Miele Kfn 9758 Id Operating And Installation Instructions

^Unscrew ball jointbusing a
spanner, and remove soft-close
mechanismctogether with the ball
joint.
Do not separate the soft-close
mechanism from the ball joint. This
would damage the mechanism.
^
Stand the appliance doors up one by
one, and slacken the hinges at the
front (the hinges remain open).
^
Remove capsafrom the top and
bottom of each door (if the caps are
not in place, they will have been
supplied separately with the
appliance).
^
Remove screwsbfrom all of the
hinges, and refit each hinge in...

^Hang the doors onto the pre-fitted
screws, and push the doors inwards.
^Tighten the screws at the top, middle
and bottom securely.
^Replace coversa,bandc.
^Then replace capsdin the vacant
holes.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
52
 

All fitting instructions given are for a
right hand hingedappliance. If you
have converted the appliance to left
hand hinging you will need to adapt
these instructions accordingly.
To install the appliance you will need
the following:
–a cross-slotted screwdriver,
–a selection of Torx screwdrivers,
–a hexagon spanner.
Weight of the furniture doors
Before fitting furniture doors, ensure
that the weight of the door does not
exceed the maximum permitted:
Appliancemax.
weight
of upper
door in
kgmax.
weight...

Preparing the appliance
^Slide cover stripainto the holder as
shown, with the bumps facing
downwards. The bumps will fit into
keyhole slotsb.
^Position the mains electricity cable so
that the appliance can be connected
easily once installed.
^
Secure fixing bracketsc(supplied)
to the appliance doors using a
hexagon screwdin the pre-drilled
holes.
(With large furniture doors, attach a
third pair of fixing bracketscin the
handle region of the doors).^Push the appliance three-quarters of
the way into its...

^Open both appliance doors.
^Secure plastic bracketgto the side
opposite the hinges using screwsh
(M5 x 22)
^
Attach fixing bracketiloosely to the
appliance using screwsj(M5 x 15).
^
If necessary shorten sealing stripk
to the height of the niche and then
remove the protective foil.
^
Apply sealing stripkto the side of
the appliance on which the doors are
opened so that it is flush with the
front edge of the appliance.
Sealing stripkshould meet up with
the lower edge of fixing bracketi.Building in the...

This gap must also be maintained in
housing units where the floor or base
shelf is set-back from the front of the
unit, even if it means that plastic
bracketdprotrudes over the edge of
the housing unit floor.
On furniture with fittings such as buffer
strips or seals:
^Pull the appliance forwards by
dimensionh(this is the depth of the
buffer strip or seal) in order to keep
the gap at42 mmall round.
The hinges now protrude by dimension
hand plastic bracketdis aligned
parallel with the front edge of the...

^Screwa4x19mmscrewcthrough
fixing bracketd
^Push the bracket towards the
housing unit side wall and tighten
screwse(M5 x 15) .
^
Close bracketf.
^
Close the appliance doors.
Fitting the furniture doors
^A gap of 8 mmamust be set
between the appliance door and the
fixing bracket.
^Push fitting aidsbup to the height of
the furniture door: the lower edge X
of the fitting aids must be at the same
height as the upper edge of the
furniture door being fitted (see-on
the diagram).
^
Undo nutscand take fixing...

^Using a pencil, lightly mark a line
down the centre of the inside of the
furniture door.
^Hang fixing bracketdwith the fitting
aids onto theinsideof the furniture
door. Align the fixing bracket
centrally.
^
Attach the fixing bracket securely
using at least 6 screwse. (On
cassette doors only use 4 screws on
the edges).
^
Pull the fitting aids upwards to
remove themf.
^
Turn them around and fit them into
the middle slots on fixing bracketg
for safe keeping.^Hang the furniture door onto
adjusting boltsh....

Securing the appliance doors to the
furniture doors:
^Drill pilot holesaand screw in the 4
x 14 mm screwsb.
Make sure the two metal edges are
alligned (SymbolII).
– Align depth Z on the furniture door:
Loosen screwscat the top of the
appliance door, and loosen the
hexagon-headed screwdat the
bottom of the fixing bracket. By
moving the furniture doors, create a
gap of 2 mm between the furniture
doors and the front edge of the
housing unit.^Close both of the doors, and align
them with the neighbouring...

^Replace upper coverk, and snap it
into place.
^Replace side coversl, making sure
they snap into place.
^Replace side coversm, making sure
they snap into place.To make sure the appliance is
correctly fitted:
–The doors must close properly.
–The doors must not touch the
housing unit.
–The seals at the top edge of the
handle side must fit properly.
^To double check place a torch in the
appliance and close the doors. Turn
the lights out in the room. If you can
see any light shining out from the
sides double...