Metz Milos 37s Operating Instructions

71
On the rear of the TV set, you will find audio
sockets and a digital audio-out socket (see page
79) which can be used to connect the TV set to a
HiFi system (HiFi amplifier).
If you wish to play back the sound only via a HiFi
system (HiFi amplifier) which is connected with the
aid of a Cinch cable, you must select the function
Sound via HiFi.
If you wish to play back the sound only via a HiFi
system (HiFi amplifier) which is connected with the
aid of an optical audio cable (Toslink, available
as an...

72
MENU

Opening the menu28. Display Configuration
This menu item is not available in a 2 **
menu.
The green digital display on the front of the TV set
can be programmed, as desired, to show the time
or the current programme position.
Setting the display configuration 2)
• Press the MENU key to open the TV menu.
• Press the red key ® to open the menu Configu-
ration.
• Use the cursor control key  to select Initial
programme position.
• Use the corresponding numeric key
(in the example: 
) to select...

73
29. DVB Radio Mode
To switch from TV mode to DVB radio mode, press
the R key.
The screen is automatically blanked after about
30 seconds.
To switch from DVB radio mode to TV mode, press
the TV key.
Setting DVB radio stations
The available DVB radio stations are automatical-
ly detected during a station search (see Section
22) and stored in a separate station table at the
operating level for radio mode.
The radio station table can be sorted (see Section
24) and the station logos can be changed (see...

74
The adjustable scope of operation for the TV set
can be a great help in finding your way around
the complex operating functions of the TV set.
The scope of operation can be set to various
levels, which are identified by asterisks.
1   
Just watching TV- in other words, it is
not possible to open the TV menu and
only the functions available on the
remote control can be used:
- Zapping
- Selection of programme positions with the nume-
ric keys, the oval P+/P- rocker key or the 
white key  .
- Opening...

75
• Use the - +key to select the desired scope of
operation and press the OK key to save the
new setting.
2    
This menu permits you to configure the
use of the TV set to a certain degree.
All of the functions listed for the 1
menu are available and are supple-
mented by the following functions:
- Childlock
- Timer control (sleep timer)
- Automatic station search
- Transfer of the TV station table from
the TV set to a Data Logic video recor-
der.
- Editing functions in the station table
3    
This is...

76
32. Connecting Headphones
31. Operation without the 
Remote Control
Operation without the remote control is provided
as an emergency measure in case the batteries of
your remote control are exhausted or the remote
control is not readily available.
The local controls are located on the bottom
edge of the TV set, on the right.
Switching on
Press the main power switch on the TV set. After
about five seconds, the TV set is switched on with
programme position 1 or the programmed initial
programme position...

77
When receiving a dual-language pro-
gramme, you can switch between the
two sound channels.
In TV mode, press and hold the yellow
key  until the sound function Sound
mode is selected.
Then use the 
-+
key to select Sound 1
or Sound 2.
34. Cleaning the TV Set
33. Sound 1, Sound 2
Headph. Vol.
Sound mode Cannel 2
Spatial
Spatial 
Sound mode Cannel 2
Balance 
Before cleaning the set, always switch it off with the mains switch!
Incorrect treatment and cleaning of the screen surface can cause irreparable...

78
Service socket for
use by your dealer
35. Connections on the Left Side of the Set 
( Headphone socket, diameter 3.5 mm 
 FBAS/Video in (e.g. digital camera or camcorder)
 Audio in   R/L (e.g. camcorder)
) S-VHS or. Y/C in (e.g. camcorder)
)
 
(
Antenna socket
 

35.1 Connections on the Rear of the Set
(covered by a flap)
Viewed from below
EURO sockets for connection of
external AV devices
Video and audio IN/OUT
With the aid of an optical audio cable (Toslink cable, available from your
dealer), the digital audio signal (AC3) provided by the TV set can be extracted
for external processing.
*) The sockets Digital audio IN and Digital audio OUT can be operated in loop-
through mode. To do this, open the menu AV devices and activate (x) the menu
item Activate TV...

80
36. Copying between AV Devices
Direct recording
Opening the menu
If you wish to copy a recording from one of the
AV devices connected to your TV set (such as a
DVD player) to another connected AV device (such
as a video recorder), you must do this by means
of a direct recording operation. In this case, the
signal arriving at one of the EURO sockets is redi-
rected to the other EURO socket, from where it
can be recorded.
Example: you have a DVD player and
a video recorder connected to
the EURO sockets...