Miele K 9557 Id Operating And Installation Instructions

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Remember that the noise of the...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–the Miele Service Department
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
Guarantee
For information on the appliance
guarantee...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

To avoid a hazard due to instability
of the appliance, it must be fixed in
accordance with the instructions.
Location
The appliance should be installed in a
dry, well-ventilated room.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such...

Before installation
^Before installation remove the cover
strip, sealing strip and other
accessories from the appliance and
from the external rear wall of the
appliance.
^On no account should the spacers
be removed from the back of the
appliance. These ensure the gap
required between the back of the
appliance and the wall is maintained.
^Remove any cable clips from the rear
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
Does your old...

Niche height [mm]
A
K 9457 iD1220 - 1236
K 9557 iD1397 - 1413
K 9757 iD1772 - 1788
Building-in dimensions
36
 

The door hinges are set ex-works to
enable the door to be opened wide.
However, if the opening angle of the
door needs to be limited for any reason,
the hinge can be adjusted to
accommodate this.
–For example, if the appliance door
hits an adjacent wall when opened,
the opening angle can be limited to
90°.
^Place the locking pins supplied for
limiting the door opening into the
hinges from above.
The door opening angle is now limited
to 90°.–If you would like the appliance door
to be cushioned so that it...

Before building the appliance in, you
will need to decide on which side the
door is to be hinged. If left hand door
hinging is required, follow the
instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Appliance door
^
Open the appliance door.
^
Remove coversa,bandcwith a
screwdriver.
^
Loosen fixing screwsdat the top
and the bottom slightly.^Slide the door outwards and lift it off
e....

^Unscrew ball jointbusing a
spanner, and remove soft-close
mechanismctogether with the ball
joint.
Do not separate the soft-close
mechanism from the ball joint. This
would damage the mechanism.
^
Stand the appliance door up, and
loosen the hinges at the front (the
hinges remain open).
^
Remove screwsa, and use the
stoppers suppliedcto plug the
empty holes.
Do notclose up the hinges. Danger
of inury.^Replace the hinges in their diagonally
opposite cornersb.
^Use a powered screwdriver to secure
the hinges;...

^Push the appliance door onto the
pre-fitted screws, and then tighten
the screws.
^Replace coversa,bandc.
^
Replace the locking pins into the top
of the hinges to prevent the doors
opening too far.
Changing the door hinging
40