Miele T 7944 C Manual

Problem Possible cause Remedy
TheStart/Stopbutton is
flashing slowly and the
display is dark.The dryer is in Standby
mode.
This is quite normal and
not indicative of any fault.See Programmable
functions.
Sometimes a
programme cannot be
started and the
corresponding
programme indicator
light does not light up.No obvious cause.
–Switch the dryer off
and back on again.
–Select one of the
programmes that
would not start.
–If it still will not start,
there is a fault. Contact
the Miele Service
Department....

An unsatisfactory drying result
Problem Possible cause Remedy
The laundry is not
sufficiently dry.The load consisted of
different fabrics.–Finish drying using the
Warm airprogramme.
–Select a different
programme next time *.
Items made of synthetic
fibres are charged with
static electricity after
drying.Synthetic fibres tend to
attract static charge.Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
programme or a fabric
conditioner sheet to the
load when...

Other problems
Problem Possible cause Remedy
The drying process
goes on too long or
even switches off.In some circumstances, the
Clean out airwaysindicator
light still comes on, even
though the filters are clean.Please check all the
possible causes and
switch the dryer off and
then back on again.
Ventilation to and from the
dryer may be insufficient,
e.g. because it is installed in
a room which is too small.
This can cause the
temperature in the room to
rise sharply.Open a door or window
while the dryer...

Problem Possible cause Remedy
Water leaks from the
dryer after the
condenser unit has
been cleaned.–The inner cover of the
condenser unit has not
been locked properly
and/or the condenser
unit has not been
positioned correctly.
–Fluff has collected in
the condenser unit
housing.–Ensure that the
condenser unit is
positioned correctly
and lock the inner
cover.
–Check the rubber
seals.
–Use a cloth to remove
any visible fluff from the
inside of the condenser
unit housing.
The programme does
not start.No...

Changing the lamp
Disconnect the tumble dryer from
the mains electricity supply.
Open the door.
You will find the interior lamp cover at
the top of the drum aperture.
Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.

Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele Dealer
or the...

Repairs
In the event of any faults which you
cannot remedy yourself, please contact
–your Miele dealer or
–the Miele Service Department (see
back cover for contact details).
When contacting your dealer or the
Service Department, please quote the
model and serial number of your
appliance, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.
N.B. A call-out charge will be
applied for service visits where the
problem could have been resolved
as described in...

Front view
Mains connection cable
Control panel
Condensed water container
Door
Service panel for condenser unitFour height adjustable screw feet
Air inlet and outlet vent for cooling
the condenser unit
	External drainage options (e.g. via
wash basin, wash basin drain outlet
or gully)
Installation and connection
37 

Rear view
Protruding lid for holding when
moving the machine (see arrows)
Air inlet vent for cooling the
condenser unit
Mains connection cable
External drainage of the condensed
water
Accessories for connection to a sink
drain outlet
Installation site
The machine lid must not be
removed.
The dryer can be pushed under a
worktop with its lid in place, providing
the worktop is high enough.
Make sure the dryer door can be
opened without hindrance after
installation.
Transporting the machine to its...

Levelling the machine
The machine must be perfectly level to
ensure safe and proper operation.

The screw feet can be adjusted to
compensate for any unevenness in
the floor.
The air inlet and outlet vents on
the front and back of the machine
must not be covered as this would
prevent sufficient ventilation for
cooling the condenser unit.
Do not block the gap between
the bottom of the tumble dryer and
the floor with plinth facings, deep file
carpet etc. This would hinder a
sufficient flow of air to the...

External condensed water
outlet
General notes
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose at
the back of the dryer. The condensed
water can also be drained off directly if
the tumble dryer is installed near a sink,
drain outlet etc. so that the condensed
water container does not have to be
emptied.
Drain hose length............1.50 m
Maximum delivery head.......1.50 m
Maximum drain hose length....4.00 m
If the on-site water drainage...