Miele G 832 Sc Manual

							Additional features
Top Solo (18)
Using Top Solo will save water and
energy.
This program is recommended when
there is only a small load to clean. Top
Solo can be selected with all pro-
grams.
With this feature, water is directed only
to the top and middle spray arms in the
dishwasher. This means that the water
jets are only aimed at items in the up-
per basket and the cutlery tray.
The middle spray arm also directs wa-
ter downwards, so lightly soiled plates
or platters can be placed in the lower
basket.
When using this program, do not place
pots, bowls or other hollow containers
in the lower basket.
Because a smaller load is being
washed the amount of detergent rec-
ommended can be reduced to 1
1/4tablespoons.^Turn the dishwasher on using the
On/Off button (13).
The Start/Stop (17) indicator will flash.
^Select a program using the program
selection buttons (19).
^Press the Top Solo button (18).
The Top Solo indicator and the se-
lected program indicator will light.
^Press the Start/Stop button (17).
The program will begin.
Operation
31 
						

							Extended drying
If desired drying results are not consis
-
tently achieved, the turbothermic cool
-
ing fan can be programmed to run an
extra 14 minutes at the end of each
program.
The Extended drying feature can also
be activated to prevent condensation
from collecting on the steam deflector.
Turning extended drying on/off
^Make sure the dishwasher is turned
off.
^Press and hold the Start/Stop (17)
button and at the same time turn the
dishwasher on using the On/Off but-
ton.
Release the Start/Stop button within
two seconds.
^Press the Top Solo (18) button.
The Salt (15) indicator will flash and
the End (16) indicator will light.
If this is not the case, the above steps
must be repeated.The extended drying time isoffif the
top program indicatorflashes.
The extended drying time isonif the
top program indicatorlights.
If the the correct drying time is set:
^Turn off the dishwasher.
If the drying time is incorrect:
^Press the Top Solo button (18).
^Press the Start/Stop (17) button
twice.
The Start/Stop (17) indicator will flash.
The changed extended drying option
will be stored.
^Turn off the dishwasher.
Operation
32 
						

							With the aid of the following guide, minor problems can be fixed without a service
call.
,Repairs should only be carried out by a qualified and trained person in ac
-
cordance with local and national safety regulations. Unauthorized repairs could
cause personal injury or machine damage.
What if … Possible fault Fix
the dishwasher does not
start?The door is not properly
closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse is defective or
the breaker has tripped.Reset the circuit breaker
Make sure it is a 15 A
breaker.
the dishwasher stops
during a program?The fuse or breaker has
tripped.Reset the circuit breaker
Make sure it is a 15 A
breaker.
the Intake indicator is
lit / flashing?The water valve is closed. Open the water valve.
The filter in the water inlet
is blocked.See maintenance instruc-
tions.
The waterproof system
has activated.Call the Miele Technical
Service Department.
The flow pressure at the
water inlet is less than
4.5 psi (0.3 bar).Contact a plumber.
Frequently asked questions
33 
						

							What if … Possible fault Fix
the Drain indicator
flashes and the program
stops?The triple filter in the wash
cabinet is clogged.Clean the filter, see main
-
tenance instructions.
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve, see
maintenance instructions.
The drain hose is kinked. Remove the kink.
the End, Start/Stop
and Top Solo indica
-
tors flash at the same
time at the end of a pro
-
gram?There may be a technical
fault.–Press the Start/Stop
button.
–Turn off the dish
-
washer.
A few seconds later:
–Turn the dishwasher
on.
–Select the desired pro-
gram.
–Press the Start/Stop
button.
If the indicators flash
again, there is a technical
problem.
–Call the Miele Technical
Service Department.
Frequently asked questions
34 
						

