Metz Milos 37s Operating Instructions
Have a look at the manual Metz Milos 37s Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 5 Metz manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
91 ProblemPossible causeRemedy TV set does not react to commands from the remote control• No line of sight between the remote control and the TV set. • Sunlight is shining directly on the infrared window of the TV set. • Batteries of the remote control are exhausted. • TV set has been switched off with the main power switch. • Fault in the internal processor.• Remove any obstacles between the units. • Prevent sunlight from shining on the set. • Replace the batteries. • Switch on the TV set with the main power switch. • Switch off the TV set with the main power switch, wait a few seconds and then switch it on again. The message Enter code is displayed when the TV set is switched on.• The childlock is active and was programmed to disable all stations.• Enter the code you used when programming the childlock. The TV set will not switch to a selected programme position. A teddy bear is dis- played instead.• The childlock is active and was programmed so that only the stations shown in the list beside the teddy bear may be selec- ted.• Enter the code you used when programming the childlock. You have switched off the TV set with the key, but the green LED remains on.• EPG data are currently being collected from the programmed EPG station.• None. When all data have been collected, the TV set will switch itself off automatically. Direct recording of an analogue terrestrial station (received via roof antenna or cable) with Data Logic does not work.• The Data Logic video recorder is not connected to the roof antenna or cable outlet with a suitable cable.• Connect the Data Logic video recorder to the roof antenna or cable outlet with a suitable cable.
92 Data Logic does not work.• The Data Logic video recorder with data transfer has not been registered correctly. • The Scart cable does not have all pins connected through.• Open the menu AV devices and register the Data Logic video recorder as video recor- der 1 with Data Logic On. • Use a Scart cable in which all pins are con- nected through. ProblemPossible causeRemedy General problems with an external AV device connected to the TV set.• The AV device has not been registered in the TV set.• Open the menu AV devices, select the devi- ce with the cursor, set the signal types (OUT/IN) correctly and press the OK key. Make sure that you con- nect the AV device as shown in the connection diagram. A film in 16:9 format is played back from an AV device, but is displayed in 4:3 for- mat.• The picture format for this pro- gramme position has not been set correctly in the TV menu.• Select the AV program- me position and set the picture format to 16:9 or Automatic (see Sec- tion 37). The menu of a con- nected AV device (such as a DVD play- er) is not visible on the TV screen.• The AV device has been regis- tered in the TV menu with the signal type Composite video.• Register the AV device with the signal type RGB (see page 68).
93 Calling the menu MENU The settings of the satellite antenna system must be entered in the menu Configuration so that the TV set knows them. These settings should always be made in the order in which they are shown in the right-hand column of the menu, starting at the bottom, i.e. LNB sup- ply voltage, DiSEqC system, etc.. LNB supply voltage The LNB voltages for selection of the polarisation (horizontal H = 18V, vertical V = 14V) are alrea- dy set and do not normally need to be changed. If the cable to the satellite antenna is very long, the voltages reaching the LNB may be too low. In such cases, the volta- ges can be increased by 1 V by activa- ting the line-compensation function. If any changes should be necessary, they can be made as follows. Changing the settings • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Press the appropriate numeric key (in this example to select DVB-S. • Press the OK key and, in the setting window, use the -+ key to switch the LNB supply voltage on or off. • Press the Ok key to confirm the new setting. • Press the EXIT key to close the TV menu. If the TV set is connected to a community antenna, the LNB supply voltage must always be set to Off. A1. Set-up of satellite system LNB supply voltage i General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating LNB supply voltage on Power compensation off Change with Accept value with F1➔ OK – + The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK EXIT
DiSEqC makes it possible to control the satel- lite antenna digitally via the existing antenna cable and is a prerequisite for the reception of signals from more than two satellites (e.g. Astra, Eutelsat, Hotbird). If you wish to receive signals from at least three satellites (e.g. ASTRA 19.2°, Eutelsat 16°, Hot- bird 13°) the antenna system can be controlled only with the aid of DiSEqC. This menu item is not available in a 2** menu. Switching DiSEqC on and of f • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Press the appropriate numeric key (in this example to select DVB-S. • Use the cursor control key to select DiSEqC system and press the OK key to confirm the selection. The cur- sor is now located in front of DiSEqC system in the setting window. • Use the -+ to select Yes or No. • Press the OK key to confirm the new setting. • Press the EXIT key to close the TV menu. 94 A1.1 Set-up of satellite system DiSEqC system i Calling the menu MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK EXIT General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating DiSEqC system on Change with Accept value with F1➔ OK – +
