Marantz Vp 11s2l DLP Projector User Manual

							18
ENGLISH
BASIC OPERATIONS
Press the ONbutton on the remote controller or the / Ibutton on the projector.
The ON indicator lights up.
Switch to the equipment connected to the projector.
Every time the INPUTbutton of the projector or the INPUT3button of the remote controller is pressed,
the input signal rotates in the order of COMPONENT 1 
➔COMPONENT 2 
➔S-VIDEO 
➔VIDEO 
➔RGB
➔HDMI 1 
➔HDMI 2. When the INPUT4button of the remote controller is pressed, the input signal
rotates in the opposite order. An input signal can also be directly selected by pressing one of the COMP.1,
COMP.2, S-VIDEO, VIDEO, RGB, HDMI 1and HDMI 2buttons on the remote control.
INPUT V-MUTE
ENTERMENU
ASPECTINFO.
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
STD DYN
I M
AG4
THTRCOMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1
BLANKING AUX 2IRIS LAMP
C.TEMP GAMMA
B1
OFF
B3
B2
Selecting the Input Signal Source
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
STD DYN G4
THTRCOMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1 AUX 2
ON
STANDBYIRIS LAMP
C.TEMP GAMMA
Turning on the Power
You can select 5 kinds of ASPECT mode using remote controller.
Pressing the ASPECTbutton on the remote control rotates the
aspect ratio in the order of FULL 
➔NORMAL 
➔ZOOM 
➔V-
STRETCH 
➔THROUGH, allowing you to select an aspect ratio.
An aspect ratio can also be directly selected by pressing one of
the FULL, NORMAL, ZOOMor THROUGHbuttons on the remote
controller. A selection can also be made from the menu. (

P.26)Selecting the Aspect Mode
INPUT V-MUTE
ENTERMENU
ASPECT
FULL CINEMA
VCR MODE
BLACK LEVEL
PATTERN
BLACK
NOR ZOOM THRUINFO.
I M
A
BLANKING
B1
OFF
B3
B2
714@6@@&/(
 
 
 
 
 .
 
 
						

							19
ENGLISH
•Press the ZOOMbutton, the NORMALbutton or the FULLbutton on the remote controller for the 4:3
aspect ratio video source.
•Press the FULLbutton on the remote controller for 16:9 aspect ratio video source, such as 1080i,
1035i, and 720p video systems.
•Use Zoom mode when projecting a 480i, 480p, 576i, or 576p squeezed image with a 2.35: 1 aspect
ratio.
•Use V-Stretch mode when projecting a 720p, 1080i, or 1080p squeezed image with a 2.35: 1 aspect
ratio.The Screen Images in a 16:9 screen❖
Original Source Image
❖
Full mode
The 16:9 squeezed image is displayed with the
correct aspect.❖
Normal mode
❖
Zoom mode
A 2.35:1 image is displayed in the entire screen.
This function is best used when a 480i, 480p, 576i,
or 576p squeezed image is input.
16 : 9  video source
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.
4 : 3  video source
❖
Through mode
Images are shown at the same resolution as RGB/video signals. ❖
V-Stretch mode
The 2.35:1 image is shown across the entire screen. The vertical component of the aspect ratio is
elongated in this case. This function is best used when a 720p, 1080i, or 1080p squeezed image is input.
714@6@@&/(
 
 
 
 
 .
 
