Midway Touch Master 8000 Upright Conversion Manual

Touchmaster® Conversion Kit    Setup - 9 
10. POWER:  
Loosen, but do not remove, top six screws on power supply terminal strip by turning one full 
turn with a screwdriver. Do not loosen bottom two (AC) screws.  
11.  Remove DC wires from +5, GND, -5, and +12 terminals. Leave AC wires connected. If you must 
disconnect a green and yellow striped AC connector to reach another connector, replace it. 
SURGE 
PROTECTOR 
(not on all 
models)
Leave AC 
and FG 
wires 
attached.
 
REMOVAL OF DC WIRES FROM...

Setup - 10  Midway Amusement Games, LLC 
INSTALL GAME ELECTRONICS 
1. 
ORIENT ELECTRONICS:  Place Touchmaster® CPU Board Assembly and metal tray on wooden 
electronics shelf in roughly same position as previous electronics so heat sink is at rear of cabinet. 
2.  Using screws in parts kit, attach metal tray onto wooden electronics shelf. Do not overtighten screws. 
3. 
ADJUST VOLUME:  Set master volume control to middle position. The potentiometer is near heat 
sink. Use a screwdriver to point arrow...

Touchmaster® Conversion Kit    Setup - 11 
5. TOUCHSCREEN:  
Connect Touchscreen Connector Cable to bottom of new Touchscreen Controller. 
6. MOUNTING:  
Orient new Controller in same position as previous Controller (if applicable) and mount 
in cabinet 
If there was no Touchscreen Controller before, install hook and loop fastener material from parts kit. 
LED should face front of cabinet. 
7. GROUND WIRE:  
If there was an existing ground wire, attach it to threaded stud on metal plate. Use 
nut in...

Setup - 12  Midway Amusement Games, LLC 
MASTER VOLUME
CONTROLHEAT SINK
TOUCHSCREEN
CONTROLLER
CONNECTOR CABLE
 
CPU BOARD ASSEMBLY 
16. VIDEO:  
Attach video connector to monitor board. Orient yellow and red-striped wire in connector 
where existing red wire was previously oriented, as noted in electronics removal section of manual. 
17. GROUND WIRE:  
Reconnect any additional ground wires removed during disassembly. 
VERIFY NEW EQUIPMENT OPERATION 
1. START UP:  
Plug in line cord and turn on AC power....

Touchmaster® Conversion Kit    Setup - 13 
 
LOCATION OF DECALS
 
4. LABEL:  
Locate the epilepsy warning label. Peel off backing and apply to the base of the cabinet just 
underneath the monitor bezel. 
5. CURRENCY:  
Insert coins and play games to verify operation. Record number of coins used. 
6.  Remove the cash door and confirm that coin meter has advanced for each coin inserted. 
7. OPTIMIZE:  
Read operating instructions and adjust game characteristics.  
8. MARQUEE
:  Remove screws holding...

Setup - 14  Midway Amusement Games, LLC 
INVERTING TOUCHSCREEN SIGNALS 
1.  Turn off AC power and unplug line cord. 
2.  Unlock and remove Bottom Door and pull wooden electronics shelf out slightly. 
3.  Locate P2 connector on CPU 
Board Assembly and remove 
connector from socket. 
 
CONNECTOR P2 ON CPU BOARD ASSEMBLY 
4.  Using your fingers, pry off 
plastic connector cap. Set 
cap aside in a safe place. 
 
REMOVAL OF CONNECTOR CAP 
5.  Remove first wire (it will be 
blue with a white stripe). 
Replace...

TOUCHMASTER
®
 
CONVERSION 
CHAPTER 
 
OPERATION 
 
NOTICE: Information in this manual is subject to change without notice. Midway 
Amusement Games, LLC reserves the right to make improvements in equipment 
function, design, or components as progress in engineering or manufacturing methods 
may warrant. Field installed upgrade kits may also change the operating sequence or 
functions.
 
 
NOTICE:  You are responsible for enforcing all local, state, and federal regulations 
concerning this game.
 
123
54
2 

System - 2  Midway Amusement Games, LLC 
GAME FEATURES 
Touchmaster® offers many different games, each of which accommodates one or two players. Update 
software frequently to offer players new games and interesting updates to existing games. 
You can adjust game characteristics to suit player proficiency. Modify graphics to alter game appearance. 
Increase or decrease game speed and length, etc. This flexibility increases game entertainment value for 
frequent players and lets you maximize revenues....

Touchmaster® Conversion Kit    System - 3 
TOUCHMASTER® OPERATION 
STARTING UP 
Each time AC power is turned on or power is restored, code executes from the boot ROM. These self-
diagnostic tests automatically verify and report hardware and EPROM conditions. If any individual test fails 
an error message for that test displays for three seconds or until an on-screen button is touched. If a fatal 
error (i.e., a touchscreen controller fault) is detected, the message remains on the screen until the fault...

System - 4  Midway Amusement Games, LLC 
MENU SYSTEM 
SYSTEM OVERVIEW 
Adjustments and diagnostics appear in a series of on-screen menus. The SYSTEM SETUP menu lets you 
enter information, make changes, or verify equipment operation. Subsequent screens displays one 
specific group of choices. The detail menu presents data or runs the required test. You must be at the 
detail menu level to detect errors, make changes, or activate tests. Both the operator controls and the 
player controls are used to move...