Metz Talio 32 S Lcd Operating Instructions

91
ProblemPossible causeRemedy
TV set does not react
to commands from
the remote control• No line of sight between the
remote control and the TV set.
• Sunlight is shining directly on
the infrared window of the TV
set.
• Batteries of the remote control
are exhausted.
• TV set has been switched off
with the main power switch.
• Fault in the internal processor.• Remove any obstacles
between the units.
• Prevent sunlight from
shining on the set.
• Replace the batteries.
• Switch on the TV set
with the main...

92
Data Logic does not
work.• The Data Logic video recorder
with data transfer has not been
registered correctly.
• The Scart cable does not have
all pins connected through.• Open the menu AV
devices and register
the Data Logic video
recorder as video recor-
der 1 with Data Logic
On.
• Use a Scart cable in
which all pins are con-
nected through.
ProblemPossible causeRemedy
General problems
with an external AV
device connected to
the TV set.• The AV device has not been
registered in the TV set.• Open the...

93
Calling the menu
MENU
The settings of the satellite antenna system must
be entered in the menu Configuration so that
the TV set knows them.
These settings should always be made in the order
in which they are shown in the right-hand column
of the menu, starting at the bottom, i.e. LNB sup-
ply voltage, DiSEqC system, etc..
LNB supply voltage
The LNB voltages for selection of the polarisation
(horizontal H = 18V, vertical V = 14V) are alrea-
dy set and do not normally need to be changed.
If the cable to...

DiSEqC makes it possible to control the satel-
lite antenna digitally via the existing antenna
cable and is a prerequisite for the reception of
signals from more than two satellites (e.g.
Astra, Eutelsat, Hotbird).
If you wish to receive signals from at least three
satellites (e.g. ASTRA 19.2°, Eutelsat 16°, Hot-
bird 13°) the antenna system can be controlled
only with the aid of DiSEqC.
This menu item is not available in a 2**
menu.
Switching DiSEqC on and of
f
• Press the MENU key to open the TV
menu....

You can set up to four satellites in the menu Con-
figuration. No satellite is set in the factory.
The LNB frequency is used to switch between the
high and low frequency bands. The default fre-
quencies Low band 9.75 GHzand High band
10.60 GHzare set in the factory.
Selecting satellites
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration.
• Press the appropriate numeric key (in this exam-
ple 
to select DVB-S.
• Press the appropriate numeric key (in
this...

Before executing a DVB station search, you must
make the appropriate search settings.
Depending on the features installed in the TV set
and your personal requirements, you can make
the following settings:
All = search for all stations on the selected satelli-
te.
FTA only = search only for unencrypted (free-to-
air) stations on the selected satellite.
FTA (CI) = search for all FTA stations and stations
which can be received with the CI
module. 
The menu item FTA (CI) is available
only if a CI module has...

DVB-S station search
The DVB-S station search scans the entire reception band
for TVand radio stationsand stores them in separate TV
and radio station tables. For details of the DVB radio
mode, see Section 29 in the operating instructions for the
TV set.
If you are not satisfied with the order in which the stations
are stored, you can move stations to other positions in the
table or delete them. For further details, see Section 24,
Sorting stations in the operating instructions for the TV
set.
The...

For the manual search, you must know the fre-
quency, the symbol rate and the polarisation of
the station for which you want to search.
Executing the manual search
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration
• Press the appropriate numeric key (in this exam-
ple 
to select DVB-S.
• The cursor is located on the line LNB supply
voltage.
• Press the appropriate numeric key (in
this example 
 to select Manual
search.
• The cursor then moves to Satellite....

With the menu item, General settings, you can
specify whether or not the data are to be saved in
the non-volatile memory of the TV set when trans-
mission parameters are changed.
This update function applies to stations which use
different transmission parameters at different times
of the day, such as when they transmit regional
programmes.
Setting the data update function
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration.
• Press the appropriate numeric key...

Automatic station search . . . . . . . . . . . . . 55-59
Automatic zoom . . . . . . . . . . . . . . . . . . . . . . 30
AV devices, connecting/registering . . . . . . . . 63
AV devices, removing . . . . . . . . . . . . . . . . . . 68
AV programme position . . . . . . . . . . . . . . . . 16
AV playback, devices with switching voltage .  15
AV  
playback, devices without switching voltage. 16
Batteries for the remote control. . . . . . . . . . . . . 6
Brightness . . . . . . . . . . . . . . . . . . . . . . ....