Miele T 7944 C Manual

Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be extended by 5 or 10 minutes,
if required. This makes the garments
easier to handle.
The cooling down time can only be
extended for programmes with drying
levels.
Follow the steps (
,,...) to
programme and store in memory.
Before you begin, ensure that:
– The tumble dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-....

Standby
To save energy, the display and the
programme sequence/check lights
go out after 10 minutes and the
Start/Stopbutton starts flashing
slowly.
To come out of standby mode
Turn the programme selector or
press a button. Neither will have any
effect if a programme is running.
On
The standby function is activated and
the display and programme
sequence/check lights will go out after
10 minutes:
– if a programme is not selected after
the dryer has been switched on.
– after a programme has started.
They...

Before you begin, ensure that:
–The tumble dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until theStart/Stopbutton lights up
constantly...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton six
times.
– TheLow temperatureindicator light
will flash 8 times briefly.
Anumberto show which option is
selected will appear in the display
alternating with the letterP.
0On
IFactory...

Memory function
The electronics will memorise any
extra options selected for a
programme. The duration selected
for the Warm air or Cool air timed
drying programmes will also be
stored in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
Follow the steps (
,,...) to
programme and store in memory.
Before you begin, ensure that:
– The tumble dryer is switched off.
– The door is...

Clean out airways indicator
Fluff should be removed after drying.
TheClean out airwaysindicator will
remind you to clean the filters when a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.
You will have an idea of how often this
should be done after a few drying
programmes.
Follow the steps (
,,...) to
programme and store in memory.
Before you begin, ensure that:
– The tumble dryer is switched off.
– The door is closed.

Press...

Keypad tone
An audible tone sounds each time a
button is pressed.
Follow the steps (
,,...) to
programme and store in memory.
Before you begin, ensure that:
–The tumble dryer is switched off.
–The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst carrying out steps
-.
Switch the dryer on.
Wait until theStart/Stopbutton lights up
constantly...
. . . and then release theStart/Stop
button.
Press theLow temperaturebutton
nine times.
– TheLow temperatureindicator light
will flash...

Adjusting the dryers
electronics for very soft water
In some areas of the UK, water is
extremely soft which can affect the
sensitivity of the control electronics.
If the dryer is installed in an area of
very soft water, you should contact
your local water supplier for
information and advice regarding
water hardness and water
conductivity. If the water
conductivity is less than 150 µS, the
following programmable function will
need to be activated.
Important. This programmable function
should not be...

Extending the range of the
drying levels
You can extend the range of the
drying levels for many of the
programmes:
Machine iron+
(drier than Machine iron).
Slightly dry
(drier than Hand iron).
Normal+
(drier than Normal).
This programmable function is only
available for programmes with drying
levels.
Follow the steps (
,,...) to
programme and store in memory.
Before you begin, ensure that:
– The tumble dryer is switched off.
– The door is closed.

Press theStart/Stopbutton and keep
it pressed in whilst...

59 

M.-Nr. 07 851 060 / 02Alteration rights reserved/3611