Miele H 251 User Manual

Downloaded from www.Manualslib.com manuals search engine \
The voltage and rated load are given
on the data plate, visible when the
oven door is open. Please ensure that
these match the household mains sup-
ply. 
Underbench oven
The appliance is supplied with a 3-core
cable for connection to a 230-240 volt
50 Hz supply.
The fuse rating is 32 amps for the E-
model with hob.
Wall oven
The appliance is supplied with a 3-core
cable for connection to a 230-240 volt
50 Hz supply.
The fuse rating is 13 amps for...

Downloaded from www.Manualslib.com manuals search engine Electrical connection @äAll electrical work should be under-
taken by a competent person in
strict accordance with national and
local safety regulations.
The voltage and rated load are given
on the data plate, visible when the
oven door is open. Please ensure that
these match the household mains sup-
ply. Please quote these data, and the
model and serial number when contact-
ing the Miele Service dept.
Connection of this appliance should be
made...

Downloaded from www.Manualslib.com manuals search engine Installation - Ceramic hobs
These hobs are classified in Germany
as Y class for heat protection. They
must be positioned so that there is ade-
quate ventilation. There may be a wall
at the rear and wall or tall units at one
side. On the other side, however, no
unit or divider must stand higher than
the hob. 
Because of the heat given off, there
must be a minimum distance as fol-
lows: 
–40 mm between the worktop 
cut-out and adjacent furniture, 
e....

Downloaded from www.Manualslib.com manuals search engine Loosen the screws f.
Under no circumstances should
sealant find its way between the
frame of the top part of the hob and
the worktop.
This could cause difficulties or even
damage should the hob ever need to
be taken out for servicing. The rub-
ber edge 
b under the top part of the
hob provides a sufficient seal for the
worktop 
d.
Set the ceramic hob c in the cut-out
and centre it. 
(The Miele inscription must be
legible at the front).
Turn the...

Downloaded from www.Manualslib.com manuals search engine Installation - Hobs with enclosed hotplates
These hobs are classified in Germany
as Y class for heat protection. They
must be positioned so that there is ade-
quate ventilation. There may be a wall
at the rear, and wall or tall units at one
side. On the other side however no unit
or divider must stand higher than the
hob.
Because of the heat given off, there
must be a minimum distance as fol-
lows: 
–40 mm between the worktop 
cut-out and adjacent...

Downloaded from www.Manualslib.com manuals search engine Installation - Cooker
Turn off the mains electricity supply
to the isolator.
Connect cooker cable to isolator.
Align the cooker in front of the base
unit.
Connect the hob plug to the socket
on the cooker.
Push the appliance into the oven
base unit as far as the oven trim and
align.
Then open the oven door and screw
the oven to the side panels of the
base unit through the two holes, one
on each side of the oven trim.
The appliance must only be...

Downloaded from www.Manualslib.com manuals search engine Installing the oven
The oven is designed to be built
into a tall unit. If you wish to install it
in a base unit, the stainless steel rail
above the control panel must be re-
placed by a sealing strip. The seal-
ing strip offers additional protection
from any liquids that might spill
down from the worktop, and can be
purchased from the Miele Spare
Parts dept.
Turn off the mains electricity supply
to the isolator.
Connect the oven to the electricity...

Downloaded from www.Manualslib.com manuals search engine Alteration rights reserved / 22 / 003 GB / IRL / AUS / NZ / ZA – 2398
M.-Nr. 05 008 610 (H 250-1, H 250, H 251, H 260, H 261)
This paper consists of cellulose which has been bleached without the use of chlorine.