 
						

							20
ENGLISH
•Press the ZOOMbutton, the NORMALbutton or the FULLbutton on the remote controller for the 4:3
aspect ratio video source.
•Press the FULLbutton on the remote controller for 16:9 aspect ratio video source, such as 1080i,
1035i, and 720p video systems.
•Use Zoom mode when projecting a 480i, 480p, 576i, or 576p squeezed image with a 2.35: 1 aspect
ratio.
•Use V-Stretch mode when projecting a 720p, 1080i, or 1080p squeezed image with a 2.35: 1 aspect
ratio.The Screen Images in a 4:3 screen❖
Original Source Image
❖
Full mode
The 16:9 squeezed image is displayed with the
correct aspect.❖
Normal mode
❖
Zoom mode
A 2.35:1 image is displayed in the entire screen.
This function is best used when a 480i, 480p,
576i, or 576p squeezed image is input.
16 : 9  video source
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.
4 : 3  video source
❖
Through mode
Images are shown at the same resolution as RGB/video signals.1.
Press the STANDBYbutton on the remote controller or the / Ibutton on the projector.
2.
The fan continues running for about 1 minute to internally cool the projector. In the meantime, the ON
indicator on the projector flashes a blue color and buttons on the projector and remote control are
irresponsive to touch. Once the fan stops, the ON indicator goes out and the STANDBY indicator
lights up a green color to indicate the projector is on standby.
Notes :
- Do not pull out the AC power cord until the projector turns in standby mode.
- Do not pull out the power cord suddenly in the state of “POWER ON. It can cause a breakdown.
- If the WARNING indicator lights up or blinks a yellow color, check that the fan has stopped then
unplug the AC power cord from its outlet.
- The projector will not be turned on if the ONbutton on the remote controller or the  / Ibutton on
the projector is pressed immediately after turning off.  Press the ONbutton on the remote controller
or / Ibutton on the projector after the projector turns into standby mode.
- When on standby, power to the projector is not OFF completely. If not planning to use the projector
for an extended period of time, unplug the AC power cord from AC power outlet as explained above.
C1 C2 S G1
H1 H2 V G2A1
A2 RGB G3
COMP.1 COMP.2 S-VIDEO USER
HDMI 1 HDMI 2 VIDEO
AUX 1 AUX 2
ON
STANDBYIRIS LAMP
C.TEMP GAMMA
To Turn off the Power❖
V-Stretch mode
The 2.35:1 image is shown across the entire screen. This function is best used when a 720p, 1080i, or
1080p squeezed image is input.
714@6@@&/(
 
 
 
 
 .
 
 
						

