Miele G 4570 Operating Instructions

							At the end of a program
Open the door slightly to check
whether the program has finished.
The indicator for the selected program
has gone out.
The program has not yet finished as
long as the program indicator is still
flashing. Close the door again so
that the program runs to the end.
In the Express program, the drying
fan will run for a few minutes after
the program is completed.
You can now empty the dishwasher.
To avoid damage to counter
tops rom steam, open the door after
the the end of the program either
fully (never ajar) or keep it closed
until you are removing all the dishes.
Turning off
At the end of a program:
Open the door.
Press thebutton to turn the
dishwasher off.
The dishwasher continues to use
electricity until turned off with the
button.
To be safe, turn the water supply off if
the dishwasher is unattended for an
extended period of time, e.g. during
vacation.
Unloading the dishwasher
Dishes tend to break and chip more
easily when they are hot.
Allow the dishes to cool until they are
comfortable enough to handle before
unloading them.
If you open the door fully after switching
off, the dishes will cool much faster.
Unloading the lower basket first will
prevent water drops from the upper
basket and cutlery tray (depending on
model) from dropping onto dishes in
the lower basket.
Use
31
 
						

							Interrupting a program
A program is interrupted as soon as the
door is opened.
If the door is closed again, the program
will continue from where it was
interrupted.
Water in the dishwasher is hot.
Danger of scalding.
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Close the door
firmly until it clicks into place.
Changing a program
If the detergent dispenser flap is
already open, do not change the
program.
If a program has already started and
you wish to change it:
Open the door.
Press thebutton.
Press thebutton.
Select the desired program with the
Program selection button.
Start the program by closing the
door.
Use
32
 
						

							Buzzer
A signal sounds at the end of a
program and when a fault occurs.
The buzzer at the end of a program
sounds four times in intervals with a
brief break in between.
The buzzer for a fault sounds four times
without pausing.
The buzzer is activated by default.
It can be turned off, so it does not
sound at the end of a program. The
buzzer for a fault cannot be turned off.
Open the door.
Turn the dishwasher off with the
button.
Press and hold the Program button
and turn the dishwasher on
simultaneouslyusing thebutton.
Keep the program button pressed for
at least four seconds until the lower
right program indicator lights up.
If it does not come on, start over.Press the Program button four times
briefly.
The Intake/Drain indicator flashes 4
times at short intervals.
The sequence of flashing by the upper
right program indicator shows whether
the program end buzzer is turned on or
off:
–upper right program indicator
flashing: buzzer is turned on
–upper right program indicator is off:
buzzer is turned off
To change the setting press the
Program button (for at least one
second) until the Intake/Drain
indicator lights up.
Now press the Program button
briefly.
The setting is saved immediately.
Turn the dishwasher off with the
button.
Additional options
33
 
						

							Factory default
All settings can be reset to factory
default.
Open the door.
Turn the dishwasher off with the
button.
Press and hold the Program button
and turn the dishwasher on
simultaneouslyusing thebutton.
Keep the Program button pressed for
at least four seconds until the lower
right program indicator lights up.
If it does not come on, start over.
Press the Program button briefly 12
times.
The Intake/Drain indicator flashes
once long and twice short.The sequence of flashing by the upper
right program indicator shows whether
a setting has been set differently to the
default setting.
–upper right program indicator
flashes:
all values are set to the default
settings.
–upper right program indicator is off:
at least one setting has been
changed.
To reset the dishwasher to factory
default press the Program button
(for at least one second) until the
Intake/Drain indicator lights up.
Now press the Program button
briefly.
The setting is saved immediately.
Turn the dishwasher off with the
button.
Additional options
34
 
						

							Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
The dishwasher
does not start.The door is not properly
closed.Push the door firmly shut.
The machine is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker
(see the data plate for minimum
amperage).
The dishwasher is not
turned on.Press thebutton and select a
program.
The dishwasher
stops during a
program.The circuit breaker has
tripped.– Reset the circuit breaker (see
the data plate for minimum
amperage).
– If the circuit breaker trips
again, contact Miele.
The buzzer sounds.
All indicator lights
of the program
selection flash
when the door is
open.There may be a
technical fault.–
Turn the dishwasher off with
thebutton.
After a few seconds:
–
Turn the dishwasher on.
–
Select the desired program
with the Program selection
button.
–
Close the door.
If the indicator lights flash again,
a technical fault has occurred.
–
Contact Miele.
The drain pump
may also be
running when the
door is open.The waterproof system
has activated.–
Turn off the water supply.
–
Contact Miele.
Frequently Asked Questions
35
 
