Miele G 4570 Operating Instructions

							Cleaning the drain pump and
non-return valve
If the dishwasher is not completely
drained at the end of a program, the
drain pump or non-return valve may be
blocked.
Turn off the dishwasher and pull the
plug.
Remove the triple filter (see Triple
filter system).
Use a cup or bowl to scoop water out
of the wash cabinet.

Tilt the locking clamp to the side.

Pull out the non-return valveand
rinse it under running water.

Remove all foreign objects from the
non-return valve.The drain pump is beneath the
non-return valve (see arrow).
Remove all foreign objects from the
drain pump (glass or bone splinters).
Before returning the non-return valve,
check that the drain pump is not
blocked. Spin the propeller several
times in both directions to check for
obstructions.
Carefully reinsert the non-return valve
and secure it with the locking clamp.
Make sure the locking clamp
clicks into place!
Cleaning and Care
51
 
						

							52
 
						

							Installation Instructions
Please refer to the Installation Diagram supplied with these instructions.
To comply with IEC sound testing protocols, please contact Miele for additional
instructions.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
 
						

							Disposal of the packing
material
The cardboard box and packaging
protect the appliance during shipping.
These materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old machine
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
Help to protect the environment
54
 
						

							Installation, repairs and other
work by unqualified persons could
be dangerous.
Check that the voltage, frequency
and fuse rating shown on the data
plate match the household mains
supply.
The power outlet must be accessible
after installation. Do not use an
extension cord to connect the
dishwasher to the mains. Danger of
overheating! See data plate on the
right side of the door.
A damaged power cord must only
be replaced with a genuine Miele
cord by a Miele service technician
or a qualified technician.
GROUNDING INSTRUCTIONS
THIS APPLIANCE MUST BE
GROUNDED.
In the event of a malfunction or
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for the electrical
current. This appliance is equipped
with a cord having an equipment
grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local
codes and ordinances.
Improper connection of the
equipment grounding conductor
can result in electric shock. Do
not modify the plug provided with
the appliance; if it will not fit the
outlet, have a proper outlet
installed by a qualified electrician.
If there is any question
concerning the proper electrical
connection or grounding of this
appliance to the power supply,
please consult a licensed
electrician or call Miele’s
Technical Service Department:
1-800-999-1360
1-800-565-6435
Specifications
The dishwasher comes equipped
witha4ft(1.2 m) power cord with a
molded plug for connection to 120 V,
60 Hz, 15 A grounded receptacle.
Electrical connection
55
 
						

							Waterproof system
All Miele dishwashers have a safety
valve located on the incoming water
line and a sealed underside with a
water sensor.
If a fault occurs, the water intake is
stopped and the drain pump is
activated. Water damage, if any, is
minimized.
Providing the dishwasher was installed
correctly by a Miele technician, the
waterproof system will protect you from
water damage throughout the lifetime of
the machine.
Connection to the water
supply
Installation, repairs and other
work by unqualified persons could
be dangerous.
Do not drink water from the
dishwasher!
–The dishwasher can heat its own
water to the temperature required by
the wash program. This allows for
connection of the machine to either a
hot (max. 140°F / 60°C) or cold water
source.
For lowest energy consumption and
fastest possible wash times connect
the dishwasher to a hot water
source. All programs use hot water in
the rinse cycles.
– The inlet hose is approximately 5 ft.
(1.5m) long.
–
The water inlet hose comes
equipped with a 3/4 female hose
thread connector. This can be
directly connected to a water supply
with 3/4 MHT (male hose thread
ends).
If not connected directly to a water
supply valve, an appropriate
adapter (not required) is required.
Plumbing
56
 
						

							–Water pressure: Must be between
4.5 - 145 psi (0.3 - 10 bar).
–If the water pressure if lower, a
Water Intake notification will be
shown. See Frequently Asked
Questions for more information.
–If the water pressure is higher than
shown, a pressure reducing valve
must be used.
Ensure that the water connection is
secure after the first use.
To prevent damage to the
dishwasher, it must only be
connected to a fully vented drainage
system.
Do not cut the intake hose. It
contains electrical wiring. If the hose
is cut, the dishwasher will not work.
There will be a water leak and you
could be injured. If the hose is too
long, coil it neatly and place it
behind the machine.
Plumbing
57
 
						

							Drainage
–The machine comes equipped with a
built-in non-return valve on the
discharge side to prevent waste
water from flowing back into the
dishwasher.
–The dishwasher is equipped with a
5 ft (1.5 m) flexible drain hose with an
internal diameter of 7/8 (22 mm).
–Drain hose extensions and adapters
can be ordered from Miele.
The maximum drain hose length is
13 ft. (4 m), max. drain height: 39
(1 m).
– Use the clamp provided to attach the
hose to the dishwashers P trap or
disposal connection (see the
Installation Diagram).
The hose must always be attached
on the sink side of the P trap.
When attaching the hose to a
garbage disposal fitting, make sure
the plug which is normally blocking
the fitting is knocked out or
removed.
–
The hose can be angled to the left or
right side at the rear of the machine.
–
The existing nipple that the drain
hose is connected to may be
designed for various hose diameters.
If the nipple diameter is to large or to
small it should be replaced or an
adapter may be used. If the nipple
extends more than 2 (50 mm) into
the drain hose it should be
shortened, or the hose could clog.–The drain hose must not be
shortened.
Make sure the hose is not kinked
or cut when pushing the machine
under the countertop.
Venting the drainage system
If the dishwasher drain hose is
connected to a floor drain or to a drain
pipe that is less than 8 (20 cm) above
the floor, the drain must be vented.
Otherwise the water inside the
dishwasher may siphon out during the
wash program.
Open the dishwasher door and
remove the lower basket.

Pull the lower spray arm firmly
upwards to remove.

Cut off the vent cap located at the
right rear of the triple filter system, as
illustrated.
Plumbing
58
 
						

							59
 
						

							Alteration rights reserved / 1511
G4570 /
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.M.-Nr. 07 909 300 / 02