Miele Cs12121 Manual

							Safety features31System lockThe system lock can only be activatedif all the cooking zones are switchedoff.
Your hob is equipped with a systemlock to prevent the cooking zones beingswitched on inadvertently.If a power level is selected when thesystem lock is activated, 0007 appears inthe display for approx. 3 seconds.Activating
000ETurn the (outer) right cooking zonecontrol anti-clockwise to the point ofresistance and hold it until 0007 appearsin the display.
Deactivating
000ETurn the (outer) right cooking zonecontrol anti-clockwise to the point ofresistance and hold it until 0007 goes outin the display.
Safety switch-offThe safety switch-off mechanism istriggered automatically if one of thecooking zones is heated for an unusu-ally long period of time. This period oftime depends on the power level selec-ted. Once exceeded, the cooking zoneswitches off and 0008 and 000F flash altern-ately in the cooking zone display. Thecooking zone can be operated againafter it has been switched off and backon. 
						

							Safety features32Overheating protectionAll the induction coils and cooling ele-ments for the electronics are fitted withan overheating protection mechanism.Before the induction coils or coolingelements get too hot, the overheatingprotection mechanism cuts in in one ofthe following ways:
–Any Booster function in operation willbe switched off.–The set power level will be reduced.–The cooking zone will switch offautomatically. 000B will flash in the cook-ing zone display.–Further cooking zones switch offautomatically.000ESwitch off the affected cooking zone.If the cooking zone is not switched off,0008 and 000F will flash alternately in thecooking zone display.
You can use the cooking zones again asusual when the fault code has gone out.
The overheating protection mechanismcan be triggered by:–heating up an empty pan.–fat or oil being heated on a highpower level.–insufficient ventilation to the under-side of the hob.–a hot cooking zone being switchedon after an interruption to the powersupply.
If, despite removing the cause, theoverheating protection mechanism trig-gers again, contact Miele. 
						

							Cleaning and care33Danger of burning.The cooking zones must be switchedoff. The hob must have cooled down.Danger of injury.The steam from a steam cleaning ap-pliance could reach electrical com-ponents and cause a short circuit.Do not use a steam cleaner to cleanthe hob.
The use of unsuitable cleaningagents can cause the surfaces todiscolour or alter.All surfaces are susceptible toscratching.Remove any cleaning agent residuesimmediately.
Allow the CombiSet to cool downbefore cleaning.000EThe CombiSet and accessoriesshould be cleaned after each use.000EDry the CombiSet after using water toclean it. This helps prevent limescaledeposits.
Unsuitable cleaning agentsTo avoid damaging the surfaces of yourappliance, do not use:
–washing-up liquid,–cleaning agents containing soda, al-kalines, ammonia, acids or chlorides,–cleaning agents containing descalingagents,–stain or rust removers,–abrasive cleaning agents, e.g.powder cleaners and cream cleaners,–solvent-based cleaning agents,–dishwasher cleaner,–grill and oven cleaners,–glass cleaning agents,–hard, abrasive brushes or sponges,e.g. pot scourers, or sponges whichhave been previously used with ab-rasive cleaning agents,
–melamine eraser blocks. 
						

							Cleaning and care34Ceramic surfaceDo not clean the area between theglass-ceramic surface and the frameor the frame and the worktop withsharp, pointed objects.This could damage to the seals.
Do not use washing-up liquid toclean the appliance as washing-up li-quid will not remove all soiling anddeposits.It will form an invisible coating whichwill cause permanent discolourationof the ceramic surface.Clean the hob regularly with a suit-able ceramic hob cleaning agent.
Wipe all coarse soiling off using a dampcloth. Stubborn soiling may need to beremoved with a shielded scraper blade.Then clean the hob with Miele ceramicand stainless steel hob cleaner (see"Optional accessories") or a suitableproprietary ceramic hob cleaning agentapplied with kitchen paper or a cleancloth. Do not apply cleaner whilst thehob is still hot, as this could result inmarking. Please follow the manufac-turer's instructions.Finally wipe the hob with a damp cloth,then dry with a soft, dry cloth. Residuescan burn onto the appliance the nexttime it is used and cause damage to theceramic surface. Ensure that all clean-ing agent residues are removed.Spots caused by limescale, water andaluminium residues (spots with a metal-lic appearance) can be removed usingMiele's ceramic and stainless steel hobcleaner.
Danger of burning.Protect your hands with oven glovesbefore using a shielded scraperblade to remove sugar, plastic or alu-minium residues from the hot hob.Should any sugar, plastic or alu-minium foil spill or fall onto a hot cook-ing zone while it is in use, first switch offthe appliance. Then carefully scrape offall the sugar, plastic or aluminiumresidues from the hob immediatelywhilst they are still hot, using a shieldedscraper blade. Allow the appliance tocool down, and then clean as describedabove. 
						

							Cleaning and care35Stainless steel frame/controlpanel000EClean the frame and the control panelwith a solution of warm water and alittle washing-up liquid applied with asoft sponge.
You can also use a ceramic and stain-less steel cleaning agent. We recom-mend also using a stainless steel condi-tioning agent to help prevent resoiling(see "Optional accessories).
Do not use ceramic and stainlesssteel cleaner or stainless steel condi-tioning agent on the printing.This would rub the printing off.These areas should be only cleanedwith a solution of warm water and alittle washing-up liquid applied with asoft sponge.
Operating controls
000EClean the control(s) with a solution ofwarm water and a little washing-up li-quid applied with a soft sponge.Stubborn soiling should be soakedfirst.
000EDry the control(s) with a clean cloth. 
						