You can set up to four satellites in the menu Con- figuration. No satellite is set in the factory. The LNB frequency is used to switch between the high and low frequency bands. The default fre- quencies Low band 9.75 GHzand High band 10.60 GHzare set in the factory. Selecting satellites • Press the MENU key to open the TV menu. • Press the red key to open the menu Confi- guration. • Press the appropriate numeric key (in this exam- ple to select DVB-S. • Press the appropriate numeric key (in this example to select Satellite A. • Use the -+ key to select the desired satellite. The most common satellites are displayed one after the other, together with the symbol rates for each one. Depending on the satellite, it may be necessary to set additional symbol ratesmanually if the selected satellite uses different symbol rates and you wish to find the related transponders in an automatic station search. • Use the cursor control key to select Low band or High band. The settings depend on the components installed in the satellite antenna. For the correct settings, please consult the data sheet or the label of the LNB(s) being used. • Press the OK key to confirm the new settings. • Press the EXIT key to close the TV menu. 95 Calling the menu A1.2 Set-up of satellite system Selecting satellites MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK EXIT General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating Satellite Astra 1 Symbol rate 1 22000 Low band 9,75 GHz Symbol rate 2 27500 High band10,60 GHz Symbol rate 3 - - - - -Change with the numeric keys or . Accept value with F1➔ OK– +
Before executing a DVB station search, you must make the appropriate search settings. Depending on the features installed in the TV set and your personal requirements, you can make the following settings: All = search for all stations on the selected satelli- te. FTA only = search only for unencrypted (free-to- air) stations on the selected satellite. FTA (CI) = search for all FTA stations and stations which can be received with the CI module. The menu item FTA (CI) is available only if a CI module has been installed and a CA module is plugged into it. Making the search settings • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Press the appropriate numeric key (in this example to select DVB-S. • Press the appropriate numeric key (in this example to select Search set- tings. • Use the -+ key to select the desired setting. • Press the Ok key to confirm the new setting. • Press the EXIT key to close the TV menu. 96 A2. Setting the stations Search settings Calling the menu MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK EXIT General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating Stations Free-to-air only Change with Accept value with F1➔ OK – +
DVB-S station search The DVB-S station search scans the entire reception band for TVand radio stationsand stores them in separate TV and radio station tables. For details of the DVB radio mode, see Section 29 in the operating instructions for the TV set. If you are not satisfied with the order in which the stations are stored, you can move stations to other positions in the table or delete them. For further details, see Section 24, Sorting stations in the operating instructions for the TV set. The station search will function correctly only if the LNB frequencies have been set and sto- red correctly. Executing the automatic station search • Press the MENU key to open the TV menu. • Press the red key to open the menu Configuration. • Press the appropriate numeric key (in this example to select DVB-S. • Press the appropriate numeric key (in this example to select Automatic search. • In the setting window, use the -+ key to select the desired satellite (if several are availa- ble; see Section 1.2 of the operating instructions for the TV set). • Use the cursor control key to move to the menu line Start station search. • Press the OK key to start the station search. The TV set searches for the specified stations and places them in a station table, which is then dis- played. If desired, you can sort or move stations to other positions in the table or delete unwanted stations. For details, see Section 24 of the operating instructions for the TV set.. 97 A2. Setting the stations Automatic search Calling the menu MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK EXIT General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating Satellite Astra1 Start station search Change with Accept value with F1➔ OK – +
