Miele K 14820 Operating And Installation Instructions

Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered over. The air inlet and outlet
must not be covered or blocked in any
way. They should be dusted on a
regular basis.
Installation
^Remove any cable clips from the
back of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Remove
any hindrance.
^Carefully push the appliance into
position. The appliance can be
placed directly against a wall....

Appliance dimensions
ABC
K 14820 SD
K 14820 SD ed/cs1850 mm 600 mm 630 mm
^
Installation
42
 

The appliance is supplied with
right-hand door hinging. If left-hand
door hinging is required, the hinging
must be changed.
To change the door hinging, you will
need the following tools:
–a Phillips head screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed to change
the door hinging.
Removing the door handle
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbfirmly back out of
the guides on the mounting plate
(see...

Removing the SoftClose door
mechanism
The SoftClose door mechanism is at the
bottom of the door.
^Open the appliance door.
^Prise open panelafrom the
SoftClose mechanism: Insert a
flat-bladed screwdriver into the gap
from below and ease off the panel bit
by bit.
Take care not to damage the door
seal.
If the door seal becomes damaged,
the door will no longer close
properly and cooling will be
impaired.
^
Slide panelatowards the appliance,
and leave it hanging between the
door and the appliance.^Fit...

^Slide SoftClose mechanism bracket
fas far as it will go towards the
handle side of the door, and undo
screwsgon the SoftClose
mechanism.
^Using a flat-bladed screwdriver, slide
the SoftClose mechanism towards
the handle side of the door, and lever
it out at the side.
^Then place it to one side.
Changing over the door
Remove any food from the door
shelves.
^
Close the appliance door.
^
Remove coveraby sliding it
forwards from the back and then
lifting it off.^Remove coverbby pulling it
upwards.
Caution!...

^Then fit coveretogether with
retaining platefon the opposite
side.
^Remove caphfrom the bearing
bush in the door and refit on the
opposite side.
^
Pull hinge pinawith discband foot
cupwards to remove them.
^
Remove coverd.
^
Undo screwseand take hinge plate
foff.^Unscrew bearinghfrom hinge plate
f, rotate it by 180° and refit into the
hole on the opposite side of the hinge
plate.
^Place capdin the other hole.
^Remove covergand fit it into the
holes on the opposite side.
^Screw hinge platefinto position...

^Fit hinge plateconto the opposite
side and secure it with screwsd.
If necessary, drill pilot holes for the
screws.
^Fit coversaandbto their opposite
sides.
^Realign the door with the appliance
housing again using the long slots in
the lower hinge plate. Then tighten
the screws.
Replacing the SoftClose door
mechanism
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Insert the SoftClose mechanism back
into the door, starting at the
right-hand side.
^Using a flat-bladed...

^Attach panelbto SoftClose
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is secured.
^Remove retaining clipg.
^
Replace panelbonto the SoftClose
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the appliance door.Refitting the handle
Please make sure...

It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door as this would
damage the door seal permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing...

The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what happens
next.
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be refitted.
Aligning the appliance door
50