menuJ
75
 
						

							Distribution controller
The maximum final spin speed is
limited to prevent the laundry sticking
to the drum. (This setting is only
available when washing and drying in
a continuous sequence).
There are 4 different options:
1200 rpm (factory default setting)
1100 rpm
1000 rpm
900 rpm.
A tick will appear beside the option to
show that it has been set.
Alter time
The machine is designed to dry
effectively using as little energy as
possible. However, it ispossible to
lengthen or shorten the drying time
by up to 4 minutes.
The machine is delivered with the
drying time on setting 3 (= 0 minutes).
Settings menuJ
76
 
						

							Lock
The system lock prevents your
machine being used without your
knowledge.
When the system lock has been
activated, you have to enter a code after
switching the machine on. Otherwise
the machine cannot be operated.
To activate the lock
CBackA
XActivate
^SelectActivateand confirm your
selection.
^The display will now request that a
code is entered. The code is125and
cannot be altered.
To enter the lock code
The code is:125
0__
Enter code
^
Use the+button to enter the first
number. Confirm your selection of this
number by pressing theOKbutton.
Now set the second number.
^
Repeat the process until all three
numbers have been entered.^After the last number has been
entered, press theOKbutton.
Yes125No
Confirm code
^Confirm the code with theOKbutton
or if you want to correct a mistake,
press the–button.
^The lock will now be activated when
the machine is switched off.
To unlock the washer-dryer
When the machine is switched on
again, the display will request the lock
code.
^Enter lock code 125 as described
above and confirm the entry.
W
Entry OK
Lock deactivated
The machine is now unlocked.
To deactivate the lock
Proceed as for activating the lock.
Settings menuJ
77
 
						

							Temperature
You can choose for the temperature
to be displayed as°C/Celsiusor
°F/Fahrenheit.
A tick will appear beside the option to
show that it has been set.
^Select the option you want and
confirm your selection.
Buzzer
When the buzzer function has been
activated, an audible tone sounds at
the end of a programme or when
Rinse hold is reached.
There are two volumes.
Normal
(the machine is delivered with
this option selected)
The buzzer sounds at the end of a
programme or when Rinse hold is
reached.
Loud
The buzzer sounds at maximum volume
at the end of a programme or when
Rinse hold is reached.
A tick will appear beside the option to
show that it has been set.
^
Select the option you want and
confirm your selection.
Keypad tones
An audible tone sounds each time a
button is pressed.
The machine is delivered with the
keypad tone switched off.
A tick will appear beside the option to
show that it has been set.
Display contrast
There are ten different display
contrast settings.
The machine is delivered with the
display contrast on setting 5.
The display contrast will change as
soon as a different setting is chosen.
^Set the display contrast you require.
Display brightness
There are ten different display
brightness settings.
The machine is delivered with the
display brightness on setting 5.
The display brightness will change as
soon as a different setting is chosen.
^
Set the display brightness you
require.
Settings menuJ
78
 
						

							Standby
To save energy, the display goes out
after 10 minutes and the indicator
light for theStart/Stopbutton will start
flashing slowly.
There are two options:
On
Standby is activated:
–if a programme is not selected after
the machine has been switched on.
–after a programme has started.
– at the end of a programme.
Not in current Prog.
(the machine is
delivered with this option selected)
Standby is activated:
– if a programme is not selected after
the machine has been switched on.
– at the end of a programme.
Pressing one of the buttons switches
the display back on again.
A tick will appear beside the option to
show that it has been set.
Memory
If an extra option has been selected
for a programme, or the
recommended spin speed has been
altered, the machine will store the
changes in memory at the start of a
programme.
When this programme is chosen again
these settings will appear in the display.
The machine is delivered with the
memory function deactivated.
A tick will appear beside the option to
show that it has been set.
Set extended cool-down
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.
The cooling down phase can be
lengthened from 0 min (standard
cooling down phase = default setting)
to 18 minutes.
The programme duration will increase
accordingly.
To close the Settings menu
CBackA
LanguageF
Time...H
^
SelectBackand confirm your
selection.
Settings menuJ
79
 
						

							Alteration rights reserved/2208M.-Nr. 06 533 680 / 02