Miele K855 Id1 Manual
Have a look at the manual Miele K855 Id1 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 171 Miele manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Close the lower door. Caution. The lower door is not secure as soon as the middle hinge plate is removed. Pull the middle hinge pin\012upwards to remove it. Carefully lift the lower door off and place it to one side. Pull cover off. Unscrew hinge plate , rotate it by 180° and fit it on the opposite side. Pull off plastic cap , turn it through 180° and fit it back on to hinge plate . Refit cover on the opposite side.Remove cap\015from the bearing bush in the door and refit on the opposite side. Using a screwdriver, remove spring clampfrom underneath the door and fit it on the opposite side. Changing the door hinging 51
Changing over the doors Pull complete hinge pintogether with discand adjustable foot upwards and off. Remove cover cap. Undo screwsand take hinge plate off. Undo the screw of hinge part on hinge plateslightly. Fit it into the hole opposite in hinge plateand tighten up the screw. Refit cover capin the other hole. Remove coverand fit it into the holes on the opposite side.Screw hinge plateinto position on the opposite side using the twoouter long slots only. To make it possible to align the door later, do not replace thecentrescrew at this stage. Important. Screw the adjustable foot into hinge pinas far as it will go. Refit hinge pintogether with disc and adjustable foot. Important. The notch at the bottom of the hinge pin should face towards the back. Place the door onto hinge pin. Close the lower door. Changing the door hinging 52
Fit hinge pin\012into middle hinge plate in the lower door. The ridge on the hinge pin will fit into the notch in the hinge plate. Then fit the upper door on middle hinge pin\012. Close the upper door. Fit hinge plateonto the opposite side and secure it with screws. If necessary drill pilot holes for the screws or use a battery operated screwdriver.Fit coversandto their opposite sides. Align the door with the appliance housing using the long slots in the lower hinge plate. Then tighten the screws. Changing the door hinging 53
Refitting the handles Please make sure you follow the instructions below carefully when you refit the handles. The door seal will be damaged if the handle is fitted incorrectly. Loosely attach the handle to the opposite side of the door with the two front screws. Mounting platemust be positioned on the side of the door so that when the door isclosedit is flush with the side of the appliance. If this is not the case, tighten both grub screwswith a suitable allen key until mounting plate lines up correctly. Then tighten all 4 screws. Slide the side section of handle into the guides on the mounting plate until it clicks into place. It is important to check that the side section of handledoes not come into contact with the door seal when opening the door, as this would damage the door seal permanently. If, after you have refitted the handle, you find that the side section does touch the door seal when the door is opened: Realign mounting platewith grub screwsuntil the mounting plate and the side section of handleare at the correct angle and the side section does not touch the door seal when the door is opened. Changing the door hinging 54
The appliance doors can be aligned with the housing after they have been fitted. In the following illustration the door is not shown in the closed position to make it easier to see what you have to do. To align thelower dooruse the long outer slots in the lower hinge plate: Remove centre screwfrom the hinge plate. Slightly loosen both outer screws. Align the door by sliding the hinge plate to the left or right. Then tighten screwsagain. Screw does not need to be used again.To align theupper dooruse the long outer slots in the middle hinge plate: Slightly loosen both screws. Align the door by sliding the hinge plate to the left or right. Then tighten screws. Aligning the appliance doors 55
* The appliance depth is increased by approx. 35 mm for appliances with wall spacers fitted. Top box Appliance Housing unit WallThe appliance can be installed in a kitchen run. To match the height of the rest of the kitchen, the appliance can be fitted with a suitable top box. A ventilation gap of at least 50 mm depth must be allowed for behind the appliance across the entire width of the top box for air to circulate. The cross section of the air outlet under the room ceiling must be at least 300 cm 2to ensure that air can circulate without hindrance. Otherwise the appliance has to work harder, resulting in an increase in electricity consumption. The ventilation gaps must not be covered or blocked in any way. They should be dusted on a regular basis. When built into a kitchen run (max. depth 580 mm) the appliance can be installed directly next to a kitchen furniture housing unit. The appliance door will protrude in front of furniture fronts at the sides by 34 mm* and by 55 mm* in the middle of the door. This enables the door to be opened and shut without being obstructed. When installednext to a walla distance of approx. 55 mm must be maintained on the hinge side between the walland the appliance,so that the doors and the handles have sufficient space for opening. Installing the appliance 56
59 United Kingdom Miele Co. Ltd. Fairacres, Marcham Road Abingdon, Oxon, OX14 1TW Customer Contact Centre Tel: 0330 160 6600 E-mail: [email protected] Internet: www.miele.co.uk Australia Miele Australia Pty. Ltd. ABN 96 005 635 398 1 Gilbert Park Drive, Knoxfield, VIC 3180 Tel: 1300 464 353, Fax: (03) 9764 7149 Internet: www.miele.com.au Miele (Shanghai) Trading Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500, Fax: +86 21 6157 3511 E-mail: [email protected], Internet: www.miele.cn China 41/F - 4101, Manhattan Place 23 Wang Tai Road Kowloon Bay, Hong Kong Tel: (852) 2610 1331, Fax: (852)2610 1013 Email: [email protected] Miele (Hong Kong) Limited Miele India Pvt. Ltd. Ground Floor, Copia Corporate Suites Plot No. 9, Jasola New Delhi - 110025 Tel: 011-46 900 000, Fax: 011-46 900 001 E-mail: [email protected], Internet: www.miele.in India Miele Ireland Ltd. 2024 Bianconi Avenue Citywest Business Campus, Dublin 24 Tel: (01) 461 07 10, Fax: (01) 461 07 97 E-Mail: [email protected], Internet: www.miele.ie IrelandMalaysia Miele Sdn Bhd Suite 12-2, Level 12 Menara Sapura Kencana Petroleum Solaris Dutamas No. 1, Jalan Dutamas 1 50480 Kuala Lumpur, Malaysia Phone: +603-6209-0288 Fax: +603-6205-3768 Miele New Zealand Limited 8 College Hill Freemans Bay, Auckland 1011, NZ Tel: 0800 464 353, Fax: +64 9378 0146 Internet: www.miele.co.nz New Zealand Miele Southeast Asia Miele Pte. Ltd. 163 Penang Road # 04 - 02/03 Winsland House II Singapore 238463 Tel: +65 6735 1191, Fax: +65 6735 1161 E-Mail: [email protected] Internet: www.miele.sg Singapore Miele (Pty) Ltd 63 Peter Place, Bryanston 2194 P.O. Box 69434, Bryanston 2021 Tel: (011) 875 9000, Fax: (011) 875 9035 E-mail: [email protected] Internet: www.miele.co.za South Africa Miele Appliances Ltd. P.O. Box 11 47 82 Gold & Diamond Park Sheikh Zayed Road Building 6 / Offices Nos. 6-214 to 6-220 Dubai Tel: +971-4-341 84 44 Fax: +971-4-341 88 52 E-Mail: [email protected] Internet: www.miele.ae United Arab Emirates Carl-Miele-Straße 29, 33332 Gütersloh, Germany Manufacturer: Miele & Cie. KG
M.-Nr. 10 029 880 / 00en-GB KFN 11923 SD-2, KFN 11923 SD edt/cs-2