Miele G 2732 Operating Instructions

							External water softener
If the dishwasher is connected to an
external water softener unit which is
regenerated with salt, the water
hardness must still be set in the
dishwasher. Set the dishwasher to the
water hardness of your water softener
unit (see Before using for the first
time).
Set the dishwasher to the water
hardness of the external water
softener and confirm with OK.
Rinse aid
For best results the rinse aid dosage
can be adjusted.
The dosage can be set between 0 and
6 ml.
The dosage set by default to 3 ml of
rinse aid per program.
– Use a higher setting if spots appear
on dry glassware.
–
Use a lower setting if streaking
appears on dishes or glasses.

Select the desired rinse aid amount
and confirm with OK.
Filter checkh
This selection allows you to set the
number of cycles run before the filter
check message shows.
You can select between 30 and 60
cycles.
The filter check message is set by
default to 40 cycles.
Select the desired number of cycles
and confirm with OK.
See Cleaning and Care - Triple filter
system for more information.
Adjust Sensor Wash
The Sensor Wash program can be
adjusted to clean stubborn but normal
soiling.
Select
Yesand confirm with OK .
Settings
41
 
						

							Reorganize program listk
The order of the programs in the
program list can be reorganized. The
three most frequently used programs
can be saved to the first three
positions.
bBack-
k1. Normal
2. China & Crystal
Select from the first three programs
the one, which you would like
removed from the top three..
Confirm with OK.
bEconomy
jStarch/Cheese
SaniWash
Select the program to be saved to
the position of the previously
selected program.

Confirm with OK.
The reorganizing is confirmed and the
new order of programs is shown.
bBack-
k1. Starch/Cheese
2. China & Crystal
Reorganize another program or
switch back to Settings with
Back.
Save optionsÖ
Additional options can be selected for
some programs, e.g. extended drying.
See Use - Selecting options.
Save optionsallows you to save the
selected options for future use of the
program.
This function is turned off by default.
Select the desired setting and
confirm with OK.
Settings
42
 
						

							Child Safety LockX
The Child Safety Lock protects the
dishwasher from misuse.
If the dishwasher is turned on while the
Child Safety Lock is activated, the
display showsX
Machine locked.
The lock must be deactivated before
the dishwasher can be used.
As long as the Child Safety Lock is
activated, the dishwasher is locked
every time it is turned on.
The function is turned off by default.
Select
Onand confirm with OK.
Unlocking the dishwasher
Turn the dishwasher on.
The message
Machine lockedshows.
Press the OK button.
Child Safety Lock
Cancel?
YesNo

SelectYesand confirm with OK.
The dishwasher is unlocked and ready
to use.
Temperature|
The temperature can be displayed in
°C/Celsius or °F/Fahrenheit.
The temperatures are shown in
°C/Celsius by default.
Select the desired temperature unit
and confirm with OK.
Settings
43
 
						

							BuzzerO
When the buzzer is activated, a tone
sounds at the end of a program and if a
fault occurs.
The buzzer at the end of a program is
turned on by default.
Buzzer at the end of a program
The buzzer at the end of a program
sounds five times in intervals with a brief
break in between. The buzzer sounds up
to one hour if the dishwasher in not
turned off.
Buzzer in case of a fault
The buzzer for a fault sounds
continuously. The buzzer sounds up to
two minutes if the dishwasher is not
turned off or the fault is fixed.
The buzzer for a fault cannot be set
to off.Buzzer volume
Two buzzer volumes can be selected or
the buzzer can be turned off.
Off
The buzzer tone at the end of a
program is turned off.
Soft
The tone sounds in a soft volume.
Loud
The tone sounds in a loud volume.
Select the desired volume or
deactivate the buzzer.
Confirm with OK.
Settings
44
 
						

							Button tone
A tone will sound when a button is
pressed.
The volume can be set to seventeen
different levels. It is set to level 8 by
default.
Select the desired setting and
confirm with OK.
Brightness
The display brightness can be adjusted
in 17 levels.
The brightness is set to level 9 by
default.
Select the desired brightness and
confirm with OK.
Contrast
The display contrast can be adjusted in
17 levels.
The contrast is set to level 9 by default.