							21
ENGLISH
OPERATIONSMenu Structure
Main Menu
ItemMain Menu
Item Main Menu
Item
Component 1VideoRGB
Auto*480i/576i480p540p576p
720p1035i1080i1080p
Auto*480i/576i480p540p576p
720p1035i1080i1080p
Auto*NTSCPA LSECAM
RGB/HD AdjustMode
ReadjustResolution HResolution VPosition HPosition VPhaseClamp Position
Input Signal
Component 2
Auto*480i/576i480p540p576p
720p1035i1080i1080p
HDMI 1
Auto*480i/576i480p576p720p
1035i1080i1080p
HDMI 2
Auto*480i/576i480p576p720p
1035i1080i1080p
S-Video
Auto*NTSCPA LSECAM
Yes / No
Clamp Width25 0*
25 0*
0* 50
-50
0* 10
-10
Position HPosition V
0* 50
-50
0* 50
-50
0* 50
-50
0* 50
-50
0* 10
-10
P.27
Config. 
(Configuration)Auto Power OFF
Remote ControlTrigger 2 FullTrigger 2 NormalTrigger 2 ThroughTrigger 2 ZoomReset Lamp Life
Enable / Disable*
On* / Off
On* / Off
On* / Off On* / Off
Trigger 2 V-Stretch
On* / Off
Yes / No
Yes / No Wireless* / Wired
Reset All
P.30
DisplayKeystone
ScaleWidth
0* 25
-25
P.28
Menu Position
OSD/Blanking
Status Info. Enable* / DisablePower-OFF Confirm. Enable / Disable*Blanking Memory Off* / 1 / 2 / 3Blanking Top
0* 100Blanking BottomBlanking LeftBlanking Right0* 100
-100 0*-100 0*
0* 1000* 100
Language
English*DeutschFrançaisEspañolTop-L*To pTop-R
Installation
Front*RearF + Ceiling
R + Ceiling
Color Wheel
x 6x 5*x 4Auto*Memory1Memory2
Memory3
P.29
P.27
CSC HDMI 1Deep Color HDMI 2
Auto*RGBYPBPR 4:4:4
YPBPR 4:2:2
YCBCR 4:4:4
YCBCR 4:2:2
Auto*8bit10bit12bit
HDMI
CSC HDMI 2
Auto*RGBYPBPR 4:4:4
YPBPR 4:2:2
YCBCR 4:4:4
YCBCR 4:2:2
Deep Color HDMI 1
Auto*8bit10bit12bit
P.28
Picture Mode
TheaterMain Menu
Item
Default / 1* / 2 / 3
Default / 1* / 2 / 3
Default / 1* / 2 / 3
1* / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
StandardDynamicUser
Picture Adjust
1 / 2 / 3* / 4 / 5 / HB
Iris 1 / 2 / 3*Aspect
Full*NormalZoomV-StretchThrough
Gamma
ABCDE
TheaterStandardDynamic
Contrast
P.24Fine Menu 1
Noise ReductionR GainG Gain
P.26P.25
0* 50
-500* 50
Sharpness
0* 50
0* 50
-50
B Gain
0* 50
-50
R Bias
0* 50
-50
G Bias
0* 50
-50
B Bias
0* 50
-50
0* 50
-50
Fine Menu 2
Cinema
VCR ModeBlack LevelDuring HDMI input, “Expand” or “Normal*” is shown.FRCCEC
P.26
Auto* / Off
On / Off*
On / Off* 0 IRE* / 7.5 IRE
Auto 1* / Auto 2 / 60Hz / 50Hz / 48Hz
Luminance Gain
0* 50
-50
Picture Shift V
0* 50
Overscan
Enable* / Disable
-50
Chroma Delay
0* 5
-5
Brightness
0* 50
-50
Color
0* 50
-50
Tint
0* G10 R10
Color Temp.
Normal* / Economy
Lamp Mode
Center-RBottom-L
Center-L
Bottom
Center
Bottom-RPortuguêsItaliano
* Default setting
714@6@@&/(
 
 
 
 
 .
 
 
						

							22
ENGLISH
Functions by Signal
NO SIGNAL VALID SIGNAL
ANY INPUTVIDEO or S-VIDEO COMPONENT RGB HDMI
NTSC PAL/SECAM 480i/576i 480p/576p 480i/576i 480p/576p Other1080i/720p/
1080p/540p
Picture Mode Theater–
   
Standard–
   
Dynamic–
   
User–
   
Picture Adjust Gamma–*1 *1 *1 *1 *1 *1 *1 *1 *1
Contrast–*9 *9 *9 *9 *9 *9 *9 *9 *9
Brightness–*9 *9 *9 *9 *9 *9 *9 *9 *9
Color–*9 *9 *9 *9 *9–––*9
Tint–*9 *9 *9 *9 *9–––*9
Sharpness–*9 *9 *9 *9 *9 *9 *9 *9 *9
Color Temp.–*9 *9 *9 *9 *9 *9 *9 *9 *9
Lamp Mode–*9 *9 *9 *9 *9 *9 *9 *9 *9
Iris–*9 *9 *9 *9 *9 *9 *9 *9 *9
Fine Menu 1 Noise Reduction–*9 *9 *9 *9 *9 *9 *9 *9 *9
R Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
G Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
B Gain–*9 *9 *9 *9 *9 *9 *9 *9 *9
R Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
G Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
B Bias–*9 *9 *9 *9 *9 *9 *9 *9 *9
Luminance Gain–*9 *9 *9––––––
Chroma Delay–*9 *9 *9––––––
Fine Menu 2 Aspect–
   