						

							Faults in the water intake/water drain
Problem Possible fault Solution
The dishwasher
stops shortly after
the program starts.
The buzzer sounds.
The Intake/Drain
indicator flashes and
lights up alternately
when the door is
open.The water supply valve
is closed.–Open the water supply valve
all the way.
The dishwasher has
stopped.
The buzzer sounds.
The Intake/Drain
indicator flashes
when the door is
open.Before fixing the fault:
– Turn the dishwasher off with
thebutton.
Fault in the water intake. – Open the water supply valve
all the way.
– Clean the water intake filter
(see Cleaning and Care).
– The water pressure at the
water connection is less than
30 kPa (0.3 bar/4.35 psi).
Consult a plumber.
Fault in the water drain.
There might be water in
the wash cabinet.–
Clean the triple filter (see
Cleaning and care).
–
Clean the drain pump (see
Cleaning and Care).
–
Clean the non-return valve
(see Cleaning and Care).
–
Remove any kinks in the
drain hose.
Frequently Asked Questions
36
 
						

							General problems with the dishwasher
Problem Possible fault Solution
The display is dark
and only the 
indicator lights.The indicator lights go out
automatically to save
energy (Standby).Press any button (except
) to come out of Standby
mode.
Detergent residue is
left in the dispenser at
the end of a program.The dispenser was damp
when detergent was added.Dry the dispenser before
adding detergent.
The detergent
dispenser lid cannot
be closed properly.Detergent residue is
blocking the catch.Remove the residue.
The door and the
interior walls are still
wet after a program
has finished.This is not a fault!
It is the normal operating
mode of the drying system.None!
The moisture will
evaporate after a short
time.
Water remains in the
wash cabinet at the
end of a program.Before fixing the fault:
– Turn the dishwasher off
with thebutton.
The triple filter in the wash
cabinet is clogged.Clean the triple filter (see
Cleaning and care).
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve (see
Cleaning and care).
The drain hose is kinked. Remove any kinks from the
drain hose.
Frequently Asked Questions
37
 
						

							Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinetThe spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinetItems are not secure in the
wash cabinet.Interrupt the program, and
rearrange loose pieces.
A foreign object (e.g. a
cherry stone) has become
lodged in the drain pump.Remove the foreign object
from the drain pump (see
Cleaning the drain pump
and non-return valve)
There is a knocking
noise in the water lineThis may be caused by
the installation or the
diameter of the pipe.This has no effect on the
dishwasher. If in doubt,
contact a plumber.
Frequently Asked Questions
38
 
						

							Poor cleaning results
Problem Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program (see Program
Guide).
Not enough detergent was
dispensed.Use more detergent, or
change the detergent.
The spray arms are blocked. Turn the spray arms and
rearrange the dishes if
necessary.
The triple filter in the wash
cabinet is clogged or not
correctly inserted.
The spray arm jets might be
clogged as a result.Clean the filter and insert it
correctly.
Clean the spray arm jets, if
required (see Cleaning and
care).
The non-return valve is stuck
open and blocked. Wash
water will run back into the
wash cabinet.Clean the drain pump and
the non-return valve (see
Cleaning and care).
Glasses and
cutlery show
streaks. There is a
bluish sheen on the
surface of glasses
and a film which
can be wiped off.The rinse aid dosage is set
too high.Reduce the dosage (see
Rinse aid).
Frequently Asked Questions
39
 
						

							Problem Possible fault Solution
Dishes are not dry,
glasses and
cutlery are
spotted.The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling (see Rinse aid).
Dishes were taken out too
soon.Leave dishes in longer (see
Use).
A Tab product was used.
These products have a low
drying effect.Change the detergent, or
refill the rinse aid (see Rinse
aid).
White residue is
visible on cutlery
and dishes.
Clouding occurs
on glassware and
cutlery; film can be
wiped off.Not enough rinse aid was
used.Increase the dosage (see
Setting the rinse aid
dosage).
The salt container is empty. Refill the salt container (see
Filling the salt container).
The salt container lid was not
correctly screwed on.Reseat it making sure it
screws back on correctly.
Unsuitable Tab products
were used.Use a different detergent.
Use normal (powder or gel)
detergent.
The water softener is
programmed on too low a
setting.Program a higher water
softener setting (see Water
softener).
Frequently Asked Questions
40