Miele Kfn 9755 Ide Operating And Installation Instructions

. . . the compressor runs
continuously.
To save energy, the compressor runs at
a lower speed, but for longer, when
less cooling is required. In this case,
the motor runs for longer.
. . . the frozen food is thawing
because the freezer section is too
warm.
^Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
If so, increase the temperature of the
room.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the...

...nA appears in the freezer
section temperature display.
The freezer section temperature has
risen too high at some point during the
last couple of days because of a power
cut.
^Press the alarm off button whilst nA
is lit up in the display.
The temperature display will show the
warmest temperature recorded in the
freezer section during the power cut.
Depending on the temperature
displayed, you should check the
condition of food in the freezer section.
If it has defrosted or started to defrost,
check...

. . . the interior lighting in the
refrigerator is not working.
Has the appliance door been left open
for too long? The lighting switches itself
off automatically after approx. 15
minutes if the door is left open.
If it also does not come on when the
door is opened briefly, but the
temperature display is working, then
the lighting is defective.
^Call the Service Department.
The LED lighting may only be repaired
or replaced by a service technician.
There are live electrical components
under the cover....

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Notes on connecting to the
mains water supply
Connection to the mains water
supply should only be carried out by
a qualified and competent person in
accordance with national and local
regulations.
The water quality must conform to
the requirements for drinking water
in the country the appliance is being
installed in.
– This appliance complies with IEC
61770 and EN 61770 (ATS 5200.101
in Australia).
– All items used for connecting the
appliance to the mains water supply
must comply with the current...

^The stainless steel hose should be
attached to the solenoid valve at the
base of the appliance at the back.
^Ensure that the hose is fitted correctly
and that it is water tight.
^Turn on the stopcock slowly and
check the whole water system for
leaks.
^The appliance can then be
connected to the electricity supply.
^Push the appliance into its final
position.
When doing so, make sure that the
stainless steel hose is not kinked or
damaged.
After a maximum of 24 hours the first
ice cubes will drop out of...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

This appliance must be built in,
otherwise it could tip up.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical /...

The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
Before installing the appliance
^Before installation remove the cover
strip, sealing strip and other
accessories from inside the appliance
and from the external rear wall of the
appliance.
^Do not remove the spacers from the
back of the appliance. These ensure
the gap required between the back
of the appliance and the wall is
maintained.
^
Remove any cable clips from the
back of the appliance.^Remove...