Cinema–

–*2

–*2 *2
VCR Mode
 
––––––
Black Level
   
*10

FRC
    
CEC– ––––*3––*3 *3
Picture Shift V–*4 *4 *4 *4 *4 *4 *4 *4 *4
Overscan–

–

–*7
RGB/HD Adjust Mode– ––––

––

*11
Readjust– ––––*5––*5 *5  *11
Resolution H– ––––*6––*6 *6  *11
Resolution V– ––––*6––*6 *6  *11
Position H– ––––*5––*5 *5  *11
Position V– ––––*5––*5 *5  *11
Phase– ––––*5––*5–
Clamp Position– ––––*5––*5–
Clamp Width– ––––*5––*5–
714@6@@&/(
 
 
 
 
 .
 
 
						

							23
ENGLISH
NO SIGNAL VALID SIGNAL
ANY INPUTVIDEO or S-VIDEO COMPONENT
3(# )%.*
NTSC PAL/SECAM 480i/576i 480p/576p 480i/576i 480p/576p Other1080i/720p/
1080p/540p
HDMI CSC HDMI 1

–––– –– ––

CSC HDMI 2

–––– –– ––

Deep Color HDMI 1

–––– –– ––

Deep Color HDMI 2

–––– –– ––

Display Keystone
    
Scale–
   
Width–
   
Position H–
   
Position V–
   
Color Wheel
    
Installation
    
OSD/Blanking Menu Position
    
Language
    
Status Info.
    
Power-OFF Confirm.
    
Blanking Memory–
   
Blanking Top–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Bottom–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Left–*8 *8 *8 *8 *8 *8 *8 *8 *8
Blanking Right–*8 *8 *8 *8 *8 *8 *8 *8 *8
Configuration Auto Power Off
    
Trigger 2 Full
    
Trigger 2 Normal
    
Trigger 2 Zoom
    
Trigger 2 V-Strech
    
Trigger 2 Through
    
Remote Control
    
Reset Lamp Life
    
Reset All
    
*1 Can be selected only when User is selected for the Picture Mode.
*2 On only when interlaced signals are input. (Off for progressive signals.)
*3 On only when 1035i / 1080i signals are input.
*4 On when Aspect is set to V-Stretch for HD signals. For other signals, On when Aspect is set to Zoom or V-Stretch.
*5 On when the RGB/HD Adjust mode is set to Memory.
*6 On when the RGB/HD Adjust mode is set to Memory. However, as an exception, it is Off when Aspect is set to Through or V-Stretch.
*7 On when 480i/p or 576i/p signals are input.
*8 On when Blanking Memory is selected for OSD/Blanking.
*9 Cannot be selected when the default is selected for Picture Mode.
*10 Can be selected when the input signal is 540p, 720p, 1035i, 1080i, or 1080p.
*11 Off when the input signal is 480i/p or 576i/p.
714@6@@&/(
 
 
 
 
 .
 
 
						

							24
ENGLISH
This projector has menus that make setting and adjustment easy.1.
Press the MENUbutton. The MENU screen appears on the screen.
2.
Use the 3and 4buttons to select a menu (Picture Adjust, Fine Menu 1, Fine Menu 2, Input Signal,
RGB/HD Adjust, Display, OSD/Blanking, Config) and press the 2button.
For image mode selection, see “Picture Mode”.  (