							What to do if ...36With the aid of the following guide, minor problems can be easily correctedwithout contacting Miele.If having followed the suggestions below, you still cannot resolve the problem,please contact Miele (see end of this booklet for contact details).
Danger of injury. Installation, maintenance and repairs may only be carriedout by a suitably qualified and competent person. Repairs and other work by unqualified persons could be dangerous. Miele can-not be held liable for unauthorised work.Do not attempt to open the casing of the CombiSet yourself.
ProblemCause and remedyThe cooking zones donot heat up.There is no power to the hob.000ECheck if the mains fuse has tripped. If it has, con-tact a qualified electrician or Miele (minimum fuserating - see data plate).There may be a technical fault.
000ETurn the cooking zone control to 0.000EDisconnect the appliance from the electricity sup-ply for approx. 1 minute. To do this:–switch off at the isolator, or–disconnect the mains fuse.000EIf, after resetting the trip switch in the mains fusebox and switching the appliance back on, the ap-pliance will still not heat up, contact a qualifiedelectrician or Miele.
A smell and vapours aregiven off when the newappliance is being used.The metal components have a protective coating.When the appliance is used for the first time, thiscauses a smell and possibly also vapour. The materialfrom which the induction coils are made also gives offa smell in the first few hours of operation. This smellwill be less noticeable with each subsequent use be-fore dissipating completely. The smell and any vapourgiven off do not indicate a faulty connection or appli-ance and they are not hazardous to health.
0004 is flashing in a cook-ing zone display.There is no pan on the cooking zone, or the pan is un-suitable.000EUse a suitable pan (see "Pans"). 
						

							What to do if ...37ProblemCause and remedy0008 flashes alternatelywith the power level in acooking zone display.The power level set has been reduced because theBooster function on the linked cooking zone hasbeen activated (see "Booster").0008 flashes alternatelywith 000F in a cooking zonedisplay. The cookingzone has switched offautomatically.
There has been no pan, or an unsuitable pan, on thecooking zone for more than 3 minutes.000EUse pans that are suitable for induction (see"Pans") or switch off the cooking zone if it is nolonger needed.
The overheating protection mechanism has been ac-tivated.
000ESee "Overheating protection".
TwinBooster level II has been activated on the linkedcooking zone.
000B appears in the cook-ing zone display.The overheating protection mechanism has been ac-tivated.000ESee "Overheating protection".0007 appears in the displayfor several secondsafter a cooking zonehas been switched on.
The system lock has been activated.000EYou need to deactivate the system lock (see "Sys-tem lock").0010 appears in the displayfor several secondsafter a cooking zonehas been switched on.The cooking zone doesnot heat up.
Demonstration mode is activated.000ETurn the right-hand (outer) cooking zone controltwice briefly anti-clockwise to the point of resist-ance then once again, holding it for approx.3 seconds. 
						

							Optional accessories38Miele offer a comprehensive range ofuseful accessories as well as cleaningand conditioning products for yourMiele appliances.These products can be ordered throughthe Miele Webshop.These can also be ordered from Miele(see end of this booklet for contact de-tails) or from your Miele dealer.
Ceramic and stainless steelhob cleaner 250 ml
Removes heavy soiling, limescale de-posits and aluminium residuesStainless steel conditioningagent 250 mlRemoves water marks, flecks and fingerprints. Helps keep the appliance lookinggood for longer.
Microfibre cloth
Removes finger marks and light soiling    
						

							Safety instructions for installation39The CombiSet must only be installed and connected to the electricity sup-ply by a suitably qualified and competent person in strict accordance with cur-rent national and local safety regulations.Fit the wall units and cooker hood before fitting the CombiSet to avoid dam-aging it.00010002The veneer or laminate coatings of worktops (or adjacent kitchenunits) must be treated with 100 °C heat-resistant adhesive which willnot dissolve or distort. Any backmoulds must be of heat-resistantmaterial.
00010002The CombiSet must not be installed over a fridge, fridge-freezer,freezer, dishwasher, washing machine, washer-dryer or tumble dryer.00010002This CombiSet must not be installed above an oven unless it hasa built-in cooling fan.00010002The electrical cable of the CombiSet must not come into contactwith any moving kitchen component (e.g. a drawer) or be subject toany mechanical action which could damage it.
00010002Observe carefully the safety clearances listed on the followingpages.All dimensions are given in mm. 
						

							Safety distances40Safety distance above theCombiSet
A minimum safety distance must bemaintained between the CombiSet andthe cooker hood above it. See thecooker hood manufacturer's operatingand installation instructions for details.If the manufacturer's instructions arenot available for the cooker hood a min-imum safety distance of at least760 mm must be maintained, or if anyflammable objects (e.g. utensil rails,wall units etc) are installed above theCombiSet, a minimum safety distanceof at least 760 mm must be maintainedbetween them and the CombiSet be-low.
When two or more CombiSets whichhave different safety distances areinstalled together below a cookerhood, you should observe thegreatest safety distance.