Select the desired contrast and
confirm with OK.
MemoryV
The memory function allows you to save
the last selected program.
When turning the dishwasher off and on
again after a program has finished or
opening and closing the door, the last
selected program is displayed instead
of the main menu.
The function is turned on by default.
Select the desired option and confirm
with OK.
Settings
45
 
						

							Dealer=
Demo modes are only for
showrooms.
The dishwasher has three demo
programs for showrooms.
The programs Demo mode and
Endless demo mode show the use
and function range of the dishwasher.
–
Demo mode:
The program is started by pressing
any button. It runs once and must be
started again.
–
Endless demo mode:
The program starts as soon as it is
activated and runs in a loop until it is
turned off.
–
Demo wash sound:
The program activates the pumps to
demonstrate the wash sound.
–
Trade show mode:
Once the machine is used for the
first time this option is disabled in the
display.Turning the demo mode on
Select the desired option.
Confirm the following messages with
OK.
Press any button to start the selected
demo mode.
To cancel the demo mode press any
button again and confirm with OK.
Turning the demo mode off
Select
Offand confirm with OK .
The display changes into the menu
Settings.
Factory default{
All settings can be reset to the factory
default.
Select
Resetand confirm with OK.
Leaving the Settings menu

SelectBackand confirm with OK.
The display changes to the program
menu.
Settings
46
 
						

							With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
Technical faults
Problem Possible fault Solution
After the dishwasher was
turned on with	, the
display stays off and the
Start indicator does not
flash.The machine is not
plugged in.Insert the plug.
The fuse has
tripped.Reset the circuit breaker.
See data plate for minimum
amperage.
The dishwasher stops
during a program.The fuse has
tripped.Reset the circuit breaker.
See data plate for minimum
amperage.
The buzzer sounds.
The display shows the
following:
Technical fault FXX
Call Technical Service
There may be a
technical fault.Turn the dishwasher off	.
After a few seconds:
– Turn the dishwasher on.
– Select the desired program
with the program selection
buttons.
–
Press the Start button.
If the problem persists, call
Technical Service.
The buzzer sounds.
The display shows the
following:
Fault
Waterproof F70
Close water faucet
The waterproof
system has
activated.–
Turn off the water supply.
–
Contact Miele Technical
Service.
Frequently asked questions
47
 
						

							Problems water intake/drain
Problem Possible fault Solution
The buzzer sounds.
The display shows the
following:
Water intake
Open water faucetThe water supply is
closed.Open the water supply all the
way.
Fault
Water intake FXXBefore fixing the fault:
–Turn the dishwasher off	.
Fault F12/F13:
Fault in the water
intake.–Open the water supply all the
way and restart the program.
– Clean the water intake filter,
see User Maintenance
Instructions.
– The water pressure at the
water connection is lower
than 4.35 psi. Consult a
plumber.
Frequently asked questions
48
 
						

							Issue Possible fault Solution
The buzzer sounds. The
program Energy Saver
displays the fault:
Water intake temp. too low
The intake water does not
have a minimum
temperature of 115°F
(45°C). See Plumbing -
Connection to the water
supply.–Restart the program.
–If the fault is displayed
again use a different
program.
The buzzer sounds. The
display shows the
following:
Fault FXX
Drain
Before fixing the fault:
–Turn the dishwasher
off	.
Fault F11: Fault in the
water drain. There might
be water in the wash
cabinet.–Clean the triple filter.
–Clean the drain pump
and the non-return
valve.
See User Maintenance
Instructions for more
information on the above.
– Remove any kinks in
the drain hose.
Frequently asked questions
49
 
						

							General problems with the dishwasher
Issue Possible fault Solution
The display remains
off.The display and the
program selector go
into Standby mode to
save energy.Press any button.
The display shows the
following:
Middle spray arm blocked
or
Lower spray arm blocked
The middle or lower
spray arm is blocked
by dishware.Open the dishwasher door
and rearrange items blocking
the spray arms.
The spray arm jets of
the middle or lower
spray arm are clogged.–Turn the dishwasher off	.
Then:
–Clean the spray arms. See
User Maintenance
Instructions.
Frequently asked questions
50