Miele Da2894 Manual

							If the power level indicators 1 and 4
flash the automatic switch back is not
activated.
^To activate the automatic switch back
press the + button.
The power level indicators 1 and 4
light continuously.
^To save the setting press the Delay
Shut Down button.
If the procedure is not stored within
4 minutes of programming, the hood
will automatically default to the old
data.Fan performance
The maximum air flow capacity is
625 cfm. Factors such as narrow duct
diameter and bends will affect this
value.
Level 1 operates at 40% capacity
Level 2 operates at 60% capacity
Level 3 operates at 80% capacity
Level 4 operates at 100% capacity
Operation
11 
						

							Delayed Shut Down
If odors or smoke remain in the kitchen
after cooking has been completed, the
Delayed Shut Down feature can be
selected to allow the hood to continue
running for either 5 or 15 minutes.
^Press the Delayed Shut Down button
while the fan is still running.
Press once = 5 minute delay
(left indicator lights)
Press twice = 15 minute delay
(right indicator lights)
To cancel the Delayed Shut Down
feature press the button again.
Turning off the fan
^Press the On/Off button to turn the
fan off.
The indicator goes out.
Automatic Safety Shut Off
The fan will turn off automatically 10
hours after the last button was activated.
The lighting however will remain on.
^Press the On/Off button to turn the
fan back on again.
Operation
12 
						

							Turning the lighting on/off
The overhead lighting can be turned on
and off independently of the fan.
^Press the light buttonbrieflyto turn
on the lighting.
The light button indicator illuminates.
^Press the light buttonbrieflyagain to
turn off the lighting.
The light button indicator will go out.
Dimming the lighting
The brightness of the lighting can be
adjusted.
^While the lighting is turned on, press
the light button.
The lighting will dim until the button is
released.
^If the button is pressed again, the
lighting will brighten until the button is
released.
If the button is pressed continuously,
the light will cycle between bright and
dark.
^Press the light button again to turn off
the lighting.
Operation
13 
						

							Grease filter timer
A timer monitors the hours of fan
operation. The indicator for the grease
filter will light after 30 hours of
operation. The grease filter and air
intake panel must then be cleaned.
After the grease filter has been cleaned
and put in place, the grease filter timer
must be reset.
^To do this, press the grease filter
button for about 3 seconds.
The indicator will go out.Checking the grease filter timer
To check the percentage of time
already used:
^Press the On/Off button to turn the
fan on.
^Press the grease filter button.
The number of flashing –/+ indicators
show the percentage of programmed
hours that have been used.
1 indicator = less than 25 %
2 indicators = less than 50 %
3 indicators = less than 75 %
4 indicators = less than 100 %
This information will remain stored in
memory in the event of a power failure.
Operation
14 
						

							Reprogramming the grease filter
timer
The grease filter timer is preset to 30
hours. This time can be lengthened or
shortened to 20, 30, 40 or 50 hours.
–A time of 20 hours should be
programmed in kitchens with
frequent pan or deep frying.
–A time of 20 hours should also be
programmed if the kitchen is only
used occasionally to prevent grease
which has accumulated over a long
period of time from hardening on the
filters, making cleaning more difficult.
^Press the On/Off button to turn off the
fan.
^
Press the Delayed Shut Down and
grease filter buttons at the same time.The indicator for the grease filter and
one of the –/+ indicators will flash.
The lit –/+ indicator shows the
programmed time:
1st indicator from the left = 20 hours
2nd indicator from the left = 30 hours
3rd indicator from the left = 40 hours
4th indicator from the left = 50 hours
^Use the –/+ button to select the
desired time.
^Store the selection by pressing the
grease filter button.
If the procedure is not stored within
4 minutes of programming the hood
will automatically default to the old
data.
Operation
15 
						

