Miele G 4570 Operating Instructions

At the end of a program
Open the door slightly to check
whether the program has finished.
The indicator for the selected program
has gone out.
The program has not yet finished as
long as the program indicator is still
flashing. Close the door again so
that the program runs to the end.
In the Express program, the drying
fan will run for a few minutes after
the program is completed.
You can now empty the dishwasher.
To avoid damage to counter
tops rom steam, open the door after
the the end of the program...

Interrupting a program
A program is interrupted as soon as the
door is opened.
If the door is closed again, the program
will continue from where it was
interrupted.
Water in the dishwasher is hot.
Danger of scalding.
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Close the door
firmly until it clicks into place.
Changing a program
If...

Buzzer
A signal sounds at the end of a
program and when a fault occurs.
The buzzer at the end of a program
sounds four times in intervals with a
brief break in between.
The buzzer for a fault sounds four times
without pausing.
The buzzer is activated by default.
It can be turned off, so it does not
sound at the end of a program. The
buzzer for a fault cannot be turned off.
Open the door.
Turn the dishwasher off with the
button.
Press and hold the Program button
and turn the dishwasher on...

Factory default
All settings can be reset to factory
default.
Open the door.
Turn the dishwasher off with the
button.
Press and hold the Program button
and turn the dishwasher on
simultaneouslyusing thebutton.
Keep the Program button pressed for
at least four seconds until the lower
right program indicator lights up.
If it does not come on, start over.
Press the Program button briefly 12
times.
The Intake/Drain indicator flashes
once long and twice short.The sequence of flashing by the upper
right...

Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
The dishwasher
does not start.The door is not properly
closed.Push the door firmly shut.
The machine is not
plugged in.Insert the plug.
The circuit breaker has
tripped.Reset the circuit breaker
(see the data plate for minimum
amperage).
The dishwasher is not...

Faults in the water intake/water drain
Problem Possible fault Solution
The dishwasher
stops shortly after
the program starts.
The buzzer sounds.
The Intake/Drain
indicator flashes and
lights up alternately
when the door is
open.The water supply valve
is closed.–Open the water supply valve
all the way.
The dishwasher has
stopped.
The buzzer sounds.
The Intake/Drain
indicator flashes
when the door is
open.Before fixing the fault:
– Turn the dishwasher off with
thebutton.
Fault in the water intake. – Open...

General problems with the dishwasher
Problem Possible fault Solution
The display is dark
and only the 
indicator lights.The indicator lights go out
automatically to save
energy (Standby).Press any button (except
) to come out of Standby
mode.
Detergent residue is
left in the dispenser at
the end of a program.The dispenser was damp
when detergent was added.Dry the dispenser before
adding detergent.
The detergent
dispenser lid cannot
be closed properly.Detergent residue is
blocking the catch.Remove the...

Sounds
Problem Possible fault Solution
There is a knocking
noise in the wash
cabinetThe spray arm is hitting an
item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
There is a rattling
noise in the wash
cabinetItems are not secure in the
wash cabinet.Interrupt the program, and
rearrange loose pieces.
A foreign object (e.g. a
cherry stone) has become
lodged in the drain pump.Remove the foreign object
from the drain pump (see
Cleaning the drain pump
and non-return valve)
There...

Poor cleaning results
Problem Possible fault Solution
The dishes are not
clean.The dishes were not loaded
correctly.See Loading the
dishwasher.
The program was not
powerful enough.Select a more intensive
program (see Program
Guide).
Not enough detergent was
dispensed.Use more detergent, or
change the detergent.
The spray arms are blocked. Turn the spray arms and
rearrange the dishes if
necessary.
The triple filter in the wash
cabinet is clogged or not
correctly inserted.
The spray arm jets might be...

Problem Possible fault Solution
Dishes are not dry,
glasses and
cutlery are
spotted.The rinse aid setting may be
too low, or the rinse aid
reservoir is empty.Increase the dosage, refill
the reservoir or switch the
rinse aid product when
refilling (see Rinse aid).
Dishes were taken out too
soon.Leave dishes in longer (see
Use).
A Tab product was used.
These products have a low
drying effect.Change the detergent, or
refill the rinse aid (see Rinse
aid).
White residue is
visible on cutlery
and dishes....