Miele Kfn 12823 Sded Operating And Installation Instructions

							~Do not use defrosting sprays or
de-icers, as they might contain
substances which could damage the
plastic parts or which could cause the
build-up of gases and pose a danger to
health.
~Do not use any oils or grease on the
door seals, as these will cause the
seals to deteriorate and become
porous with time.
~Do not store cooking oil in the
refrigerator door. Traces of oil can
cause stress cracks to occur in the
plastic components in the door.
~Do not block the ventilation gaps in
the appliance as this would impair the
efficiency of the appliance, increase the
electricity consumption and could
cause damage to the appliance.
~The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range
for your appliance is stated on the data
plate inside the appliance.
Installing it in a room with too low an
ambient temperature, e.g. a garage,
can lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
~Do not use a steam-cleaning
appliance to defrost or clean this
appliance. Steam could reach the
electrical components and cause a
short circuit.
Disposal of your old appliance
~Before disposing of an old
appliance, first make the door latch or
lock unusable.
This way you will prevent children from
accidentally locking themselves in and
endangering their lives.
~Be careful not to damage any part of
the pipework whilst awaiting disposal,
e.g. by
–puncturing the refrigerant channels
in the evaporator.
–bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Warning and Safety instructions
11
 
						

							Normal energy
consumptionIncreased energy
consumption
Installation siteIn a ventilated room. In an enclosed, unventilated room.
Protected from direct sunlight. In direct sunlight.
Not situated near to a heat source
(radiator, oven).Situated near to a heat source
(radiator, oven).
Where the ideal ambient room
temperature is approx. 20°C.Where there is a high ambient
room temperature.
Temperature setting with
a thermostat which is
approximate
(set in stages).With a medium setting of 2 to 3. With a high setting: the lower the
temperature in the compartment,
the higher the energy
consumption.
Temperature setting with
a thermostat which is
exact to the degree
(digital display).Cellar section 8 to 12°C
On appliances with winter setting,
please make sure that the winter
setting is switched off when the
ambient temperature is warmer
than 16 °C. Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18°C
Wine storage section 10 to 12 °C
UseOnly open the doors when
necessary and for as short a time
as possible.Frequent opening of the doors for
long periods will cause a loss of
coldness.
Store food in an organised way. If food is not stored in an
organised way, searching for an
item will mean the door is open for
longer.
Allow hot food and drinks to cool
down before placing them in the
appliance.Placing hot food in the appliance
will cause the compressor to run
for a long time, as the appliance
will have to work harder to lower
the temperature.
Store food covered or packaged. The evaporation or condensation
of liquids will cause a loss of
coldness in the refrigerator.
Place frozen food in the
refrigerator to defrost.
Do not over-fill the appliance to
allow air to circulate.
DefrostingDefrost the freezer compartment
when a layer of ice 0.5 cm thick
has built up.A layer of ice hinders the cold
from reaching the frozen food, and
causes an increase in energy
consumption.
How to save energy
12
 
						

							Before using for the first time
The stainless steel trim to the interior
shelves and the door shelves has a
layer of protective foil to prevent
damage during transportation. Please
remove this carefully after installation.
^Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing-up liquid, and
then dry with a soft cloth.
^Carefully remove the protective foil
from the stainless steel trim.
Important:
To ensure the correct functioning of
the appliance, let it stand for
between 1½ and 2 hours after
transporting it to its final location
before connecting it to the mains.
Switching on
The refrigerator and freezer sections are
switched on together by pressing the
master switch on the right hand side of
the control panel, or by pressing the
On/Off button on the left hand side of the
control panel.
^
Press the master switch on the right
hand side of the control panel.
The temperature display for the
refrigerator section will show the
selected temperature setting. The
temperature display for the freezer and
the alarm indicator light will flash untilthe freezer section has cooled down to
the correct temperature for freezing.
The appliance will start cooling down
and the interior light in the refrigerator
section will come on if you open the
door.
Allow the appliance to run for a few
hours before placing food in it. This will
ensure that the temperature is
sufficiently low.
Cool pack
Place the cool pack in the top drawer of
the freezer. The cool pack will be at its
most effective after it has been in the
freezer for approx. 24 hours.
Switching off
^Press the master switch on the right
hand side of the control panel until
both temperature displays go out.
The interior light will not come on when
you open the door and the cooling
process will be switched off.
Switching on and off
13
 