							What if … Possible fault Fix
there is a knocking
noise in the wash cabi
-
net?The spray arm is hitting an
item in the basket.Interrupt the program, re
-
arrange items blocking
the spray arms.
there is a rattling noise?Items are not secure in
the wash cabinet.Interrupt the program and
rearrange loose pieces.
there is a knocking
noise in the water
pipes?This may be caused by
the installation or the di
-
ameter of pipe.This has no effect on the
dishwasher. If in doubt
contact a plumber.
the dishes are not dry,
glasses and cutlery are
spotted?The rinse aid setting may
be too low, or the rinse aid
reservoir is empty.Increase the dosage or
refill the reservoir, see
Before using for the first
time.
Extended drying is not ac
-
tivated.Activate the Extended
drying feature.
Dishes were taken out too
soon.Leave dishes in longer.
dishes are not clean?The dishes were not
loaded correctly.See Loading the dish-
washer.
The program was not
powerful enough.Select a more intensive
program, see Program
guide.
Not enough detergent
was dispensed.Use more detergent, see
Adding detergent.
The spray arm jets are
clogged.Clean the spray arm jets,
see maintenance instruc-
tions.
The triple filter is clogged
or not correctly seated.Clean and reseat the filter,
see maintenance instruc-
tions.
The non-return valve is
blocked while open. Wa-
ter runs back into the
wash cabinet.Clean the drain pump and
the non-return valve, see
maintenance instructions.
Frequently asked questions
35 
						

							What if … Possible fault Fix
tea or lipstick stains
have not been com
-
pletely removed?The wash temperature of
the selected program was
too low.Select a program with a
higher temperature.
Not enough detergent
was used.Use more detergent.
white residue is visible
on cutlery and dishes,
clouding occurs on
glassware and film can
be wiped off?Not enough rinse aid was
used.Increase the dosage,
see Before using for the
first time.
The salt reservoir is
empty.Add reactivation salt,
see Before using for the
first time.
The salt reservoir cap was
not correctly screwed on.Reseat it making sure it
screws back on correctly.
The programmed setting
of the water softener is too
low.Raise setting of the water
softener , see Before
using for the first time.
there is a bluish sheen
on the surface of
glasses and film can be
wiped off?The rinse aid dosage is
set too high.Reduce the dosage, see
Before using for the first
time.
glasses are dull and dis-
colored and film cannot
be wiped off?Glasses are not dish-
washer safe.There is no remedy.
Only wash dishwasher
safe glasses.
Frequently asked questions
36 
						

							What if … Possible fault Fix
plastic items are discol
-
ored?Natural dyes e. g. from
vegetables may be the
cause. Not enough deter
-
gent was used to break
down natural dyes.Use more detergent, see
Adding detergent.
Discoloration is perma
-
nent.
there are rust stains on
cutlery?The salt reservoir cap was
not screwed on properly.Reseat and screw the cap
on firmly.
The affected items are not
corrosion resistant.There is no remedy.
Only wash dishwasher
safe cutlery.
detergent is left in the
dispenser at the end of a
program?The dispenser was damp
when detergent was
added.Dry the dispenser before
adding detergent.
the detergent dispenser
lid can not be closed
properly?Detergent residue is
blocking the catch.Remove the residue.
water remains in the
wash cabinet at the end
of a program?The triple filter in the wash
cabinet is clogged.Clean the filter,
see maintenance
instructions.
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve,
see maintenance
instructions.
The drain hose is kinked. Remove the kink.
Frequently asked questions
37 
						

							In the event of a fault which you cannot
correct yourself please contact:
–Your Miele Dealer
or
–The Miele Technical Service Depart
-
ment.
USA 1-800-999-1360
[email protected]
CDN 1-800-565-6435
[email protected]
When contacting the Miele Technical
Service Department, please quote the
model and serial number of your appli-
ance.
These can be found on the data plate
on the upper inside edge of the dish-
washer door.Program update function - PC
The Program Correction (PC) allows a
technician to update the dishwasher to
make use of new technology.
For example, if a detergent with good
wash results using only cold water be-
comes available, the wash programs
can be modified to take advantage of
this.
After sales service
38 
						

							To transport the dishwasher, e. g. when
moving to a new home, note the follow
-
ing:
–Empty the dishwasher.
–Secure any loose parts, e. g. hoses,
cables, cutlery baskets.
–Transport the dishwasher in the up
-
right position.
If unavoidable it may be transported
on its back.
Do not transport it on its side or on
the door. Residual water in the ma
-
chine could leak and cause electrical
damage.
Transport
39 
						

							40