Miele W 2839 User Manual

Fitting a door front panel made
by another manufacturer
Preparing the front panel
Measure distanceXfor drilling the
hinge holes.
–with spacer bars:
– without spacer bars:
(the front panel must be
correspondingly higher)Mark the two hinge holes and the
four smaller holes as shown in the
diagram.Depending on country this machine
is supplied either left or right hand
hinged.
For left hand hinging only:
–front panel shown decor side face
down, upper edge at the bottom:
if width (b) increases, measurementa...

For right hand hinging only
–front panel shown decor side face
down, upper edge at the bottom:
if width (b) increases, measurementa
must also be increased
b= 592 mma= 21.5 mm
b= 593 mma= 22.0 mm
b= 594 mma= 22.5 mm
b= 595 mma= 23.0 mm
b= 596 mma= 23.5 mm
The heightHof the door front panel
corresponds to the door height of the
adjacent units.
Drill the two hinge holes (35 mm/
15.5 mm deep) in the back of the
front panel.
Next, drill the four smaller holes
(7 mm/10 mm deep) in the back of
the front...

Fitting a plinth facing
The gap between the lower edge of the
washing machine plinth and the floor
can be closed up using a suitable
kitchen furniture plinth facing.
The washing machine plinth has a
special groove in which a plinth facing
can be fitted.
Plinth facing dimensions
Length
: 592 - 596 mm
Thickness
:8mm
Height (
H): The plinth facing height
must be calculated after aligning the
height of the machine with the screw
feet or after fitting the raising kit(s).Installation
Calculate height (H) from...

The Miele water protection
system
The Miele water protection system
protects the washing machine from
water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
1) Inlet hose
– The inlet hose can withstand
pressure of more than 14,000 kPa
– The inlet hose has a protective
sleeve which is made from metal to
protect the hose from damage.
2) Electronic unit and washing
machine housing
–
Sump
Any leaking water is...

Connection to the water
supply
The machine should be connected to a
mains water supply in accordance with
local and national safety regulations.
The German authorities do not require it
to have a non-return valve as the
washing machine has been designed
to comply with DIN regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1,000 kPa. If it is higher
than 1,000 kPa it is essential to fit a
reducer valve.
Connection to the mains water supply
should incorporate a...

Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department or
your Miele dealer.
* For a delivery head of more than 1 m
(up to a...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply.
Please ensure the connection data
quoted on the data plate match the
household mains...

Load Consumption data
Energy Water Duration
in kWh in litres Short Normal
Cottons95°C 5.0 kg 1.70 42 2 h 09 min
60°C1)5.0 kg 0.85 42 1 h 49 min
60°C 2.5 kg 0.70 36 1 h 26 min
40°C1)5.0 kg 0.52 52 2 h 04 min
40°C2)2.5 kg 0.36 36 1 h 26 min
Minimum iron40°C1)2.5 kg 0.44 49 59 min 1 h 19 min
Delicates30°C 1.0 kg 0.33 69 49 min 59 min
Woollens30°C 2.0 kg 0.22 35 – 39 min
Automatic40°C 3.5 kg 0.35 - 0.50 40-55 – 1 h 18 min
Shirts60°C 1.5 kg 0.90 52 1 h 02 min 1 h 12 min
Express40°C 2.5 kg 0.30 30 – 30 Min....

Height 820 mm
Width 595 mm
Depth without lid 575 mm
Depth with door open 1180 mm
Weight 94 kg
Capacity 5 kg dry laundry
Voltage see data plate
Connected load see data plate
Fuse rating see data plate / plug
Consumption data see "Consumption data"
Water flow pressure minimum 100 kPa (1 bar)
Water flow pressure maximum 1.000 kPa (10 bar)
Inlet hose length 1.60 m
Drain hose length 1.50 m
Mains connection cable length 1.60 m
Delivery head max. 1.00 m
Maximum drainage length 5.00 m
LEDs Class 1
Test...

Settings menu
for changing default settings
The Settings menu can be used to alter the machine's electronics to suit
changing requirements.
Settings can be altered at any time.