P.24)
3.
Use the 3and 4buttons to select a menu item and press the 2button.
4.
Use the 3, 4, 1and 2buttons to make the setting or adjustment of the selected item.
•The current setting or adjustment level is displayed to the right of each menu item.
5.
Press the MENUbutton again to close the menu.
–Adjustment bar
When there is a “” right of a menu item, this 2acts as a button for engaging an adjustment mode. In
the adjustment mode, the menu disappears and only an adjustment bar, like that shown below,
appears along the bottom of the display. Use the 1and 2buttons to adjust the item to the desired
level. Press the 3button to return to the menu.Contrast 0
INPUT V-MUTE
ENTERMENU
ASPECT
CINEMA
VCR MODE
BLACK LEVEL
PATTERN
BLACKINFO.I M
A
BLANKING
B1
OFF
B3
B2
1, 5
2, 3, 4
1, 5 2, 3, 4User 1
Gamma
Contrast
Brightness
Color
Tint
0
0
03 0
Lamp Mode Color Temp.
Normal AIris
1
C
D
E BA
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD AdjustOSD/Blanking
Theater
Standard
Dynamic
Config.DisplayHDMI
Sharpness0
How to Operate Menus
Main menu Menu item  Setting or adjustment level This unit has four picture modes: Theater, Standard, Dynamic and User. The picture quality recommended
by Marantz is already set for each mode. The User mode has eight gamma curves that can be chosen and
saved by users. Also, the Theater, Standard and Dynamic modes three indexes for memorizing picture
quality adjustments. Similarly, the User mode has nine, making a total of 18 indexes available for use. 
–Theater: Reproduces the black suited for movie software.
–Standard: Suited for normal movie software.
–Dynamic: Suited for visually dynamic image software.
–User 1-9: Enable the user to adjust the gamma curve as preferred.(

P.25).
Picture mode selection
There are two ways to select the Picture mode: selecting a mode from the MENU screen or pressing
the picture mode buttons (THTR, STD, DYN) on the remote controller. To use the remote controller
buttons to select a picture mode, make sure the MENU screen does not appear on the screen and
press the desired picture mode button any number of times. (

P.6)
To select an picture mode from the menu, do as follows.
1.Press the MENUbutton. The MENU screen appears on the screen.
2.Use the 3/4buttons to select the Picture Mode displayed at the top of the menu.
3.Press the ENTERbutton to display the picture mode selection screen. Use the 3, 4, 2and 1
buttons to select an picture mode.
4.Press the ENTERbutton to decide the selected picture mode. Once the mode has been
entered, the screen returns to the previous menu.
Memorizing settings in an index
The settings made in “Picture Adjust” and “Fine Menu 1” of the main menu are automatically
memorized in the currently selected picture mode. Therefore, first select an picture mode and index,
and then make settings.
Note: 
When default is selected, “Picture Adjust” and “Fine Menu 1” cannot be selected from the menu.
Theater
Standard
Dynamic
UserDefault
1
Default
1
Standard 1Picture Adjust
Fine Menu 1
Fine Menu 2
Input SignalOSD/BlankingConfig.RGB/HD AdjustDisplay
2
3 1 Default
HDMI
Picture Mode
Picture mode  IndexTheater Default, 1, 2, 3Standard Default, 1, 2, 3Dynamic Default, 1, 2, 3
User 1, 2, 3, 4, 5, 6, 7, 8, 9
714@6@@&/(
 
 
 
 
 .
 
 
						

							25
ENGLISH
–Gamma setting
To change the type of Gamma curve, set the Picture Mode (

p.24) to User (1 – 9). Select “Gamma”
from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or
Dynamic).
–Color Temp. (Color Temperature)
1 : Red comes out strong. Color temperature is about 5250 K.
2 : Red is mildly strong. Color temperature is about 5800 K.
3 : Normal. Color temperature is about 6500 K.
4 : Blue is mildly strong. Color temperature is about 7500 K.
5 : Blue comes out strong. Color temperature is about 9300 K.
HB : High Bright : Display brightest image.
NOTES:
- To adjust picture quality, set the index to a mode other than the default. See “Picture Mode”. 
(

P.24)
- The Gamma cannot be set unless User (1 - 9) is set for the Picture Mode (