For the manual search, you must know the fre- quency, the symbol rate and the polarisation of the station for which you want to search. Executing the manual search • Press the MENU key to open the TV menu. • Press the red key to open the menu Confi- guration • Press the appropriate numeric key (in this exam- ple to select DVB-S. • The cursor is located on the line LNB supply voltage. • Press the appropriate numeric key (in this example to select Manual search. • The cursor then moves to Satellite. If more than one satellite is available, use the -+ key to select the desired satellite. • In the setting window, use the cursor control key to select the menu line Frequency. • Use the numeric keys or the -+ key to set the frequency. • In the setting window, use the cursor control key to select the line Polarisation and use the -+ key to select H=Horizontal or V=Vertical. • In the setting window, use the cursor control key to select the line Symbol rates and enter the symbol rate with the numeric keys. • In the setting window, use the cursor control key to select the line Start station search and press the OK key to start the search. The station is placed in the station table. If des- ired, you can sort or move stations to other posi- tions in the table or delete unwanted stations. For details, see Section 24 of the operating instructions for the TV set. 98 A2. Setting the stations Manual search Calling the menu MENU The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. OK General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating Satellit Astra1 Frequency 11836 MHz Symbol rates 27500 Polarisation H Start station searchChange with Accept value with F1➔ OK – +
With the menu item, General settings, you can specify whether or not the data are to be saved in the non-volatile memory of the TV set when trans- mission parameters are changed. This update function applies to stations which use different transmission parameters at different times of the day, such as when they transmit regional programmes. Setting the data update function • Press the MENU key to open the TV menu. • Press the red key to open the menu Confi- guration. • Press the appropriate numeric key (in this example to select DVB-S. • The cursor is located on the line LNB supply voltage. • Press the appropriate numeric key (in this example to select General set- tings. • In the setting window, use the -+ key to set Update data to On. • Press the OK key to confirm the new setting. • Press the EXIT key to close the TV menu. 99 Calling the menu A2. Setting the stations Updating the data The number of subjects and sections depends on the selected scope of operation. Depending on the configuration of the TV set, the various menu items may be displayed in a different order and numbered differently. MENU OK EXIT General settings Manuall search Automatic search Search settings Satellite D Satellite C Satellite B Astra 1 DiSEqC system LNB supply voltage Function for F2 Function for F1 EURO sockets DVB-C DVB-T DVB-S Analog-TV Country Language Operating Update data on Change with Accept value with F1➔ OK – +
Automatic station search . . . . . . . . . . . . . 55-59 Automatic zoom . . . . . . . . . . . . . . . . . . . . . . 30 AV devices, connecting/registering . . . . . . . . 63 AV devices, removing . . . . . . . . . . . . . . . . . . 68 AV programme position . . . . . . . . . . . . . . . . 16 AV playback, devices with switching voltage . 15 AV playback, devices without switching voltage. 16 Batteries for the remote control. . . . . . . . . . . . . 6 Brightness . . . . . . . . . . . . . . . . . . . . . . . . . 7,18 Camcorder, connecting . . . . . . . . . . . . . . . 63,78 Childlock . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Childlock, activating . . . . . . . . . . . . . . . . . . . 31 Childlock, deactivating . . . . . . . . . . . . . . . . . 32 Childlock, permitted programmes. . . . . . . . . . 32 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Code for childlock. . . . . . . . . . . . . . . . . . . . . 32 Colour standard . . . . . . . . . . . . . . . . . . . 29,56 Connections on front and rear of set . . . . . 78,79 Copying recordings . . . . . . . . . . . . . . . . . . . 80 Country . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 DataLogic video recorder . . . . . . . . . . . . . . . 64 Decoder (D-Box), connecting . . . . . . . . . . . . . 63 Direct recording (OTR) . . . . . . . . . . . . . . . . . 41 Double font size . . . . . . . . . . . . . . . . . . . . . . 13 DVD player, connecting . . . . . . . . . . . . . . . . . 63 DVD player, removing . . . . . . . . . . . . . . . . . . 68 Electronic Programme Guide = EPG . . . . . . . . 46 EURO sockets . . . . . . . . . . . . . . . . . . . . . 15,79 External devices (playback) . . . . . . . . . . . . . . 15 External devices, connecting . . . . . . . . . . . 63,79 Font size, double . . . . . . . . . . . . . . . . . . . . . 13 Forced mono . . . . . . . . . . . . . . . . . . . . . . . . 27 Freeze frame . . . . . . . . . . . . . . . . . . . . . . . . . 7 Function keys . . . . . . . . . . . . . . . . . . . . . . . 7,44 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Headphones . . . . . . . . . . . . . . . . . . . . . . 77,78 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 HiFi output . . . . . . . . . . . . . . . . . . . . . . . 70,71 100 Index