Miele F 123 Ui Operating And Installation Instructions

With abuilding under height of
820 mmthe plinth height can be set
between100 - 170 mm.
With a height >100 mma cutout for
ventilation must be provided in the
plinth (see Appliance installation).
Abuilding under height of 870 mmis
obtained by adjusting the appliance
feet. This increases the height of the
plinth, which, in this case, can be150 -
220 mm.
With a height >150 mma cutout for
ventilation must be provided in the
plinth (see Appliance installation).A furniture front panel is required for
installing...

Before installing the appliance decide
on the door hinging. If left hand door
hinging is required follow the
instructions below.
^Remove stoppersa.
^Unscrew the hingesbat the top and
bottom of the door and the
appliance.
^
Fit the screwscloosely into the
opposite side.
^
Refit the hinges on the diagonally
opposite side of the door and then
tighten them.
^
Refit the appliance door onto
pre-fitted screwsc, then tighten the
screws.
^
Plug the holes with the stoppersa.
Changing the door hinging
32
 

Preparing the appliance
^Bend both fixing tabs at the top of the
appliance forwards as far as they will
go.
Installation
^
Position the power supply cablea
so that it can easily be connected to
the electricity supply after the
appliance has been built in.
^
Push the appliance into the nicheb
until the front edge of the hinge
aligns with the front edge of the
furniture housing unit (marked X on
the drawing).
Make sure that the mains cable doesnot get trapped when the appliance
is pushed into the niche....

^Use the screws suppliedato secure
the appliance to the worktop.
Fitting the plinth
To ensure trouble-free operation of
the appliance it is essential to fit the
original Miele ventilation grille.
^Remove ventilation grillebby
pressing down the two lugsaand
simultaneously pulling the grille
forwards.
The plinth facingccan be fitted
without being altered in the following
situations:
It can be fitted unchanged if the
following dimensions are present:
Building-under
height
A
[mm]Plinth facing
height
b
[mm]...

The height of the plinth facing has to
be altered in the following
circumtances:
If the building-under heightA = 820
mmand the plinth facing heightbis
greater than 100 mma cut-out has to
be made in the plinth facing.
This also applies to a building-under
heightA = 870 mmand plinth facing
heightb greater than 150 mm.
Building-under
height A [mm]Dimension H
[mm]
820
870100
150
^Position the plinth facing along the
run of kitchen unitsa.
^
Mark the protruding sectionAon the
ventilation grille bracketawith...

^If the front slat on the facing does not
align with the front edge of the plinth
facing, cut off another slata.
^Use pliers to remove the vertical ribs
b.
^
Shorten the ventilation grill supports
bby dimension A
(= ventilation grille bracket
overhang).
^
Secure the plinth facing to the run of
kitchen unitsa.
^
Push the ventilation grille onto the
bracketc.
Fitting a furniture door
If there are no pre-drilled holes in the
furniture door, holes have to be drilled
as shown on the following drawing:...

^Remove screwsafrom the
underside of the appliance door.
^Use the screws to secure both
bracketsbto the underside of the
appliance door. The brackets must
be flush with the exterior of the
appliance door.
^Shorten the brackets if necessary.^Screw adjuster stripato the
furniture door.
^Loosen the adjusting screwsbuntil
there is a gap of 3.5 mm (see detail).
^Hang the furniture door onto
adjusting screwsb.
^Secure the furniture door at the top
using screwsc.
^
Secure the furniture door at the
bottom using...

Aligning the furniture door
^Align the furniture door with
neighbouring furniture doors:
–
Height adjustment Yis made by
turning the upper and lower
adjusting screws .a.
–
Side adjustments Xare made by
moving the furniture door to the left
or right.
–
Depth adjustments Zare made by
gently shifting the furniture door
forwards or backwards.^First tighten the top adjusting screws
aandb, then the lower screwsc.
^Finally replace coversdande.
Installing the appliance
38
 

39
 

Alteration rights reserved / 2509
F 123 Ui-2M.-Nr. 07 371 640 / 01