P.24).
- Tint cannot be adjusted for RGB input. For details, see “Functions by Signal.” (
P.22-23)
- The settings made in Picture Adjust are saved in the currently selected Picture Mode index.
ABCDE
TheaterDynamic
Picture quality in each of the picture modes can be adjusted to your liking and those adjustments can be
saved in memory. 
User 1Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.HDMI
Gamma
Contrast
Brightness
Color
Tint
0
0
03 0
Lamp Mode Color Temp.
Normal AIris
1Sharpness0
Picture Adjust
Adjustments
A, B, C, D, E, Theater,
Standard, Dynamic
-50Ô
0Ô
50
(Weak) (Default) (Strong)
-50
Ô
0Ô
50
(Dark) (Default) (Bright)
-50
Ô
0Ô
50
(Light) (Default) (Deep)
R10
Ô
0Ô
G10
(Purple) (Default) (Green)
050
12345HB
(Red) (Blue)
Normal, Economy
12 3
Contrast (High) (Low)
Brightness (Low) (High)
Sets the lens and illumination
aperture.
Item
Gamma
Contrast
Brightness
Color
Tint
Sharpness
Color Temp. 
(Color Temperature)
Lamp Mode
Iris
714@6@@&/(
 
 
 
 
 .
 
 
						

							26
ENGLISH
–Cinema
Auto : Automatically selects the cinema mode when a video signal is input. 
NTSC: 3-2 pull down, PAL: 2-2 pull down
Off : Pull-down processing is not performed.
–VCR Mode
On : A projector is forced into the intra-field only deinterlacing mode.
Off : A projector is used with external field memories and operates in the full set of deinterlacing
modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing
using 3:2 pulldown detection (2:2 pulldown for 625/50 sources).
–Black level
Select the black level by a video source.
–FRC (Frame Rate Conversion)
Auto 1 :Frame Rate Conversion function is basically off. However FRC turns on automatically
depending on vertical  frequency of input signal. Normally, use this mode.
Auto 2 : Use this mode when the image stops momentarily. 
60Hz : Frame Rate Conversion function is “On”. (59.94Hz fixed)
50Hz : Frame Rate Conversion function is “On”. (50.00Hz fixed)
48Hz : Frame Rate Conversion function is “On”. (47.95Hz fixed)
–CEC (Chroma Error Correction)
On : Reduces CUE (Chroma Up-sampling Error) of 1080i signals.
Off : Normally, use this mode.
–Picture Shift V
When Aspect on the Picture Adjust menu is set to “Zoom” or “V-Stretch”, this setting allows the user to
move the projected image vertically in order to see parts on the image not appearing on the screen. 
–Overscan
Selects whether to show or hide picture borders with NTSC, PAL, SECAM, 480i, 480p, 576i and 576p
signals.
Enable: Does not display borders of image signals. (Normally, use this mode.)
Disable: Displays the entire image signal.Notes :•There are some parameters can not adjust according to input signal.
•The settings made in Fine Menu 2 are saved in each currently selected input signal source.Standard 1
Cinema
VCR Mode
Black LevelAuto
On
0 IRE
FRC Auto 1
0
Picture Shift V
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
CEC Off
HDMI
Overscan
EnableAspect
Full
Fine Menu 2
By adjusting this Fine Menu, you can make fine picture adjustment.
–Noise Reduction
Adjust the noise reduction.
–R Gain
This menu allows the users to set the gain for red.
–G Gain
This menu allows the users to set the gain for green.
–B Gain
This menu allows the users to set the gain for blue.
–R Bias
This menu allows the users to set the bias for red.
–G Bias
This menu allows the users to set the bias for green.
–B Bias
This menu allows the users to set the bias for blue.
–Luminance Gain
This menu allows the users to set the luminance gain.
–Chroma Delay
This menu allows the users to set the chrominance delay.Note :•The settings made in Fine Menu 1 are saved in the currently selected Picture Mode index (Default
excluded).
Standard 1
Noise Reduction
R Gain
G Gain
B Gain
0
0 R Bias
G Bias
B Bias0
0
000
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.HDMI
0
0 Luminance Gain
Chroma Delay
Fine Menu 1
Adjustments
050
-50Ô
0Ô
50
-50
Ô
0Ô
50
-50
Ô
0Ô
50
-50
Ô
0Ô
50
-50
Ô
0Ô
50
-50
Ô
0Ô
50
-50
Ô
0Ô
50
-5
Ô
0Ô
5
Item
Noise Reduction
R Gain
G Gain
B Gain
R Bias
G Bias
B Bias
Luminance Gain
Chroma Delay
Item
Aspect
Cinema
VCR Mode
Black level
FRC
CEC
Picture Shift V
Overscan
Adjustments
Full, Normal, Zoom, 
V-Stretch, Through
Auto, Off
On, Off
0 IRE, 7.5 IRE /Expand,
Normal (For HDMI input)Auto 1, Auto 2, 60Hz,
50Hz, 48Hz
On, Off
-50
Ô
0Ô
50
Enable, Disable
714@6@@&/(
 
