Miele G 1173 Scvi Operating Instructions

							To clean the inside of the filter, the flap
must be opened:
^Press catchesatogether in the
direction of the arrows as shown,
and open the filterb.
^Rinse all the filters under running
water.
^Then close the flap so that the catch
engages.^Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
^Then turn the handle clockwise to
lock the filter combination in place.
,Take care when you are fitting
the filter combination that it is
secured in position correctly.
Otherwise coarse soil could get into
the circulation system and cause a
blockage.
Cleaning and care
41
 
						

							Cleaning the spray arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected
and cleaned regularly (approx. every
4 - 6 months).
^Switch the dishwasher off.
Remove the spray arms as follows:
^Take out the cutlery tray (if your
dishwasher is fitted with one).
^Push thetopspray arm upwards to
engage the inner ratchet. Then
unscrew the spray arm.
^
Push themiddlespray arms upwards
ato engage the ratchet. Then
unscrew the spray armb.^Remove the lower basket.
^Pull thelowerspray arm firmly
upwards to remove it.
^
Use a pointed object to push food
particles into the spray arm jets.
^
Rinse thoroughly under running
water.
^
Replace the spray arms and check
that they rotate freely.
Cleaning and care
42
 
						

							With the aid of the following guide, minor problems can be easily corrected
without calling in a Miele service technician, saving you both time and money.
,Repairs should only be carried out by a suitably qualified and trained
person in strict accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage the
appliance. The manufacturer cannot be held liable for unauthorised work.
Technical problems
Problem Possible cause Remedy
The appliance does
not start.The door is not properly
closed.Push the door firmly shut.
The appliance is not
plugged in.Insert the plug and switch on
at the socket.
The fuse is defective or
has tripped.Reset or replace the fuse.
(Minimum fuse rating - see
data plate).
The appliance is not
switched on.Press the On buttonU, and
select a programme.
The dishwasher
stops during a
programme.The fuse is defective or
has tripped.Reset or replace the fuse.
Problem solving guide
43
 
						

							Problem Possible cause Remedy
The buzzer sounds.
All the programme
indicators flash when
the door is opened.There may be a
technical fault.Clean the water inlet filter
and clean the drain pump
and non-return valve as
described in “Maintenance”.
If this does not resolve the
problem,
–switch the dishwasher off
with the Off buttonV.
After a few seconds:
–Switch the dishwasher
back on.
–Select the programme
required with the
programme selector
button;?.
– Close the door.
If the indicator lights flash
again, there is a technical
fault.
– Call the Service
Department.
The drain pump works
even when the door is
open.The Waterproof system
has reacted.– Close the stopcock.
–
Call the Service
Department.
Problem solving guide
44
 
						

							The dishwasher does not fill/drain.
Problem Possible cause Remedy
The dishwasher
stops working
shortly after the start
of the programme.
The buzzer sounds.
The Inlet/drain check
light2/2flashes
when the door is
opened.The stopcock is
closed.–Open the stopcock fully.
The dishwasher
stops during a
programme.
The buzzer sounds.
The Inlet/drain check
light2/2flashes
when the door is
opened.Before rectifying the problem you
must:
– Switch the dishwasher off with the
Off buttonV.
Water intake is
restricted.– Open the stopcock fully.
– Clean the water inlet filter (see
Maintenance).
– The water pressure at the intake is
lower than 30 kPa (0.3 bar).
Seek professional advice.
Water outlet is
restricted, water
remains in the
wash cabinet at
the end of a
programme.– Clean the filter combination. See
Cleaning and care.
–
Clean the drain pump. See
Maintenance.
–
Clean the non-return valve. See
Maintenance.
–
Remove any kink in the drain
hose.
Problem solving guide
45
 
						

							General problems
Problem Possible cause Remedy
Detergent residue is
left in the dispenser at
the end of a
programme.The dispenser was still
damp when detergent was
added.Make sure the dispenser is
dry before adding
detergent.
The detergent
dispenser lid cannot
be closed properly.Clogged detergent residue
is blocking the catch.Clean the detergent from
the catch.
At the end of a
programme there is a
film of moisture on
the inside of the door
and the interior walls.This is caused by the
drying system and does not
indicate a fault.The moisture will dissipate
after a short while.
Water remains in the
wash cabinet at the
end of a programme.Before rectifying the
problem you must:
– Switch the dishwasher
off with the Off button
V.
The filter combination in the
wash cabinet is clogged.Clean the filter
combination. See
Cleaning and care.
The drain pump or
non-return valve may be
blocked.Clean the drain pump or
the non-return valve. See
Maintenance.
The drain hose is kinked. Remove any kink from the
drain hose.
Problem solving guide
46
 
