Miele G 1173 Scvi Operating Instructions

							The Miele waterproof anti-leak
system
Providing your dishwasher has been
installed correctly, the Miele waterproof
anti-leak system will protect you from
water damage throughout its lifetime.
Connection to the water
supply
,Water in the dishwasher must
not be used as drinking water.
–The dishwasher may be connected
to a cold or hot water supply, max.
60 °C. We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply all programme stages
which would otherwise be carried out
with cold water will be carried out
with hot water.
,A warm water connection with
temperatures exceeding 60 °C may
cause damage to the unit and affect
the product guarantee.
–
The inlet hose is approx. 1.5 m long.
A 1.5 metre long flexible metal
extension hose, pressure tested to
14,000 kPa/ 140 bar, is available as
an optional accessory if required.
–
A stopcock with a
3/4 male thread
must be provided on site.–The dishwasher is constructed to
comply with Australian regulations,
and may be connected to a suitable
supply without an extra non-return
valve if national regulations allow
this.
–The water pressure (flow pressure at
the take-off point) must be between
30 and 1000 kPa (0.3 and 10 bar).
If the water pressure is too high, a
pressure reducer valve must be
fitted.
,To avoid any damage to the
appliance, the dishwasher must only
be connected to a fully vented
plumbing system.
Plumbing
61
 
						

							!The inlet hose mustnotbe
shortened or damaged in any way
as it contains electrical components
(see illustration).
This appliance incorporates back
-
flow protection complying with
AS/NZS 3500.1.2. No further
backflow protection required for
connection to the water supply.
Plumbing
62
 
						

							Drainage
–The appliance drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
–The dishwasher is supplied with
approx. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
–The drain hose can be extended
using a connection piece to attach a
further length of hose.
The drainage length must not be
longer than 4 m, and the delivery
head must not exceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied (see installation
diagram).
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector
protrudes too far into the drain hose,
it will need to be shortened.
Otherwise the drain hose may
become blocked.
–
The drain hose must not be
shortened.
,Make sure that there are no
kinks in the hose, and that it is not
squashed or stretched.Venting the drainage system
If the on-site drain connection is
situated lower than the guide path for
the bottom basket rollers in the open
door, the drainage system must be
vented. Otherwise a siphoning effect
during a programme can cause the
appliance to empty itself of water.
To vent it:
^Open the dishwasher door fully.
^
Pull the lower spray arm firmly
upwards to remove it.
^
Cut off the top of the vent valve in the
wash cabinet.
Plumbing
63
 
						

							Dishwasher model G 1XXX G 2XXX
Height 80.5 cm
(adjustable + 6.5 cm)84.5 cm
(adjustable + 6.5 cm)
Height of building-in
recessMin. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm)
Width 59.8 cm 59.8 cm
Width of building-in
recess60 cm 60 cm
Depth 57 cm 57 cm
Weight Max. 55 kg Max. 61 kg
Voltage 230 V 230 V
Connected load 2300 W 2300 W
Fuse rating 10 A 10 A
Test marks Electrical safety, Typetest
Mark, C-Tick MarkElectrical safety, Typetest
Mark, C-Tick Mark
Electrically suppressed
according toAS/NZS 1044 AS/NZS 1044
Water pressure (flow rate) 30 - 1000 kPa
(0.3 - 10 bar)30 - 1000 kPa
(0.3 - 10 bar)
Hot water connection Up to max. 60 °C Up to max. 60 °C
Delivery head Max. 1 m Max. 1 m
Drainage length Max. 4 m Max. 4 m
Mains cable Approx. 1.7 m Approx. 1.7 m
Capacity 12 place settings 14/12 place settings*
* depending on model
Technical data
64
 
						

							65
 
						

							66
 
						

							67
 
						

							Alteration rights reserved/
G1173/G2173/ 1608M.-Nr. 07 223 570 / 00