 
 
 
 .
 
 
						

							27
ENGLISH
Standard 1
Component 1
Component 2
S-Video
VideoAuto
Auto
Auto
Auto
RGB Auto
HDMI2 HDMI1 Auto
AutoPicture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.HDMI
Input Signal
NTSC(NTSC-3.58)
: Conventional analog broadcasting used
mainly in USA, Canada, Taiwan, Korea, and
Japan.
PAL(PAL-4.43)
: Conventional analog broadcasting used
mainly in United Kingdom and Germany.
SECAM
: Conventional analog broadcasting used
mainly in France and Russia.
480p
: Standard digital broadcasting
540p
: Special digital broadcasting 
(for example: RCA DTC100)
576p
: Standard digital broadcasting
720p, 1080p
: High Definition digital broadcasting
1035i
: Japanese Hi-Vision broadcasting
–Mode
Auto: Each item is adjusted automatically.
Memory1-3: If something wrong with Auto Adjust, select Memory, please adjust each item manually.
–Readjust
Select to readjust settings automatically for each item in this menu.
–Resolution H, V
Adjusts the horizontal and vertical resolution of the RGB/HD input signals.
–Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal.
–Phase
Adjust the phase of the DMD dots and the computer signal input from the RGB IN. Adjust the picture
to where it looks clearest.
–Clamp Position, Width
Adjusts the clamp position and width used in RGB/HD input.
Standard 1
Mode
Readjust
Resolution H
Resolution V
Position H
Position VMemory 1
0
0
0
0 Phase
Clamp Position
Clamp Width
000
Picture Adjust
Fine Menu 1
Fine Menu 2
Input Signal
RGB/HD Adjust
Display
OSD/Blanking
Config.
123
HDMI
RGB/HD Adjust
Item
Mode
Readjust
Resolution H
Resolution V
Position H
Position V
Phase
Clamp Position
Clamp Width
Adjustments
Auto, Memory 1, Memory 2, Memory 3Yes, No
0
Ô
25
(Default) (Large)
0
Ô
25
(Default) (Large)
-50
Ô
0Ô
50
(Left) (Default) (Right)
-10
Ô
0Ô
10
(Down) (Default) (Up)
-10
Ô
0Ô
10
(Backward) (Default) (Forward)
-50
Ô
0Ô
50
(Backward) (Default) (Forward)
-50
Ô
0Ô
50
(Small) (Default) (Large)
Item Adjustments
Component1, Auto, 480i/576i, 480p, 540p, 576p,
Component2 720p, 1035i, 1080i, 1080pS-Video Auto, NTSC, PAL, SECAMVideo Auto, NTSC, PAL, SECAM
RGB Auto, 480i/576i, 480p, 540p, 576p,
720p, 1035i, 1080i, 1080p
HDMI 1, HDMI 2 Auto, 480i/576i, 480p, 576p, 720p, 
1035i, 1080i, 1080p
714@6@@&/(
 
 
 
 
 .