Miele Kwt4154ug1 Manual

							Door seal
Do not use any oils or grease on the
door seal as these will cause the
seal to deteriorate and become
porous over time.
The door seal should be cleaned
regularly with clean water, then wiped
dry with a soft cloth.
Active charcoal filter
Replace the active charcoal filters with
new ones once a year. These are
available from Miele.
^
Turn the filters 90° clockwise or
counter-clockwise.
^
Remove the filters.
^
Insert the new filters with the handle
in the vertical position.
^
Turn the filters 90° clockwise or
counter-clockwise until they click into
position.
After cleaning
^Replace all shelves in the appliance.
^Insert the plug in the power outlet
and turn the appliance back on.
Cleaning and care
21 
						

							Repairs should only be carried out
by a qualified and trained person in
strict accordance with local and
national safety regulations.
Unauthorized repairs could cause
personal injury or machine damage
and may void the warranty.
With the aid of the following guide
minor problems can be corrected
without a service call.
What to do if...
. . . the appliance does not get cool.
^Check whether the appliance has
been turned on. The temperature
display must be lit up.
^Check that the plug is correctly
inserted in the power outlet.
^Check that the fuse is not defective
and has not been tripped. Reset the
cicrcuit breaker.
. . . the appliance is kicking on too
frequently and for too long.
^
Check whether the ventilation slits
are covered or dusty.
^
The appliance door has been
opened too frequently.
^
Check that the door has been closed
properly.. . . the alarm sounds and the
temperature display flashes.
^Has the appliance door been open
for longer than 60 seconds?
If not, then the temperature is above or
below the set temperature. Possible
reasons:
^The appliance door has been
opened too frequently.
^the ventilation slits are covered.
^there has been a lengthy interruption
to the power supply.
Once the problem has been resolved
the temperature display will light up
continuously, and the alarm will stop.
...abarislituporflashing in the
temperature display.
Only temperatures within the range that
the appliance can display will be
shown. If the temperature is not within
this range, a bar will be displayed
instead.
...F0orF1 appears in the
temperature display.
There is a fault. Contat MieleCare.
. . . you cannot turn the appliance off.
The safety lock has been activated.
Problem-solving guide
22 
						

							. . . the interior light is not working.
Contact MieleCare.
If, after following these suggestions,
you still cannot remedy the fault,
please contact MieleCare.
To prevent unnecessary loss of
temperature it is advisable not to
open the door while waiting for the
appliance to be serviced.
Problem-solving guide
23 
						

							Normal noises What causes them?
Brrrrr...Humming noise made by the motor (compressor). This noise
may get louder for brief periods, whenever the motor kicks in.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds occur whenever the thermostat switches the
motor on or off.
Sssrrrrr....In multi-zone and frost-free appliances, the movement of air
circulating through the appliance can sometimes just barely be
heard.
Please bear in mind that a certain amount of noise is unavoidable (from the
compressor, and the coolant circulating through the system).
Noises that you can
easily rectifyWhat causes them, and what can you do about
them?
Rattling, vibratingThe appliance is uneven: Balance the appliance using a level,
and by raising or lowering the screw feet underneath the
appliance, or placing something underneath them.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets, or shelves are unstable or sticking:Check all
removable items and refit them correctly.
Bottles or containers are unstable or knocking against each
other: Separate them.
The transport cable clips are hanging loose at the back of the
appliance: Remove the clips.
Noises
24 
						

							In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department at
the address on the back of this booklet.
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance
given on the data plate inside the
appliance.
After sales service
25 
						

							26 
						

							Installation instructions
To prevent accidents
and machine damage
read these instructions
before
installation or use. 
						

							,Avoid the risk of electrical shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer will
not be held responsible for damage
or injury arising from unauthorized
work.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
V1-800-565-6435The appliance comes with a UL-listed,
3-wire power supply cord.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licensed electrician only.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance. Ideally, the power outlet
should be next to the appliance and
easily accessible. Do not connect the
appliance to the power supply by an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (danger of overheating).
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
Electrical connection
28 
						

							This appliance must be built in;
otherwise it could tip over.
To ensure that the appliance
functions correctly in tropical
climates where the ambient
temperature exceeds 38°C and air
humidity levels exceed 70%, the
appliance MUST be used in a
climate-controlled room.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
The appliance should not be installed
where it will be exposed to direct
sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+18°C to +38°C
+18°C to +43°C
+10°C to +38°C
+10°C to +43°C
If the appliance is used in a room that is
too cold, the cooling system will switch
off for too long, causing the internal
temperature in the appliance to rise,
with the risk of affecting the wine stored
there.
Ventilation
The air at the back of the appliance
gets warm. The appliance housing unit
must be constructed to allow sufficient
space for ventilation.
The air intake and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installation
^
Before building in, remove all
accessories from the appliance.
^
Remove any cable clips from the rear
of the appliance.
^
Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrances.
Installation
29 
						

							The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
^Close the door, and unscrew the top
hinge pin from the doora.
^Unscrew the door staybfrom
underneath the door.
^Tip the door forward slightlyc, and
lift it up and offd.^Unscrew the top hinge platee, turn
it around, and refit it on the opposite
side.
^Unscrew the lower hinge platef.
^Remove the hinge ping, and
replace it in the hinge plate from
underneath. Ensure that the spacer
on which the hinge pin sits is
correctly positioned.
^Turn the hinge plate around, and refit
it on the opposite side.
Changing the door hinging
30