Miele G 5980 Operating Instructions

To open the door
At the end of programmes with a drying
phase (see "Programme chart"), the
door will open automatically a little in
order to help the drying process.
This function can be deactivated, if
preferred (see "Settings menu,
AutoOpen").
Pull the handle.
If the door is opened during operation,
all functions are automatically
interrupted.
Keep the area around the door
free of obstructions.
To close the door
Push the baskets right in.
Then raise the door up and push until
the...

Display
The display is used to select the
following:
–the programme
–extras
–the delay start time
–the Settings menu

–information
During a programme, the display
shows the following (when the door is
opened):
– the name of the programme
– the current time of day
– the stage the programme is at
– the estimated time left for the
programme to run
– any relevant fault messages and
notes
To save energy, the dishwasher
switches off after a few minutes if you
do not press any buttons during this
time (see...

Basic settings
Welcome screen
Switch the dishwasher on with the On/Off button.
If the dishwasher is being switched on for the first time, the
welcome screen will appear after a few seconds.
Language
The display will then change automatically to the screen for
setting the language.
eština
Language
dansk
Select the language you want and confirm this withOK.
A tick
will appear next to the language that has been set.
Clock display
The display will then change to the screen for setting the
clock...

Time
The display will then change to the screen for setting the
time.
+12
:00
-Please set the time OK
Set the hours with+/-and confirm withOK.
Then set and confirm the minutes.
Water hardness
The display will then change to the screen for setting the
water hardness.
15°d
Water hardness
16°dOK
– The dishwasher must be programmed for the water
hardness in your area.
– Your local water authority will be able to advise you of the
water hardness level in your area.
– Where the water hardness...

The dishwasher is programmed at the
factory for a water hardness level of
2.7 mmol/l (15 °d - German scale).
Select the water hardness you want,
and confirm your selection with
OK.
See "Programming the water
hardness level" for further
information.
These settings will be saved in memory
after the dishwasher has been through
one complete programme.
Finally, two messages will appear in the
display.
After confirming these,
Rinse aid low
andInsufficient saltmay then appear
in the display to remind...

Water softener
In order to achieve good cleaning
results, the dishwasher needs to
operate with soft water. Hard water
results in the build-up of calcium
deposits on crockery and in the
dishwasher.
Mains water with a hardness level
higher than 0.7 mmol/l (4 °d – German
scale) needs to be softened. This takes
place automatically in the integrated
water softener. The water softener in
this dishwasher is suitable for a water
hardness level of up to 12.6 mmol/l
(70 °d - German scale).
– The water softener...

Programming the water hardness
level
Switch the dishwasher on with the
On/Off button, if it is switched off.
The main menu will appear in the
display.
If the memory function is activated, the
programme menu for the programme
last selected will be displayed instead
(see "Settings menu
, Memory"). If this
is the case, press the Clear button
to switch to the main menu.
In the "Settings menu
" select the
Water hardnessoption.
A tickwill appear beside the water
hardness which has been...

Before using the appliance for
the first time, you require:
–approx. 1 kg dishwasher salt*,
–domestic dishwasher detergent*,
–rinse aid* formulated for domestic
dishwashers.
* See "Optional accessories"
Every dishwasher is tested at the
factory.
There will be residual water in the
appliance from this test. It is not an
indication that it has been used
previously.
Filling the salt reservoir
If the water in your area is very soft
and constantlylower than
0.7 mmol/l (4 °d - German scale),
you do not...

When filling the salt reservoironly
open the door halfwayto ensure
that all the salt gets into the reservoir.
Press the button on the lid of the salt
reservoir in the direction of the arrow
until the flap springs open.

Lift up the funnel.
Do not fill the salt reservoir with
water.
Add salt only until the reservoir is full
or until water runs out of the opening.
The salt reservoir holds approx. 1 kg
of salt, depending on the brand
used.
Do not add any more than 1 kg of
salt.
As the salt reservoir is...

Salt indicator
Fill the salt reservoir with dishwasher
salt for reactivation when the

Insufficient saltmessage
appears. (If it appears during a
programme, wait until the end of the
programme).
Confirm with
OK.
The "Insufficient salt" message will go
out.
After the salt reservoir has been filled,
the "Insufficient salt" message may still
appear in the display if the salt
concentration has not yet reached the
correct level.
If this is the case, confirm again with
OK.
The insufficient...