Miele Kfn 9758 Id Operating And Installation Instructions

. . . the Super freeze indicator light
does not light up, even though the
appliance is working.
The indicator light is defective. Call the
Service Department.
. . . you cannot switch the appliance
off.
The safety lock has been activated.
...nA appears in the freezer
section temperature display.
The freezer section temperature has
risen too high at some point during the
last couple of days because of a power
cut.
^Press the alarm off button whilst nA
is lit up in the display.
The temperature display will...

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Remember that the noise of the...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer or Chartered Agent
or
–the Miele Service Department
(see back cover for contact details).
When contacting your Dealer/Chartered
Agent or Miele, please quote the model
and serial number of your appliance.
This information is given on the data
plate inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
Guarantee
For...

All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra...

All electrical work should be carried out
by a suitably qualified and competent
person in accordance with local and
national safety regulations.
The appliance is supplied with a mains
cable and moulded plug ready for
connection to 220-240 V 50 Hz supply.
The voltage and frequency are given on
the data plate. Please ensure that these
match the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to install a residual...

To avoid a hazard due to instability
of the appliance, it must beinstalled
in accordance withthese
instructions.
Location
The appliance should be installed in a
dry, well ventilated room. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance...

Before installation
^Before installation, remove the cover
strip, sealing strip and other
accessories from the appliance and
from the external rear wall of the
appliance.
^On no account should the spacers
be removed from the back of the
appliance. These ensure the gap
required between the back of the
appliance and the wall is maintained.
^Remove any cable clips from the rear
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
Does your old...

Freezer section height Niche height
AB
KFN 9758 iD695 1772 - 1788
Building-in dimensions
48
 

The door hinges are set ex-works to
enable the doors to be opened wide.
However, if the opening angle of the
doors needs to be limited for any
reason, the hinges can be adjusted to
accommodate this.
–For example, if the appliance doors
hit an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance doors
to be cushioned so that...

Before installing the appliance, you will
need to decide on which side the door
is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging, you will
need various sizes ofTorx
screwdrivers,aslotted
screwdriverand aspanner.
^Open both appliance doors.
^
Remove coversa,bandcand
capsdwith a screwdriver.
^
Slightly loosen fixing screwseat the
top, middle and bottom of the
appliance.
^
Push each of the doors outwards and
take them off their hinges.^Unscrew...