Miele K 5122 Ui Operating And Installation Instructions

Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
What to do if...
. . . the appliance does not get cool.
Make sure that the temperature
selector is not set at "0".
Check that the plug is correctly
inserted in the socket and switched
on....

If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the door while waiting for the
appliance to be serviced.
Problem solving guide
22
 

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele (see back cover for contact
details).
Please note that telephone calls may
be monitored and recorded for
training purposes (UK only).
When contacting your Dealer or the
Miele Customer Contact Centre, please
quote the model and serial number of
your machine. This information is given
on the data plate.
Guarantee
Please see the guarantee card
supplied.
In the U.K....

The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220 – 240 V 50 Hz supply. Connection
should be made via a fused plug and
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to install
a suitable residual current device
(RCD).
Connection should be made via a fused
plug and suitable switched socket
which is easily accessible. Do not
connect the appliance to the mains
electricity supply by an...

This appliance must be built in,
otherwise it could tip up.
Location
The appliance should be installed in a
dry, well-ventilated room.
It should not be installed where it is
exposed to direct sunlight or directly
adjacent to a heat-producing appliance
such as an oven or a radiator.
The room temperature should not go
above or below the climate range for
which the appliance is designed.
The higher the ambient temperature of
the room, the more energy the
appliance requires to operate.
Important: tropical /...

With abuilding under height of
820 mmthe plinth height can be set
between100 - 170 mm.
With a plinth height of exactly 100 mm,
the plinth can be fitted without altering
it.
With a height >100 mma cutout for
ventilation must be provided in the
plinth (see "Appliance installation").
Abuilding under height of 870 mmis
obtained by adjusting the appliance
feet. This increases the height of the
plinth, which, in this case, can be150 -
220 mm.
With a plinth height of exactly 150 mm,
the plinth can be...

Before installing the appliance decide
on the door hinging. If left hand door
hinging is required follow the
instructions below.
Unscrew the hingesat the top and
bottom of the door and the
appliance.
Fit the screwsloosely into the
opposite side.

Refit the hinges on the diagonally
opposite side of the door and then
tighten them.

Refit the appliance door onto
pre-fitted screws, then tighten the
screws.

Fit the covers suppliedinto the
holes.
Changing the door hinging
28
 

Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
K 5122 Ui 19 kg
Fitting a door which is heavier than
the maximum permitted could
damage the hinges.
Preparing the appliance

Bend both fixing tabs at the top of the
appliance forwards as far as they will
go.
Installation
Position the power supply cable
so that it can easily be connected to
the electricity supply after...

Increase the height of the appliance
using the adjustable feet until the top
of the appliance lies directly under
the worktop (A).
To increase the height
– of thefront screw feetturn them
anti-clockwisewith a suitable
spanner.
–
of therear left screw footinsert the
hex nut supplied into the opening at
the front of the applianceand
using a hex spanner turn it
anti-clockwise.
–
of therear right screw footinsert
the hex nut supplied into the opening
at the front of the applianceand
using a hex spanner...