Marantz Vp 15s1 DLp Projector User Manual

23
ENGLISH
NO SIGNAL VALID SIGNAL
ANY INPUTVIDEO or S-VIDEO COMPONENT
3(# )%.*
NTSC PAL/SECAM 480i/576i 480p/576p 480i/576i 480p/576p Other1080i/720p/
1080p/540p
HDMI CSC HDMI 1

–––– –– ––

CSC HDMI 2

–––– –– ––

Deep Color HDMI 1

–––– –– ––

Deep Color HDMI 2

–––– –– ––

Display Keystone
    
Scale–
   
Width–
   
Position H–
   
Position V–
   
Installation
    
OSD/Blanking Menu Position
    
Language
    
Status...

24
ENGLISH
This projector has menus that make setting and adjustment easy.1.
Press the MENUbutton. The MENU screen appears on the screen.
2.
Use the 3and 4buttons to select a menu (Picture Adjust, Fine Menu 1, Fine Menu 2, Input Signal,
RGB/HD Adjust, Display, OSD/Blanking, Config) and press the 2button.
For image mode selection, see “Picture Mode”.  (

P.24)
3.
Use the 3and 4buttons to select a menu item and press the 2button.
4.
Use the 3, 4, 1and 2buttons to make the setting or adjustment of the...

25
ENGLISH
–Gamma setting
To change the type of Gamma curve, set the Picture Mode (

p.24) to User (1 – 9). Select “Gamma”
from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or
Dynamic).
–Color Temp. (Color Temperature)
1 : Red comes out strong. Color temperature is about 5250 K.
2 : Red is mildly strong. Color temperature is about 5800 K.
3 : Normal. Color temperature is about 6500 K.
4 : Blue is mildly strong. Color temperature is about 7500 K.
5 : Blue comes...

26
ENGLISH
–Cinema
Auto : Automatically selects the cinema mode when a video signal is input. 
NTSC: 3-2 pull down, PAL: 2-2 pull down
Off : Pull-down processing is not performed.
–VCR Mode
On : A projector is forced into the intra-field only deinterlacing mode.
Off : A projector is used with external field memories and operates in the full set of deinterlacing
modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing
using 3:2 pulldown detection (2:2 pulldown for 625/50...

27
ENGLISH
Standard 1
Component 1
Component 2
S-Video
VideoAuto
Auto
Auto
Auto
RGB Auto
HDMI2 HDMI1 Auto
AutoPicture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.HDMI
Input Signal
NTSC(NTSC-3.58)
: Conventional analog broadcasting used
mainly in USA, Canada, Taiwan, Korea, and
Japan.
PAL(PAL-4.43)
: Conventional analog broadcasting used
mainly in United Kingdom and Germany.
SECAM
: Conventional analog broadcasting used
mainly in France and Russia.
480p
: Standard...

28
ENGLISH
–Keystone
Adjust trapezoid image to rectangle image.
–Scale
Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the
original size.
–Width
Reduces the image width without changing the image height. The width can be reduced to about 75%
the original size.
–Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal. 
–Instllation
Sets the installation mode...

29
ENGLISH
–Menu Position
OSD position is selected from 9 positions.
–Status Info.
Enable: Displays the current status of the projector for a set amount of time in the upper right-hand
corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or
other setting is changed.
Disable: Does not display Status Info.
–Power-OFF Confirm.
Disable:
Directly puts the projector on standby without displaying the confirmation message when power
is shut off from the  button on the remote...

30
ENGLISH
–Auto Power Off
When the auto power off feature is set to Enable, power
to the projector automatically shuts off if no signals are
received and no operations are performed for about 10
consecutive minutes. If 9 minutes pass without the
projector receiving any signals or being operated in
anyway, the below message appears on the screen.
About 1 minute after the message appears on the screen, power to the projector shuts off.
Note:
After the above message appears on the screen, pressing any...

31
ENGLISH
CAUTION:
•Do not touch the lamp and the lamp unit
carelessly. It is extremely hot. Wait at least
one hour for the lamp to cool down before
handling.
•Do not loosen any screws except for those
mentioned below.
•The lamp may break if handled improperly.
•Do not use other than a Marantz
replacement lamp unit.❖
How to replace the Lamp Unit
PREPARATION:
When replacing the lamp, turn off the power for
the projector. After the cooling fan stops,
disconnect the power cord and wait for one
hour until...

32
ENGLISH
3.
Wait at the least one hour for the lamp and
lamp unit to cool down.
4.
Read the caution and warning labels on the
unit.
Lamp cover
WARNINGTHIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
SERIAL NO.
CAUTION : HIGH PRESSURE LAMP 
MAY EXPLODED IF IMPROPERLY HANDLED. 
REFER SERVICING TO QUALIFIED SERVICE 
PERSONNEL.ATTENTION :  LA LAMPE SOUS 
HAUTE PRESSION PEUT SI...