Home > Miele > Washing Machine > Miele W 2839 User Manual

Miele W 2839 User Manual

Here you can view all the pages of manual Miele W 2839 User Manual. The Miele manuals for Washing Machine are available online for free. You can easily download all the documents as PDF.

Page 51

In the event of any faults which you
cannot remedy yourself, please
contact:
–your Miele Dealer or
–Miele (see back cover for contact
details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your machine, both of which
are shown on the data plate visible
above the porthole glass when the door
is open.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as
described in these instructions.Future updates (PC)
The indicator...

Page 52

Front view
Flexible stainless steel braided inlet
pressure hose
Electricity supply cable
Drain hose with flexible / detachable
swivel elbow
Control panel
Detergent dispenser drawerAdapter strip
Drum door
	Access to drain filter and the pump

Access panel to the emergency door
release and drainage
Four height adjustable screw feet
Installation and connection
52 

Page 53

Rear view
Electricity supply cable
Transit bar coversInlet hose (with flexible, waterproof
metallic outer sleeve)
Drain hose
Installation and connection
53 

Page 54

Installation surface
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
 The machine must be level and
securely positioned.
 To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
 We recommend the use of a plywood
base (at least 59x52x3cm). The base...

Page 55

Using the spanner supplied turn the
left-hand transit bar 90°, then

withdraw the transit bar.Turn the right-hand transit bar 90°,
then

withdraw the transit bar.
Installation and connection
55 

Page 56

To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
Fit the covers onto the two holes.
Then plug the holes as shown with
the caps.The washing machine must not
be moved without the transit bars in
place.
Store them in a safe place for future
use. They must be re-fitted if the
machine is to be moved again (e.g.
when moving house).
Re-fitting the transit bars
Re-fitting is carried out by reversing the
procedure.
Installation and connection
56 

Page 57

Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.
Using the spanner supplied turn
counter nut2in a clockwise
direction. Then turn counter nut2
together with foot1to unscrew.Use a spirit level to check the
machine is standing level.
Hold foot1securely with a pipe
wrench. Turn counter...

Page 58

Building under a continous
worktop / in a kitchen run
N= Niche height (820 - 930 mm)
This machine is specially designed for
installation under a continuous worktop
run in a fitted kitchen.
It is supplied with a cover plate,
instead of a lid, which is necessary
to ensure electrical safety and must
not be removed.
The washing machine must not be
used without the front panel in
place.–The slides* can be used to protect
the floor from damage when the
machine is pushed into position or
taken out for...

Page 59

Matching the fascia panel to
the height of adjacent drawer
fronts
Spacer bars
The fascia panel can be aligned with
the drawer fronts by adjusting the
spacer bars.
Using a socket spanner, turn
clockwise or anti-clockwise until the
required height is reached.
If necessary individual bars can be
removed or more added.

To do this, use the socket spanner to
loosen the nuts.
An adapter kit with spacer bars and
longer screws can be ordered as an
optional accessory. This can be used to
add spacer bars from...

Page 60

Fitting the front panel
The machine front can be fitted with a
door panel to match other kitchen units.
If fitted in a Miele kitchen, the door
panel can be ordered pre-drilled with
the necessary fixing holes as an
optional accessory.
If fitted in a non-Miele kitchen, a
suitable panel will have to be drilled
to suit by a qualified kitchen fitter.
See "Fitting a door front panel made
by another manufacturer" for details
on preparing and drilling the fixing
holes.
Front panel dimensions
Width
: 592...
Start reading Miele W 2839 User Manual

Related Manuals for Miele W 2839 User Manual

All Miele manuals