Miele K855 Id1 Manual

Close the lower door.
Caution. The lower door is not
secure as soon as the middle hinge
plate is removed.
Pull the middle hinge pin\012upwards
to remove it.
Carefully lift the lower door off and
place it to one side.
Pull coveroff.
Unscrew hinge plate, rotate it by
180° and fit it on the opposite side.

Pull off plastic cap	, turn it through
180° and fit it back on to hinge plate
.

Refit coveron the opposite side.Remove cap\015from the bearing
bush in the door and refit on the
opposite...

Changing over the doors
Pull complete hinge pintogether
with discand adjustable foot
upwards and off.
Remove cover cap.
Undo screwsand take hinge plate
off.
Undo the screw of hinge part	on
hinge plateslightly. Fit it into the
hole opposite in hinge plateand
tighten up the screw.

Refit cover capin the other hole.

Remove coverand fit it into the
holes on the opposite side.Screw hinge plateinto position on
the opposite side using the twoouter
long slots only. To make it possible to
align...

Fit hinge pin\012into middle hinge
platein the lower door. The ridge
on the hinge pin will fit into the notch
in the hinge plate.
Then fit the upper door on middle
hinge pin\012.
Close the upper door.
Fit hinge plateonto the opposite
side and secure it with screws.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.Fit coversandto their opposite
sides.
Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the...

Refitting the handles
Please make sure you follow the
instructions below carefully when
you refit the handles. The door seal
will be damaged if the handle is
fitted incorrectly.
Loosely attach the handle to the
opposite side of the door with the two
front screws.
Mounting platemust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,

tighten both grub screwswith a
suitable allen key until mounting plate
lines up...

The appliance doors can be aligned
with the housing after they have been
fitted.
In the following illustration the door is
not shown in the closed position to
make it easier to see what you have
to do.
To align thelower dooruse the long
outer slots in the lower hinge plate:
Remove centre screwfrom the
hinge plate.

Slightly loosen both outer screws.

Align the door by sliding the hinge
plate to the left or right.

Then tighten screwsagain. Screw
does not need to be used again.To align theupper...

* The appliance depth is increased
by approx. 35 mm for appliances
with wall spacers fitted.
Top box
Appliance
Housing unit
WallThe appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300...

57 

58 

59
United Kingdom
Miele Co. Ltd.
Fairacres, Marcham Road
Abingdon, Oxon, OX14 1TW
Customer Contact Centre Tel: 0330 160 6600
E-mail: [email protected]
Internet: www.miele.co.uk
Australia
Miele Australia Pty. Ltd.
ABN 96 005 635 398
1 Gilbert Park Drive, Knoxfield, VIC 3180
Tel: 1300 464 353, Fax: (03) 9764 7149
Internet: www.miele.com.au
Miele (Shanghai) Trading Ltd.
1-3 Floor, No. 82 Shi Men Yi Road
Jing' an District
200040 Shanghai, PRC
Tel: +86 21 6157 3500, Fax: +86 21 6157 3511
E-mail:...

M.-Nr. 10 029 880 / 00en-GB KFN 11923 SD-2, KFN 11923 SD edt/cs-2