Miele Fn 14827 Operating And Installation Instructions

^Then separate retaining plateffrom
covere, by pushing it slightly to the
left and then pulling the cover
forwards and off.
^Rotate retaining platefby 180°.
^Then fit coverefrom the front over
retaining platef, and slide it over to
the right. The writing must be visible.
^Remove coverg, rotate it by 180°
and fit it to the opposite side.
^Then fit coveretogether with
retaining platefon the opposite
side.
^
Remove caphfrom the bearing
bush in the door and refit on the
opposite side.
Changing the door...

Changing over the hinge brackets
Important! The height of the door
on stainless steel appliances can
be adjusted.
Please read the relevant
instructions.
The instructions are the same for
all appliances from Fitting the
appliance door.
A. White appliances
(door not height adjustable)
^
Pull hinge pinatogether with discb
and adjustable footcupwards and
off.
^
Remove cover capd.
^
Undo screwseand take hinge plate
foff.
^
Unscrew partifrom hinge platef,
rotate it by 180° and refit into the hole
on the...

^Unscrew partifrom hinge plateg,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^Refit cover capein the other hole.
^Unscrew threaded pindfully using
the allen key supplied.
^Fit the threaded pindinto hinge
plate on the opposite side, until it is
flush with the hinge plate.
^The end must protrude sufficiently
through the hinge pin hole such that
the guide on the hinge pin will fit over
it later on (see following illustration).
^Remove coverh.
^Unscrew and remove...

To refit the door
^Place the door onto hinge pincfrom
above.
^Close the door.
^Fit hinge plateconto the opposite
side and secure it with screwsd.
^Fit coversaandbto their opposite
sides.
^Align the door with the appliance
housing using the outer long slots in
the lower hinge plate. Then tighten
the screws.Replacing the soft-close door
mechanism
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Insert the soft-close mechanism back
into the door, starting at the right
hand...

The screw holes on the left and right
must line up perfectly.
^First fix the soft-close mechanism
onto the appliance side, then onto
the handle sidec, pushing it firmly
towards the appliance.
^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^
Remove retaining...

Refitting the handle
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
tighten both grub screwsawith a
suitable allen key until mounting plate
clines up...

The appliance door can be aligned to
the housing using the outer long slots in
the lower hinge plate.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
^Remove centre screwafrom the
hinge plate.
^Slightly loosen both outer screwsb.
^Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.
Aligning the appliance door
57
 

aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work...

59
 

Alteration rights reserved / 2811
FN 14827 S, FN 14827 S ed/csM.-Nr. 09 171 890 / 00