Miele F 5122 Ui Operating And Installation Instructions

With abuilding under height of
820 mmthe plinth height can be set
between100 - 170 mm.
With a plinth height of exactly 100 mm,
the plinth can be fitted without altering
it.
With a height >100 mma cutout for
ventilation must be provided in the
plinth (see "Appliance installation").
Abuilding under height of 870 mmis
obtained by adjusting the appliance
feet. This increases the height of the
plinth, which, in this case, can be150 -
220 mm.
With a plinth height of exactly 150 mm,
the plinth can be...

Before installing the appliance decide
on the door hinging. If left hand door
hinging is required follow the
instructions below.
Unscrew the hingesat the top and
bottom of the door and the
appliance.

Fit the screwsloosely into the
opposite side.

Refit the hinges on the diagonally
opposite side of the door and then
tighten them.

Refit the appliance door onto
pre-fitted screws, then tighten the
screws.

Fit the covers suppliedinto the
holes.
Changing the door hinging
32
 

Weight of the furniture door
Before fitting a furniture door, ensure
that the weight of the door does not
exceed the maximum permitted:
ApplianceMaximum weight of
furniture door in kg
F 5122 Ui 19 kg
Fitting a door which is heavier than
the maximum permitted could
damage the hinges.
Preparing the appliance

Bend both fixing tabs at the top of the
appliance forwards as far as they will
go.
Installation
Position the power supply cable
so that it can easily be connected to
the electricity supply after...

Increase the height of the appliance
using the adjustable feet until the top
of the appliance lies directly under
the worktop (A).
To increase the height
– of thefront screw feetturn them
anti-clockwisewith a suitable
spanner.
–
of therear left screw footinsert the
hex nut supplied into the opening at
the front of the applianceand
using a hex spanner turn it
anti-clockwise.
–
of therear right screw footinsert
the hex nut supplied into the opening
at the front of the applianceand
using a hex spanner...

Fitting the plinth facing
To ensure trouble-free operation of
the appliance it is essential to fit the
original Miele ventilation grille.
Remove ventilation grilleby
pressing the clips in the openings
upwardsand simultaneously
pulling the grille forwards.
The plinth facingcan be fitted
without being altered in the following
situations:
It can be fitted unchanged if the
following dimensions are present:
Building-under
height
A
[mm]Plinth facing
height
b
[mm]
820 100
870 150
The height of the plinth...

Position the plinth facing along the
run of kitchen units.

Mark the protruding sectionAon the
ventilation grille consolewith a
pencil, then take the plinth facing
off again.

Cut protruding sectionAoff the
ventilation grille console.If the front slat on the facing does not
align with the front edge of the plinth
facing, cut off another slat.
Use pliers to remove the vertical ribs
.

Shorten the ventilation grille supports
by dimension A
(= ventilation grille console
overhang).

Secure the...

Fitting a furniture door
If there are no pre-drilled holes in the
furniture door, holes have to be drilled
as shown on the following drawing:
Drilling positions on framed doorsRemove screwsfrom the
underside of the appliance door.
Use the screws to secure both
bracketsto the underside of the
appliance door. The brackets must
be flush with the exterior of the
appliance door.
Shorten the brackets if necessary.
Installing the appliance
37
 

Unscrew adjuster stripfrom the
appliance door and use the screws
supplied to secure it to the furniture
door.
Loosen the adjusting screwson
the appliance door until there is a
gap of 4.0 mm (see detail).
Use the adjusting strip to hang the
furniture door onto adjusting screws
.

Secure the furniture door at the top
using screws.

Secure the furniture door at the
bottom using the screws supplied
fitted through the bracket. Use the
washerssupplied.
Aligning the furniture door
Align the...

39
 

Alteration rights reserved / 2611
F 5122 UiM.-Nr. 09 087 950 / 00