						

							To switch the refrigerator section off
separately
The refrigerator section can be
switched off without having to switch off
the freezer section. This is useful e.g.
whilst on holiday.
^Press the master switch on the right
hand side of the control panel.
The temperature display will light up for
both the refrigerator and the freezer
sections.
^Press the On/Off button for the
refrigerator section on the left hand
side of the control panel until the
temperature display for the
refrigerator section goes out.
The refrigerator section is now switched
off.
The temperature display for the freezer
section will remain lit up.
To switch the refrigerator section on
again
^
Press the On/Off button on the left
hand side of the control panel again.
The refrigerator section temperature
display will light up. The refrigerator
section will start cooling. The interior
light will come on when the door is
opened.Switching off for longer
periods of time
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
^switch the appliance off,
^switch off at the wall socket and
withdraw the plug,
^clean the appliance out and
^leave the doors ajar to air it.
If, during a long absence, the
appliance is switched off but not
cleaned out and the doors are left
shut, there is a danger of mould and
odours building up inside the
appliance.
Switching on and off
14
 
						

							It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
The temperature in the appliance will
rise:
–the more often the door is opened
and the longer it is kept open,
– the more food that is stored in it,
– the warmer the food is which is being
put into it,
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
...intherefrigerator section
We recommend a temperature of5°C
in the middle of the refrigerator.
...inthefreezer section
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °Cis required. At this temperature
the growth of micro-organisms is
generally halted. As soon as the
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
Setting the temperature
The temperature is set in each zone by
using the respective temperature
button.
^
Press the temperature button
repeatedly until the indicator light for
the temperature you want lights up in
the display.
The temperature changes each time
you press the button.
The temperature being set will flash in
the display as you do this.
The correct temperature
15
 
						

							Temperature display
The temperature display on the
control panel always shows the
requiredtemperature.
Temperature range
The temperature can be adjusted:
–In the refrigerator section from 1 °C
to9°C
–In the freezer section from -15 °C to
-32 °C.
The ambient temperature in the room
and the installation location can affect
the time it takes for the appliance to
reach the lowest temperature. If the
ambient temperature is too high, the
appliance may not reach the lowest
temperature.Thetemperature display will flashif
–the temperature in the appliance is
not within the possible temperature
range,
–a different temperature is being set,
–the temperature in the appliance has
risen by several degrees, indicating
that the appliance is warming up too
much.
This loss of coldness is no cause for
concern in the following circumstances:
–when the door has been left open for
a while, e.g. for removing or storing a
large amount of food,
– when fresh food is being frozen.
However, if the temperature in the
freezer section remains above -18 °C
for a long time, check that the frozen
food has not started to defrost. If it has
started thawing, check that the food is
safe to use and if it is, use it as quickly
as possible.
The correct temperature
16
 
						

							Your appliance has been fitted with a
warning system which ensures that the
temperature in the freezer section
cannot rise unnoticed and to avoid
energy being wasted if a door is left
open.
Activating the alarm system
The alarm system is always active. It
does not have to be switched on
manually.
Temperature alarm
If thefreezer section temperature
becomes too warm, an alarm will sound
and the freezer section temperature
display and the alarm off indicator light
will flash.
The temperature the appliance is set at
determines the temperature the
appliance recognises as being too
warm.
The alarm will sound and the
temperature display and alarm off
indicator light will flash, for example,
–
if the freezer door has been left open
for a while, e.g. in order to load, to
re-arrange or to take food out.
–
when freezing large amounts of food
at once.
–
in the event of a power cut.
Once the set temperature has been
reached in the freezer section, the
alarm switches off and the temperature
display stops flashing and lights up
constantly.
Door alarm
The alarm will sound if a door is left
open for more than 60 seconds.
The alarm will stop as soon as the door
is closed.
Switching the alarm off early
If the noise disturbs you, you can
switch the alarm off early if you wish.
^Press the alarm off button.
The alarm will stop.
The temperature display and the
alarm off indicator light will continue
to flash until the set temperature has
been reached. They then stop
flashing and light up constantly. The
alarm system is now ready should it
be needed again.
Alarm
17
 
