Miele G 7881 User Manual

Liquid option
As a separate option, this machine can
be fitted with a dispenser pump for
automatic liquid detergent dispensing
(DOS Module K 60). This is connected
externally.
The optional DOS Module K 60 is
supplied with its own installation and
connection instructions.
The liquid detergent is automatically
dispensed in the wash step of the
program.
^Place the container of detergent next
to the machine.
See "Programming functions" to prime
the dispensing system and set the
dispensing amount....

How to switch on
^Close the door.
^Press the "ON/OFF" button.
A dot will appear in the display when
the program selector is at the
12 o'clockfposition.
Starting a program
Always choose a program to match the
type and soiling level of the washload.
See theprogram guidefor a
description of the various programs
available.
^Turn the program selector left or right
to the desired program.
The temperature of the first wash for the
program selected will show in the
display, except for the...

While the program is running, any of the
following displays can be selected:
–Actual temperature,
–Elapsed program time and
–Active wash block.
^Press the "Display"ßbutton to
toggle between the displays.
Progress indicator
The indicator light for the active program
is lit while the program is running:
Recharging
Pre-Wash1+2
Wash1+2*
Rinse1-4/
Final rinse1+2
Dry
Complete (program parameters
achieved)
End of program
A program is completed when the
indicator light "Complete", in the
progress...

How to switch off
^Press the "ON/OFF" button and let it
pop up.
The door is equipped with an
electric lock and can only be
opened if the "ON/OFF" switch is
pressed (see "Opening and closing
the door").
How to cancel a program
Avoid cancelling a running program
unless absolutely necessary, for
example, if an item is moving around
excessively or the wrong program has
been selected.
^Turn the program selector to the
12 o'clock positionf.
The program is cancelled after approx.
2...

For future servicing, be sure to document any changes made to the standard
factory settings.
Enter the information in the field(s) provided.
General information:
–Program selector positions that have no assigned function are represented by a
bar (-) in the middle of the display.
–To call up the programming level, use the 12 o'clock positionf.
The statusE..will appear in the display.
–Any program or dosing changes in connection with the preparation of medical
devices must be documented. In such cases,...

DOS 1 dispensing (detergent)
Setting the liquid detergent dispensing concentration
The dispensing concentration only needs to be set for liquid detergents. Set
the concentration according to the detergent manufacturer's
recommendations. Do NOT change the setting if you are using powder
detergent in the door dispenser.
Step Display / Result
^Activate the programming mode as
per page 35.
^Press the "Drying"0button until E02
appears in the display.E02
^Turn the program selector to the...

Priming the liquid detergent dispensing system
The dispensing system does not need to be primed (cleared of air) unless:
– the dispensing concentration is being set for the first time,
– the liquid detergent container was not refilled in time and became completely
empty.
Step Display / Result
^Activate the programming mode as per
page 35.
^Press the "Drying"0button until E02
appears in the display.E02
^Turn the program selector to the 1 o'clock
position.d§1
^Press the...

DOS 3 dispensing (neutralizer)
Setting the neutralizer concentration
Set the neutralizer dispensing concentration according to the manufacturer's
recommendations or to meet specific requirements.
Step Display / Result
^Activate the programming mode as per
page 35.
^Press the "Drying"0button until E02
appears in the display.E02
^Set the program selector to the 6 o'clock
position.The programmed dispensing
concentration appears in the
display,
e.g.,0.10= 0.10 %
^Press or hold down the...

Priming the neutralizer dispensing system
The dispensing system does not need to be primed (cleared of air) unless:
– the dispensing concentration is being set for the first time,
– the processing chemical container was not refilled in time and became
completely empty.
Step Display / Result
^Activate the programming mode as per
page 35.
^Press the "Drying"0button until E02
appears in the display.E02
^Set the program selector to the 5 o'clock
position.d§3
^Press the "Display"ßbutton....

Buzzer
The buzzer can be programmed for the following functions:
– Program end = Constant buzzer,
– Fault warning = Buzzer at 1-second intervals, and
– Sample-collection signal = sets of 3 short beeps followed by a 2-sec pause.
Contact Miele Customer Service to program the sample-collection signal.
The numbers shown in the display correspond to the following settings:
20Buzzer off
21End of program (factory setting)
22Error
23End of program + Error
24Sample-collection signal
25End of program +...