						

							Noises
Problem Possible cause Remedy
Knocking noise in the
wash cabinet.A spray arm is knocking
against an item in a
basket.Interrupt the programme,
and rearrange the items
which are obstructing the
spray arm.
Rattling noise in the
wash cabinet.Items of crockery are
insecure in the wash
cabinet.Interrupt the programme,
and rearrange the items of
crockery.
Knocking noise in the
water pipes.This may be caused by
the on-site installation or
the cross-section of the
piping.This has no influence on
dishwasher function. If in
doubt, contact a suitably
qualified plumber.
Problem solving guide
47
 
						

							Unsatisfactory washing result
Problem Possible cause Remedy
The dishes are not
clean.The dishes were not loaded
correctly.See notes in Loading the
dishwasher
The programme was not
powerful enough.Select a more intensive
programme. See Programme
chart.
Not enough detergent was
dispensed.Use more detergent, or
change your detergent.
Items are blocking the path
of the spray arms.Rearrange the items so that
the spray arms can rotate
freely.
The filter combination in the
base of the wash cabinet is
not clean or is not correctly
fitted. This may cause the
spray arm jets to get
blocked.Clean and/or fit the filter
combination correctly. Clean
the spray arm jets. See
Cleaning and care.
The non-return valve is open
and blocked. Dirty water has
flowed back into the wash
cabinet.Clean the drain pump and
the non-return valve. See
Maintenance - Cleaning the
drain pump and non-return
valve.
Smearing appears
on glassware and
cutlery, there is a
bluish sheen on
the surface of
glassware; film can
be wiped off.The rinsing agent dosage is
set too high.Reduce the dosage. See
Before using for the first
time - Rinse aid.
Problem solving guide
48
 
						

							Problem Possible cause Remedy
Dishes, cutlery
and glasses are
not dry or are
flecked.The amount of rinse aid
may be insufficient, or the
rinse aid reservoir empty.Replenish the reservoir,
increase the dosage or
change the brand of rinse aid.
See Before using for the first
time.
Crockery was taken out of
the cabinet too soon.Leave it in for longer. See
Operation.
White residue is
visible on cutlery
and crockery,
clouding occurs
on glassware; film
can be wiped off.Not enough rinse aid was
used.Increase the dosage. See
Before using for the first time
- Rinse aid.
There is no salt in the salt
reservoir.Fill the salt reservoir. See
Before using for the first time
- Filling the salt reservoir.
The salt reservoir cap has
not been screwed on
correctly.Replace it, making sure that it
screws back on correctly.
An unsuitable combination
detergent has been used.Change your detergent. Use a
standard liquid, tablet or
powder detergent.
The water softener is
programmed to a setting
which is too low.Select a higher water softener
setting. See Before using for
the first time.
Problem solving guide
49
 
						

							Problem Possible cause Remedy
Glassware has a
brown or blue tinge,
and film cannot be
wiped off.This may be caused by the
detergent.Change your detergent.
Glassware is dull and
discoloured; film
cannot be wiped off.The glasses are not
dishwasher-proof. The
surfaces are affected.There is no remedy.
Purchase glassware which
is dishwasher-proof.
Tea or lipstick stains
have not been
completely removed.The wash temperature of
the selected programme
was too low.Select a programme with a
higher wash temperature.
The bleaching effect of the
detergent used is too low.Change your detergent.
Plastic items are
discoloured.Natural dyes e.g. from
carrots, tomatoes or
ketchup may be the cause.
The amount of detergent
used or its bleaching effect
was not sufficient to deal
with natural dyes.Use more detergent. See
Operation.
Discolouration is irreversi-
ble.
There are rust stains
on cutlery.The affected items are not
corrosion resistant.There is no remedy.
Purchase cutlery which is
dishwasher-proof.
A programme was not run
after dishwasher salt was
added. Traces of salt have
got into the wash cycle.Always run the Quick wash
programme, without any
crockery in the dishwasher
and without selecting the
Turbo function (if present),
after adding dishwasher
salt.
The salt reservoir cap has
not been screwed on
correctly.Replace it, making sure
that it screws back on
correctly.
Problem solving guide
50