Miele W 2839 I Wpm Re Operating Instructions

Front view
Flexible stainless steel braided inlet
pressure hose
Electricity supply cable
Drain hose with flexible / detachable
swivel elbow
Control panel
Detergent dispenser drawerAdapter strip
Drum door
	Access to drain filter and the pump

Access panel to the emergency door
release and drainage
Four height adjustable screw feet
Installation
51
 

Rear view
Electricity supply cable
Transit bar coversInlet hose (with flexible, waterproof
metallic outer sleeve)
Drain hose
Installation
52
 

Installation surface
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
Please note the following points:
The machine must be level and
securely positioned.
To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
We recommend the use of a plywood
base (at least 59x52x3cm). The base
should...

Using the spanner supplied turn the
left-hand transit bar 90°, then

withdraw the transit bar.Turn the right-hand transit bar 90°,
then

withdraw the transit bar.
Installation
54
 

To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
Fit the covers onto the two holes.
Then plug the holes as shown with
the caps.The washing machine must not
be moved without the transit bars in
place.
Store them in a safe place for future
use. They must be re-fitted if the
machine is to be moved again (e.g.
when moving house).
Re-fitting the transit bars
Re-fitting is carried out by reversing the
procedure.
Installation
55
 

Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.
Using the spanner supplied turn
counter nut2in a clockwise
direction. Then turn counter nut2
together with foot1to unscrew.Use a spirit level to check the
machine is standing level.
Hold foot1securely with a pipe
wrench. Turn counter...

Building under a continous
worktop / in a kitchen run
N= Niche height (820 - 930 mm)
This machine is specially designed for
installation under a continuous worktop
run in a fitted kitchen.
It is supplied with a cover plate,
instead of a lid, which is necessary
to ensure electrical safety and must
not be removed.
The washing machine must not be
used without the front panel in
place.–The slides* can be used to protect
the floor from damage when the
machine is pushed into position or
taken out for...

Matching the fascia panel to
the height of adjacent drawer
fronts
Spacer bars
The fascia panel can be aligned with
the drawer fronts by adjusting the
spacer bars.
Using a socket spanner, turn
clockwise or anti-clockwise until the
required height is reached.
If necessary individual bars can be
removed or more added.

To do this, use the socket spanner to
loosen the nuts.
An adapter kit with spacer bars and
longer screws can be ordered as an
optional accessory. This can be used to
add spacer bars from...

Fitting the front panel
The machine front can be fitted with a
door panel to match other kitchen units.
If fitted in a Miele kitchen, the door
panel can be ordered pre-drilled with
the necessary fixing holes as an
optional accessory.
If fitted in a non-Miele kitchen, a
suitable panel will have to be drilled
to suit by a qualified kitchen fitter.
See "Fitting a door front panel made
by another manufacturer" for details
on preparing and drilling the fixing
holes.
Front panel dimensions
Width
: 592...

Fitting a door front panel made
by another manufacturer
Preparing the front panel
Measure distanceXfor drilling the
hinge holes.
–with spacer bars:
– without spacer bars:
(the front panel must be
correspondingly higher)Mark the two hinge holes and the
four smaller holes as shown in the
diagram.
For left hand hinging only:
–front panel shown decor side face
down, upper edge at the bottom:
if width (b) increases, measurementa
must also be increased
b= 592 mma= 21.5 mm
b= 593 mma= 22.0 mm
b= 594 mma=...