							Before cleaning or servicing the
hood, disconnect it from the power
supply by either removing the fuse,
unplugging it from the outlet or
manually tripping the circuit
breaker.
Cleaning the casing
,Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
willdamage the surface.
^The air intake panel, exterior surfaces
and controls can be cleaned with
warm water and liquid dish soap
applied with a soft sponge.
^Wipe dry using a soft cloth.
Only use a slightly damp sponge
when cleaning the controls. Water
could penetrate into the electronics
and cause damage.
^
Glass surfaces can be cleaned using
glass cleaner.
Avoid:
–
cleaning agents containing soda,
acids or chlorides,
–
abrasive cleaning agents
e.g. powder or cream cleansers,
–
abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents,
–
limescale removers.
These will damage the surface.Stainless steel
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
Stainless steel colored controls
These controls may become dis
-
colored or damaged if not cleaned
regularly.
Do not use a stainless steel cleaner
on these controls.
Cleaning and care
16 
						

							Grease filter and air intake
panel
The reusable metal grease filter
removes solid particles from the vented
kitchen air (grease, dust, etc).
The grease filter and the air intake
panel should be cleaned every 3 - 4
weeks or whenever the grease filter
indicator lights.
Keep the grease filter clean to
prevent a fire hazard.Removing the air intake panel
^To remove the air intake panel gently
pull out and downward, shifting the
lower part a bit to the right. Lift it out
of the latches.
Support the air intake panel so that it
does not fall onto the cooktop.
Removing the grease filter
^
To remove the grease filter, pull on
the lever.  Support the grease filter so
that it does not fall onto the cooktop.
Cleaning and care
17 
						

							Cleaning the grease filters
^By hand:use a scrub brush with a
solution of warm water and mild
detergent.
Do not use the pure detergent,
aggessive all purpose cleaners, oven
sprays or limescale removers. They
could destroy the filters.
^In a dishwasher:place the filters
vertically in the lower basket, making
sure that the spray arm is not
blocked.
Use a hot temperature program, e.g.
Heavy Soil or Pots and pans.
Use the recommended amount of
dishwasher detergent. Overuse could
destroy the filter.
Depending on the detergent,
cleaning the grease filter in a
dishwasher may cause permanent
discoloration of the filter surface.
Performance of the filter will not be
affected by this discoloration.
^
After cleaning, the filter can be
placed on a towel to air dry.
^
Clean the air intake panel according
to Cleaning the casing.
^
While the filter and the air intake
panel are removed, clean any dirt or
grease from the interior casing to
prevent the risk of fire.^Push the grease filter back in place.
^Hook the air intake panel on the
latches and push a little to the left.
Push it toward the unit so that it clicks
in place.
^After returning the grease filter, press
the grease filter button for 3 seconds
to reset the timer.
The indicator light will go out.
^If the grease filter and air intake
panel are cleanedbeforethe grease
filter timer has reached its maximum,
the grease filter button should be
pressed for 6 seconds to reset the
counter to zero.
Cleaning and care
18 
						

							Changing the light bulbs
Before changing the light bulbs,
disconnect the hood from the power
supply by either removing the fuse,
unplugging it, or manually tripping
the circuit breaker.
When in use halogen bulbs become
extremely hot, and they can burn
your hands. Do not attempt to
change the bulbs until they have
had sufficient time to cool.
Do not touch the bulb surface.
Fingerprints or body oils deposited
on the bulb will decrease its life.
Please follow the bulb
manufacturer’s instructions.^Pull the old bulb out of its socket
using the enclosed lever. Replace it
with a new one. Be careful not to
drop the bulb on the cooktop.
Replacement bulbs may be ordered
from Miele’s Technical Service
Department.
See the phone numbers on the back
of this booklet.
Cleaning and care
19 
						

							Repairs
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department at
the phone number on the back of this
booklet.
^When contacting the Technical
Service Department, please quote
the model and serial number of your
appliance.
These are shown on the data plate
which is visible when the grease filter is
removed.
MieleCare
(only USA)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
appliance investment is covered by
5 years of worry free ownership.
MieleCareis the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more aboutMieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
www.store.miele.com
After Sales Service
20