						

							Super freeze
Switch the Super freeze function on
before putting fresh food into the
freezer.
This helps food to freeze quickly and
retain its nutrients, vitamins, flavours
and appearance.
Super freeze is not necessary:
–when placing food in the freezer that
is already frozen.
–when freezing up to 2 kg fresh food
daily.
Switching on Super freeze
When freezing small quantities of food
in the freezer, the Super freeze function
should be switched on6 hours
beforehand. When freezingthe
maximum load of foodthe Super
freeze function should be switched on
24 hours beforehand.
^
Press the Super freeze button. The
Super freeze indicator light will come
on.
The appliance works at full power to
lower the temperature in the appliance.Switching off Super freeze
The Super freeze function will switch off
automatically after approx. 65 hours.
The indicator light will go out and the
appliance will run at normal power
again.
To save energy the Super freeze
function can be switched off once a
constanttemperature of -18°C or
colder has been reached in the freezer.
^Press the Super freeze button. The
Super freeze indicator light will go
out, and the appliance will continue
to operate at normal power.
Super freeze and Dynamic cooling
18
 
						

							Dynamic coolingm
When the Dynamic cooling function is
not switched on, the natural circulation
of air in the appliance will cause
different temperature zones in the
refrigerator as the cold, heavy air will
sink to the lowest section of the
appliance. You should bear this in mind
when placing food in the appliance
(see Using the refrigerator efficiently).
However, if you are placing a large
amount of food in the refrigerator at any
one time, it is a good idea to switch on
Dynamic cooling. This way you can
distribute the temperature inside the
appliance to all areas more evenly so
that all the food will be chilled to about
the same degree.
The temperature is set as normal with
the temperature control.
Dynamic cooling should also be
selected when:
– the ambient temperature in the room
is high (above approx. 30 °C), and
–
the room humidity level is high.
Switching on Dynamic cooling
^
Press the Dynamic cooling button.
The Dynamic cooling indicator light
will come on.Make sure the fan at the back of the
appliance is not restricted to ensure
unhindered air circulation.
Switching off Dynamic cooling
^Press the Dynamic cooling button
m. The Dynamic cooling indicator
light will go out.
The fan automatically switches off
when the door is open.
Super freeze and Dynamic cooling
19
 
						

							Different storage zones
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
This appliance has Dynamic
cooling, which helps to keep an
even temperature when the fan is
running. When Dynamic cooling is
switched on, the difference between
the various zones is less
pronounced.
Warmest area
The warmest area is in the top section
of the door. Use this for storing butter
and cheese.
Coldest area
The coldest area in a refrigerator is
directly above the vegetable
containers.
Use this for all delicate and highly
perishable food, e.g.
–
fish, meat, poultry,
–
sausage products, ready meals,
–
dishes or baked goods containing
eggs or cream,
–
fresh dough, cake mixtures, pizza or
quiche dough,
–
soft cheese and other dairy
products,–pre-packed vegetables and other
fresh food with a label stating it
should be kept at a temperature of
approx. 4 °C.
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
Do not store cooking oil in the
refrigerator door. Traces of oil can
cause stress cracks to occur in the
plastic components in the door.
Food must not touch the back wall of
the refrigerator, as it may freeze to
the back wall.
To allow air to circulate efficiently,
do not pack food too closely
together in the refrigerator. Do not
cover the fan in the rear wall of the
refrigerator, as this is essential for
keeping the appliance cool.
Using the refrigerator efficiently
20